• Journal of Korea Water Resources Association
• /
• v.56 no.12
• /
• pp.919-928
• /
• 2023

Rainfall characteristics in Korea are concentrated during the summer flood season. In particular, when a large amount of turbid water flows into the dam due to the increasing trend of concentrated rainfall due to abnormal rainfall and abnormal weather conditions, prolonged turbid water phenomenon occurs due to the overturning phenomenon. Much research is being conducted on turbid water prediction to solve these problems. To predict turbid water, turbid water data from the upstream inflow is required, but spatial and temporal data resolution is currently insufficient. To improve temporal resolution, the development of the Turbidity-SS conversion equation is necessary, and to improve spatial resolution, multi-item water quality measurement instrument (YSI), Laser In-Situ Scattering and Transmissometry (LISST), and hyperspectral sensors are needed. Sensor-based measurement can improve the spatial resolution of turbid water by measuring line and surface unit data. In addition, in the case of LISST-200X, it is possible to collect data on particle size, etc., so it can be used in the Turbidity-SS conversion equation for fraction (Clay: Silt: Sand). In addition, among recent remote sensing methods, the spatial distribution of turbid water can be presented when using UAVs with higher spatial and temporal resolutions than other payloads and hyperspectral sensors with high spectral and radiometric resolutions. Therefore, in this study, the Turbidity-SS conversion equation was calculated according to the fraction through laboratory analysis using LISST-200X and YSI-EXO, and sensor-based field measurements including UAV (Matrice 600) and hyperspectral sensor (microHSI 410 SHARK) were used. Through this, the spatial distribution of turbidity and suspended sediment concentration, and the turbidity calculated using the Turbidity-SS conversion equation based on the measured suspended sediment concentration, was presented. Through this, we attempted to review the applicability of the Turbidity-SS conversion equation and understand the current status of turbid water occurrence.

• Journal of Digital Convergence
• /
• v.11 no.8
• /
• pp.65-73
• /
• 2013

Outcome of election depends on which candidate of politics uses more original and creative idea for Ads and PR of election in election campaign strategy of political campaign. Especially, since political Ads and PR are the ways of capturing voters' sensitivities with one line of copy(slogan) and one image, Ads and PR are very important. This research analyzes unique and creative trend of political campaigns which are used in each unit election which is held four times(2010. 6 2 local election, 2011. 10 26 by-election, 2012. 4 11 general election, 2012. 12 19 presidential election) during 2010~2012. For analysis, search analysis of text and image used in video, internet, booklet type of Ads and PR material for election, and election campaign. Video is used in election campaign during election period. Unique and creative political campaign is customized micro-marketing election strategy trend which tries to fit for tendency of backing including gender, age group, social atmosphere, etc. This research excludes the degree of success of this election strategy from subject of analysis.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.138-142
• /
• 2004

In this paper, we present a new method for monitoring of ECU's sensor signals of vehicle. In order to measure the ECU's sensor signals, the interfaced circuit is designed to communicate ECU and the Embedded Linux is used to monitor communication result through Web the Embedded Linux system and this system is said "ECU Interface Part". In ECU Interface Part the interface circuit is designed to match voltage level between ECU and SA-1110 micro controller and interface circuit to communicate ECU according to the ISO, SAE communication protocol standard. Because Embedded Linux does not allow to access hardware directly in application level, anyone who wants to modify any low level hardware must develop device driver. To monitor ECU's sensor signals the most important thing is to match serial level between ECU and ECU Interface Part. It means to communicate correctly between two hardware we need to match voltage and signal level, and need to match baudrate. The voltage of SA-1110 is 0 ${\sim}$ +3.3V and ECU is 0 ${\sim}$ +12V and, ECU's communication Line K does multiple operation so, the interface circuit is used to match voltage and signal level. In Addition to ECU's baudrate is 10400bps, it's not standard baudrate in computer environment. So, we need to develop a device driver to control the interface circuit, and change baudrate. To monitor ECU's sensor signals through web there's a network socket program is working in Embedded Linux. It works as server program and manages user's connections and commands. Anyone who wants to monitor ECU's sensor signals he just only connect to Embedded Linux system with web browser then, Embedded Linux webserver will return the ActiveX webbased measurement software. It works in web browser and inits ECU, as a result it returns sensor signals through web. All the programs are developed with GCC(GNU C Compiler) and, webbased measurement software is developed with Borland C++ Builder.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.12
• /
• pp.1221-1227
• /
• 2015

