• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1540-1545
• /
• 2004

Measurement of concentration fields in a micro-channel is the crucial technology in the area of Lab-on-a-chip to be used for various bio-chemical applications. It is wel-known that the only possible way to measure the concentration field in the micro-channel is using micro-LIF(Laser Induced Fluorescence) method. However, an accurate concentration field at a given cross plane in a micro-channel has not been made so far due to the limit of light illumination. The present study demonstrates a novel method to provide an ultra thin laser sheet beam having 5 microns thickness by a micro focus laser line generator. Nile Blue A was used as fluorescent dye for LIF measurement. The laser sheet beam illuminates an exact plane of concentration measurement in the micro-channel to increase the signal to noise ratio and reduce the depth uncertainty considerably.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.301-304
• /
• 2006

This paper presents a review of the important recent literature available in the area of micro-channel flow analysis and mixing. The topics covered include the physics of flows in micro-channels and integrated simulation of micro-channel flows. Also the flow control models and electro-kinetically driven micro-channel flows are explained. A comparison of various mixing principles in micro-channels are provided in sufficient detail.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.313-317
• /
• 2003

Micro-Channel ultra-precision polishing is a new technology used in magnetic field-assisted relishing. In this paper, an electromagnet or the i18 of test system was designed and manufactured. A size of magnetic abrasive is used on 25~75${\mu}{\textrm}{m}$ and for the polish a micro-channel upper part. A surface of channel which is not even is manufactured using magnetic abrasive finishing at upper surface of micro-channel. As a result, the surface roughness rose by 80％ after upper surface of micro- channel was polished up 8 minutes by polishing.

• 소성∙가공
• /
• 제15권9호
• /
• pp.692-696
• /
• 2006

Micro fabrication of polymeric materials becomes increasingly important. And it is considered as a low-cost alternative to the silicon or glass-based Micro Electro-Mechanical System(MEMS) technologies. In the present study, micro channels were fabricated via LiGA(Lithographie, Galvanoformung, Abformung) process used for Capillary Electrophoresis(CE) chip. Taguchi method was applied to investigate the effects of process conditions in injection molding(melt temperature, injection speed, mold temperature and packing pressure) on the transcription characteristics of the micro channel. It was found that the skin layer disturbs a formation of micro channel. Furthermore, mold temperature and injection speed were two important factors to affect the replication characteristics of micro channel.

• Design & Manufacturing
• /
• 제16권3호
• /
• pp.58-65
• /
• 2022

Micro-fluidic chip has been fabricated by lithography process on silicon or glass wafer, casting using PDMS, injection molding of thermoplastics or 3D printing, etc. Among these processes, 3D printing can fabricate micro-fluidic chip directly from the design without master or template for fluidic channel fabricated previously. Due to this direct printing, 3D printing provides very fast and economical method for prototyping micro-fluidic chip comparing to conventional fabrication process such as lithography, PDMS casting or injection molding. Although 3D printing is now used more extensively due to this fast and cheap process done automatically by single printing machine, there are some issues on accuracy or surface characteristics, etc. The accuracy of the shape and size of the micro-channel is limited by the resolution of the printing and printing direction or layering direction in case of SLM type of 3D printing using UV curable resin. In this study, the printing direction and thickness of each printing layer are investigated to see the effect on the size, shape and surface of the micro-channel. A set of micro-channels with different size was designed and arrayed orthogonal. Micro-fluidic chips are 3D printed in different directions to the micro-channel, orthogonal, parallel, or skewed. The shape of the cross-section of the micro-channel and the surface of the micro-channel are photographed using optical microscopy. From a series of experiments, an optimal printing direction and process conditions are investigated for 3D printing of micro-fluidic chip.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1873-1876
• /
• 2003

Magneto-rheological polishing is a new technology used in precision polishing. It utilizes magneto-rheological fluid. nonmagnetic polishing abrasive, aqueous carrier fluids in magnetic field to remove material from a part surface. Silicon micro channel as work piece is fixed in the slurry which is made of MR fluid and CeO$_2$(10 vol%) abrasive particles. And permanent magnet rotate in the slurry to transfers magnetic force to abrasive particles by increasing yield strength of MR fluid. so, the obtained bottom surface roughness of micro channel by experiment reduced to Ra 0.010 $\mu\textrm{m}$ Rmax 0.103 $\mu\textrm{m}$ and finwall surface roughness of micro channel reduced to Ra 0.018 $\mu\textrm{m}$ Rmax 0.468 $\mu\textrm{m}$. At optimum conditions of variables, the workpiece as silicon micro channel have about 24 times smaller surface roughness than before polishing.

• International Journal of Vascular Biomedical Engineering
• /
• 제1권2호
• /
• pp.30-35
• /
• 2003

Flow characteristics of blood flow in a micro channel were investigated experimentally using a micro-PIV (Particle Image Velocimetry) velocity field measurement technique. The main objective of this study was to understand the real blood flow in micron-sized blood vessels. The Reynolds number based on the hydraulic diameter of micro-channel for deionized (DI) water was about Re=0.34. For each experimental condition, 100 instantaneous velocity fields were captured and ensemble-averaged to get the spatial distributions of mean velocity. In addition, the motion of RBC (Red Blood Cell) was visualized with a high-speed CCD camera. The captured flow images of nano-scale fluorescent tracer particles in DI water were clear and gave good velocity tracking-ability. However, there were substantial velocity variations in the central region of real blood flow in a micro-channel due to the presence of red blood cells.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2002년도 마이크로/바이오 가시화기술부문 학술강연회
• /
• pp.79-84
• /
• 2002

Most microfluidic devices such as heat sinks for cooling micro-chips, DNA chip, Lab-On-Chip, and micro pumps etc. have microchannels of various size. Therefore, the design of practical microfluidics demands detail information on flow structure inside the microchannels. However, detail velocity field measurements are rare and difficult to carry out. In addition, as the microfluidics expands, accurate understanding of microscale transport phenomena becomes very important. In this research, micro-PIV system was employed to measure the velocity fields of flow inside a micro-channel. We carried out PIV measurements for several microchannels with varying channels width, inlet and outlet shape, filters, CCD camera and ICCD camera, etc. For effective composition of micro-PIV system, first of all, it is essential to understand optics related with micro-imaging of particles and the particle dynamics encountered in micro-scale channel flows. In addition, it is necessary to find the optimal condition for given experimental environment and? micro-scale flow to be investigated. The problems encountered in measuring velocity field of micro-channel flows are discussed in this paper.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권5호
• /
• pp.482-487
• /
• 2005

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.1894-1899
• /
• 2007

This paper presents the thermal characteristics for micro heat exchanger with different micro-channel shapes. The shapes of micro-channel has been manufactured sheet metal by chemical etching for the I shape of straight channel and V and W shapes of chevron feature and fabricated micro plated heat exchangers using the vacuum brazing of bonding technology. The experimental study has been performed on heat transfer and pressure drop characteristics with various Reynolds number for water to water at the counter flows. The average heat transfer rate of V and W shapes has been showed about 1.5${\sim}$1.6 times large than those of I shape. For the comparison of Nusselt number, it is known that the convective heat transfer of V and W shapes represent more effect than I shape. The pressure drops of V and W shapes are about 1.2${\sim}$1.7 times lager than those of I shape.