• ETRI Journal
• /
• 제41권1호
• /
• pp.32-41
• /
• 2019

We propose a speckle reduction technique in electronic holographic display systems, where digital micro-mirror array devices are used as spatial light modulators. By adopting a programmable filtration in a general 4-f optic configuration, it is shown that the signal spectrum components in the frequency domain of a viewing-window-based holographic display system can be selectively filtered. Compared to the widely utilized single-sideband filtration techniques in electronic holographic display systems, our proposed programmable filtration can be utilized to effectively reduce the speckles in the reconstruction of point-cloud-based computer-generated holograms. Experimental results are presented to verify our proposed concept.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1469-1474
• /
• 2007

In recent years, research to machine large-surface micro-features has become important because of the light guide panel of a large-scale liquid crystal display and the bipolar plate of a high-capacity proton exchange membrane fuel cell. In this study, in order to realize the systematic design technology and performance improvements of an ultra-precision machine for machining the large-surface micro-features, a structural characteristic analysis was performed using its virtual prototype. The prototype consisted of gantry-type frame, hydrostatic feed mechanisms, linear motors, brushless DC servo motor, counterbalance mechanism, and so on. The loop stiffness was estimated from the relative displacement between the tool post and C-axis table, which was caused by a cutting force. Especially, the causes of structural stiffness deterioration were identified through the structural deformation analysis of sub-models.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1343-1346
• /
• 2006

Optical performances of micro-pyramid arrays were simulated by ray tracing technique for the application of backlight unit of LCD. The angular distribution of the luminance and the on-axis luminance gain depended on the apex angle, the refractive index, and the density of micro-pyramids. The on-axis luminance reached a maximum when the apex angle was $90^{\circ}$. It also increased as the density and the refractive index of micro-pyramids increased. The present result showed that highly-efficient optical sheet might become realized by adopting micropyramid array and corresponding development of manufacturing processes.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.535-536
• /
• 2006

Researches about micro technology travel lively in these days. Such many researches are concentrated in the field of materials and a process field. But properties of micro materials should be known to give results of research developed into still more. In these various material properties, reliability data such as mechanical, optical, thermal property, etc is the basic property. In this paper, it is measured that is material properties of main BLU(Back Light Unit) components in LCD(Liquid Crystal Display). The pattern shape of prism sheet, diffuser film and reflective plate are measured by variable 3D scanning equipments. It is researched which is the method to measure an optimal 3D pattern shape in each components.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.407-410
• /
• 2002

Triangulation method, conoscopic holography method and interferometry method are analyzed for effective measurement of micro burr geometry, which is formed in micro drilling. To select proper sensor, cylinder with 0.5mm diameter is measured and the result shows that conoscopic holography method is effective for measuring highly inclined surface. Burr with 1.0mm height and 30$\mu\textrm{m}$ height are measured by all methods. The conoscopic holography method is probed to be most proper method for measuring micro burr. A Program for 3D display of measured burr is developed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2000년도 제1회 학술대회 논문집
• /
• pp.29-30
• /
• 2000

CaS:Pb thin film used as phosphor layer in electroluminescent devices were deposited by an atomic layer deposition (ALD). The photoluminescence emission and excitation spectra were measured at 5 and 300K for the $CaS:Pb^{2+}$ phosphors with different Pb concentration from 0.001 at.% to 0.648 at.%. The emission spectra of these samples were characterized as UV emission and blue emission with the center of peak around 360 and 425nm, respectively. The UV emission was dominant at the low $Pb^{2+}$ concentration of 0.001 at%, whereas with increase of Pb concentration, the blue emission became a major component and to longer wavelength.

• 전기학회논문지P
• /
• 제55권2호
• /
• pp.89-93
• /
• 2006

Recently as a people recognize a safety more about a high and large buildings the importance of a fire-damper which supplies fresh air into the building in case of fire increases greatly. Therefore, in this paper a fire-damper using a micro-controller is designed and fabricated. In the design of fire-damper a pressure sensor is modeled as a capacitor and the p-spice is used as a circuit simulator PIC16F72 is used as a micro-controller to drive a pressure sensor and to display a pressure value from the pressure sensor and to drive a motor to open and close a damper. A photo-coupler is used to protect a motor from a overcurrent.

• 한국광학회지
• /
• 제16권2호
• /
• pp.113-120
• /
• 2005

LCD-BLU(liquid crystal device-back light unit)에 사용되는 도광판의 미세 산란패턴을 만드는 새로운 방법으로서, 실리콘 웨이퍼의 비등방 식각에 의해 자연적으로 형성되는 3차원 결정면 구조를 이용하는 방법을 제안하였다. 실리콘 3차원 결정면을 갖는 도광판과 프리즘 시트의 원판을 설계 및 제작하였고, casting 공정을 통해 PDMS 재질로 복제된 도광판을 제작하여 특성을 분석하였다. 측정 결과, 기존 인쇄형 도광판에 비해 실리콘피라미드 패턴의 도광판이 $10\%$ 증가된 정면 휘도 효율을 가질 수 있음을 실험적으로 검증하였다.

• 방송공학회논문지
• /
• 제20권6호
• /
• pp.928-937
• /
• 2015

기존의 헤드업 디스플레이는 작은 허상 크기로 인하여 운전자가 영상 정보를 쉽게 인식할 수 없는 어려움을 가지고 있기 때문에, 본 연구에서는 수평 방향으로 영상을 넓히는 다중 화면 구조와 컴바이너 렌즈를 사용하여 영상 확대와 다채널 윈도우 구조의 헤드업 디스플레이를 연구하였다. 0.47inch 크기의 LCD를 사용하여 투과와 반사 기능의 허상 영상을 사람의 눈에서 3m 위치에 구현하는 기술을 연구하여 근거리와 원거리의 물체에 대한 운전자의 인지 시간을 짧게 하였다. 허상 영상의 콘텐츠로는 스마트 폰을 이용하여 다양한 내비게이션 정보 등을 디스플레이 할 수 있도록 하여 안전과 정보를 동시에 제공할 수 있도록 하였다.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.1-6
• /
• 2018

Micro prism pattern is applying in order to get increase of luminance, control the light, and so forth especially in optics and display industry. Most patterns are fabricated by lithography, planning, and EDM, but they have limitations on the productivity or the unit cost of produce. However, ultra precision mold is one of the processes able to replace it, and assure high productivity required by industries. In this investigation, micro prismatic end-milling is suggested in order to fabricate the pattern effectively. Micro prism pattern having $100{\mu}m$ of pitch and height was machined on STD-11. After machining, the flank and boundary wear on micro end mill were measured and analyzed, as well as burr formation and dimensional accuracy of fabricated pattern were evaluated. Thus the optimal cutting conditions were derived.