Diffusion bonding is the key manufacturing process for the micro-channel type heat exchangers. In this study, austenitic alloys such as Alloy 800HT, Alloy 690, and Alloy 600, were diffusion bonded at various temperatures and the tensile properties were measured up to $650^{\circ}C$. Tensile ductility of diffusion bonded Alloy 800HT was significantly lower than that of base metal at all test temperatures. While, for Alloy 690 and Alloy 600, tensile ductility of diffusion bonded specimens was comparable to that of base metals up to $500^{\circ}C$, above which the ductility became lower. The poor ductility of diffusion bonded specimen could have caused by the incomplete grain boundary migration and precipitates along the bond-line. Application of post-bond heat treatment (PBHT) improved the ductility close to that of base metals up to $550^{\circ}C$. Changes in tensile properties were discussed in view of the microstructure in the diffusion-bonded area.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.57-57
• /
• 2017

Water line은 UV 처리된 호스의 내부에 압력보상 기능이 첨부된 경질의 미로 튜브를 끼워 사용하도록 제작되어 있다. 점적 호스의 외경은 15.8mm이며 대부분 0.5~2.5bar 사이의 압력에 1.5~3.0 L/hr의 유량을 공급한다. 따라서 전적 호스의 내부에 위치한 경질 미로 튜브의 설계는 유량의 압력보상에 밀접한 관계가 있다. 본 연구에서는 경질 미로 튜브를 통과하는 작은 돌기의 수가 압력과 유량에 어떤 영향을 미치는지에 대한 기초적인 실험을 수행하였으며 경질 미로의 압력과 유량 특성에 따른 이론적 해석과의 비교분석을 통하여 새로운 미로의 형상 설계에 활용할 기초적 연구를 수행하고자 하였다. 점적 호스의 성능은 길이(보통 300~400m)에 대한 유량의 균등성을 유지하는 것이며 균등성은 압력보상에 의해 이루어진다. 원통형 미로는 점적 호스의 내부에 삽입되어 원통 부분에 형성된 미로의 길이에 따른 유량의 균등성을 유지하도록 설계되어 있다. 점적 호스의 원통 주변에는 8개의 미로로 구성되어 있으며 미로의 길이를 금속 평면으로 금형 제작하여 투명판에서 미로의 형상을 보이게 하였다. 또한 입구부분에 물을 공급하고 미로의 각 위치별 배출구를 설치하여 압력에 따른 유출량을 전자저울에 측정하여 압력별 유량의 균등성에 대한 데이터를 측정하였다. 유입구의 압력을 0.5, 1.5, 2.5, 3.0bar로 각각 공급하였으며 유출량은 미로의 8개 구간에 따라 측정하였다. 경질 미로의 유출량은 미로의 길이가 짧을수록, 압력이 커질수록 유출량이 높게 나타났다. 또한 미로의 길이가 짧을 경우에는 유출량의 차이가 비교적 크게 나타났으나 미로의 길이가 길수록 압력에 대한 유출량에 대한 차이가 크지 않음을 알 수 있었다. 따라서 경질 미로에서 미로의 길이를 길게 할 경우에는 유출량을 비교적 균일하게 할 수 있음을 보여주고 있다. 반면에 미로의 길이가 길어질수록 압력변화에 따른 유출량이 지수적으로 감소함을 나타내고 있다. 미로의 길이가 7번과 8번에서는 상당히 균일한 성능을 보여주므로 경질 미로의 배출구를 전체적으로 모두 활용함으로써 압력보상을 비교적 균일하게 할 수 있음을 보여주고 있다. 압력보상은 탄성을 가진 실리콘과 미로로 구성될 경우에 가장 큰 효과를 나타내지만 점적 호스와 같이 경질 미로만으로 압력보상을 해야 할 경우에는 경질 미로의 길이가 매우 중요하다.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.56-56
• /
• 2017

점적 호스 중 PC 드립은 경질 호스의 내부에 Micro-path가 부착된 유로장치와 압력을 보상하는 연질의 실리콘으로 구성되어 있다. 이때 일정압력에서 적정 길이까지 동시에 내부 압력을 유지하며 균등하게 유출구를 통하여 유량을 공급하는 압력보상 기능이 매우 중요하다. 그러나 이 부분에 대한 기술은 선진국에 비해 아직 부족하여 수입에 의존하는 경향이 매우 높다. 뿐만 아니라 선진국 제품에 비해 유로장치 및 연질 실리콘의 탄성이 균일하지 못해 압력에 따른 유량의 편차가 큰 편이다. 본 연구에서는 우리나라 제품의 PC 드립 압력 균등성 기술을 향상시키기 위해 PC 드립의 핵심기술인 연질 실리콘의 성능에 대한 평가와 유량의 편차를 분석하여 문제점을 통한 개선방안을 제시하고자 하였다. 연질 실리콘의 규격은 $17{\times}8{\times}0.85mm$ (가로${\times}$세로${\times}$두께)로서 Water line의 내부에 결합되어 구성된다. PC 드립용 실리콘은 국내 A사 제품을 중심으로 하여 성능을 측정하였다. 측정을 정밀하게 하기 위해 Microtester를 사용하여 일정하게 하중이 부과되도록 하였다. 연질의 실리콘의 경도는 압력 보상에 중요한 기능을 하고 있으며 또한 PC 드립의 경질 미로와 같이 압력을 제어하는 역할을 하고 있다. 국내 A사의 실리콘 경도는 이상적인 실리콘 경도에 비하면 매우 불균일하였다. 세부적으로는 40 이하의 낮은 경도에서는 비교적 일치하였으나 경도 45 이상에서는 큰 차이를 보여주고 있었다. 국내 A사의 실리콘 경도에 따른 공급유량의 특성에서는 실리콘의 경도가 낮을수록 실리콘은 무르며 탄성이 줄어든다. 반면에 경도가 높을수록 탄성이 커지고 딱딱한 특성을 가진다. 동일한 PC 드립에 실리콘의 경도별 특성은 경도에 따른 유량이 반드시 일정하지 않으며 대체로 경도가 높을수록 동일 압력에 대해 유량이 많아지는 것을 알 수 있었다. 압력의 변화에 대해 유량이 일정하게 유지하는 특성을 가질수록 사용범위가 넓어지고 안정성이 높은 것으로 판단되며 실리콘 경도 35~55 범위에서 1~2bar의 공급압력에서 사용하는 것이 적합할 것으로 보여진다. 경도 45의 실리콘을 사용하여 수입 드립, 국내 A사의 드립 및 수입과 국내 혼용시 압력에 따른 공급유량의 특성을 분석하였다. 최대 유량과 최소 유량에서 발생되는 오차는 수입 실리콘이 비교적 작았으나 3.6 bar 이상에서는 유량이 급격히 떨어지는 양상을 보였다. 국내 A사의 제품은 0.8~2.0 bar 까지 성능이 비슷했으나 0.8 bar 이하에서는 오차가 있었으나 높은 압력에서는 오히려 성능이 우수하였다. 수입 드립과 다소 유사한 성능을 나타낸 것이 A사 드립과 수입 실리콘을 혼용하여 사용한 것은 전체적으로 비슷한 양상을 나타내었다. 따라서 실리콘 경도 오차를 고려하면 압력별 유량의 변화는 실리콘의 경도와 밀접한 관계가 있는 것으로 판단되었다.

• KSBB Journal
• /
• v.13 no.3
• /
• pp.231-237
• /
• 1998

An attenuated Japanese encephalitis virus (JEV) clone SA-14-14-2(Vero) was obtained through successive adaptation of a primary cell adapted strain, SA-14-14-2(PDK) to Vero cell, a continuous line of monkey kidney cells. The virus titer reached above the 107 plaque forming unit (pfu) per mL of culture supernatant with 3 passages in Vero cells and was maintained close to this level in the further passages. The optimum temperature for the virus growth was $35^{\circ}C$. Growth pattern of the virus indicated that optimum time for the virus harvest is 4 days post infection and the virus accomplished rapid initial propagation even in medium containing no serum supplement. The roller bottle (RB) system and the spinner flask (SF) system using micro-carrier (Cytodex-1) for the JEV cultivation were explored. When RB, SF, and T-flask culture system were compared, there was no significant difference in virus yield. Furthermore, the results indicated that virus could be harvested multiple times from 3 days to 9 days post infection; neither severe cytopathic effect (CPE) in the infected cells nor the decrease in the titer was observed on duration of 9 days.

• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.601-606
• /
• 2000

Nickel mono-silicide(NiSi) shows no increase of resistivity as the line width decreases below 0.15$\mu\textrm{m}$. Furthermore, thin silicide can be made easily and restrain the redistribution of dopants, because NiSi in created through the reaction of one nickel atom and one silicon atom. Therefore, we investigated the deposition condition of Ni films, heat treatment condition and basic properties of NiSi films which are expected to be employed for sub-0.15$\mu\textrm{m}$ class devices. The nickel silicide film was deposited on the Si wafer by using a dc-magnetron sputter, then annealed at the temperature range of $150~1000^{\circ}C$. Surface roughness of each specimen was measured by using a SPM (scanning probe microscope). Microstructure and qualitative composition analysis were executed by a TEM-EDS(transmission electron microscope-energy dispersive x-ray spectroscope). Electrical properties of the materials at each annealing temperature were measured by a four-point probe. As the results of our study, we may conclude that; 1. SPM can be employed as a non-destructive process to monitor NiSi/NiSi$_2$ transformation. 2. For annealing temperature over $800^{\circ}C$, oxygen pressure $Po_2$ should be kept below $1.5{\times}10^{-11}torr$ to avoid oxidation of residual Ni. 3. NiSi to $NiSi_2$ transformation temperature in our study was $700^{\circ}C$ from the four-point probe measurement.

• Journal of Aquaculture
• /
• v.19 no.4
• /
• pp.225-230
• /
• 2006

A long-term (26 weeks) feeding experiment was conducted to examine the essentiality and requirement of inositol in diets for olive flounder because no information is available in the species. Five casein-gelatin based semi-purified diets were formulated to contain four different levels of myo-inositol (0, 0+antibiotic, 400, 800, and 1600 mg/kg, designated as M0, M0+, M400, M800, and M1600, respectively). One (M0+) of the control diets contained tetracycline hydrochloride (0.4%, wt/wt) as an antibiotic to inhibit biosynthesis of inositol by micro-organism in intestine of fish. Olive flounder at the early juvenile stage (initial body weight 1.22 g) were randomly distributed into fifteen 35 L tanks (48 fish/tank) and fed with one of the experimental diets (3 replicates per diet). At the end of the feeding trial, the weight gain, feed intake, specific growth rate, and protein efficiency ratio of fish fed diets containing higher levels of myo-inositol (M800 & M1600) were significantly higher than those of fish fed the other diets (P<0.05). Feed conversion ratio, survival, hematocrits, and hemoglobin of fish fed experimental diets were not significantly different among all the fish groups. Whole body compositions of fish were not different except for lipid content. The lipid content was significantly different between M0 and M400 diet groups. These results indicate that juvenile olive flounder requires dietary supplementation of myo-inositol in diets for normal growth and its optimum level seems to be approximately 800 mg myo-inositol/kg diet.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.34 no.5
• /
• pp.571-577
• /
• 2008

Introduction: Possible etiologic factors associated with bone loss around implants after implantation are surgical trauma, occlusal overload, periimplantitis, presence of micro gap and the formation of biologic distances. Tarnow et al. observed that the crestal bone loss was greater when the distance between the implants was <3mm than when the implants were ${\geq}\;3mm$ apart. The aim of this study was to evaluate the influence of different interimplant distance on marginal bone and crestal bone resorption in the beagle dogs. Materials and methods: The mandibular premolars of 5 dogs were extracted bilaterally. After 12 weeks of healing, each dog received 7 implants. On each side, implants were separated by 2mm (Group 1) and by 5mm (Group 2). After 16 weeks of healing, the dogs were sacrificed. Marginal bone loss was determined through linear measurements made between the implant-abutment junctions and the most coronal portions of the bone in contact with the implant surface. A line was drawn uniting the implant-abutment junctions of the adjacent implants, and a linear measurement was made at the midpoint in the direction of the most coronal peak of the interimplant bone crest to determine the crestal bone loss. Both of them was measured radiologically and histologically. Result and conclusion: In radiological analysis, the mean of marginal bone loss was $1.26{\pm}0.14mm$ for group 1 and $1.23{\pm}0.34mm$ for group 2, the mean of crestal bone loss was $1.10{\pm}0.14mm$ for group 1 and $1.02{\pm}0.30mm$ for group 2. The results were not statistically significant between 2 groups. In histological analysis, the mean of marginal bone loss was $1.63{\pm}0.48mm$ for group 1 and $1.62{\pm}0.50mm$ for group 2, the mean of crestal bone loss was $1.23{\pm}0.35mm$ for group 1 and $1.15{\pm}0.39mm$ for group 2. The differences were also not statistically significant. The clinical significance of this result is that the increase in the crestal bone loss results in the increase in the distance between the base of the interproximal contact of the crowns and the bone crest, and this determines if papilla will be present or absent between implants. Considering this fact, keeping up sufficient interimplant distance is important to minimize crestal bone loss.