• Journal of the Korean Institute of Gas
• /
• v.24 no.5
• /
• pp.39-46
• /
• 2020

This paper is considered about centerline segregation of API 5L steel used in pipeline. Mn/S, Nb and C were known as segregated elements in the centerline of pipe thickness. The Mn usually was accompanied by S consisting of long viscous shape. Microstructure of the centerline was composed of MnS and Nb/Ti indusions including oxide. The segregation effect in centerline region was analyzed by OM, SEM/EDS and micro Vickers hardness. The Mn, Nb and C are retarded elements in transformation from austenite to ferrite or martensite. These elements could derive a bainitic microstructure as a kind of martensite, which is different from difference and element segregation between in matrix and centerline derived from steel melting and heat treatment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.75-81
• /
• 2011

Dissimilar joining of aluminum 6061-T6 alloy to aluminum 5083-O alloy was performed using friction-stir welding technique. The mechanical properties, hardness, macro- and micro-structure on dissimilar friction-stir-weld aluminium alloy were investigated. Mechanical properties of the weld mainly depend on which Al alloy is placed at the retreating sides of the rotating tool respectively during dissimilar friction-stir weld because the microstructure of stir zone was mainly composed of welded Al alloys of the retreating side. Onion ring pattern was observed like lamella structure stacked by each Al alloy in turn. It apparently results in defect-free weld zone that traverse speed was changed to 124 mm/min under conditions of tool rotation speed like 1250 rpm with 5 mm of tool's prove diameter, 4.5 mm of prove length, 20 mm of shoulder diameter, and $2^{\circ}$ of tilting angle. The 231 MPa of ultimate stress and the 121 MPa of yield point are obtained about the friction-stir-welded Al 6061-T6(AS) to Al 5083-O(RS).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.703-703
• /
• 2013

다이아몬드상 탄소 박막(Diamond-like carbon, DLC) 박막은 낮은 마찰 계수, 높은 내마모성, 화학적 안정성, 적외선 영역에서의 높은 투과율 등의 장점을 바탕으로 MEMS (Micro-Electro Mechanical System) 소자와 MMAs (Moving Mechanical Assemblies)의 고체윤활코팅, 마그네틱 미디어와 하드디스크의 슬라이딩 표면 등 다양한 분야에 코팅소재로써 응용되어왔다 [1,2]. 현재 전기철도용 집전판은 마찰이 적고 전도성을 지니는 카본 소재로 구성되어 있다. 그러나 그 마모 비율이 너무 심하여 이를 개선할 수 있는 방안으로 고경도 저마찰력을 지니는 DLC 박막을 코팅 소재로써 제안하고자 한다. 그러나 기존에 DLC 박막은 절연특성이 매우 우수하기 때문에 기존에 전도성을 지니는 카본 집전판에 적용하기에는 어려움이 따른다. 따라서 DLC 박막 내에 실리콘(Si) 또는 금속(Metal)을 첨가시키거나, 금속 중간층을 포함시켜 전기적으로 전도특성을 향상시키는 방안이 제시되고 있으며, 본 연구에서는 DLC 박막과 유사하게 우수한 경도특성을 지니고, 낮은 마찰계수등을 지니는 비정질 탄소박막을 연구하여 카본 집전판에 코팅하고자하며, 특히 비정질 탄소박막에 금속 Ti를 도핑하여 집전판과의 접착력과 전기적 전도 특성을 향상시키고자 한다. Ti가 도핑된 탄소박막(TiC) 박막은 비대칭 마그네트론 스퍼터링(unbalanced magnetron sputtering; UBMS) 시스템을 이용하여 제작하였으며, 스퍼터링 조건 중 기판에 인가되어지는 기판온도에 따라 변화되어지는 TiC 박막의 트라이볼로지(Tribology) 특성을 고찰하고자 하였다. 증착시 기판온도의 증가는 TiC 박막의 경도, 마찰계수 특성등 트라이볼로지 특성을 향상시켰으며, 전기적 전도 특성을 향상시켰다. 이러한 결과는 스퍼터링 방법에 의해 증착되어진 TiC 박막내에 존재하는 sp2 결합과 관계가 있음을 확인할 수 있으며, 트라이 볼로지 특성은 TiC 박막내에 sp2 탄소결합의 비율 증가와 관련되어졌다. 특히 sp2 탄소결합은 TiC 박막 증착시 증가된 기판온도와 밀접한 관계가 있으며 기판온도의 증가에 따라 나노결정 클러스터의 크기와 수의 변화와 밀접한 관계가 있음을 확인하였다. 결국 기판온도는 TiC 박막의 트라이볼로지 특성을 향상시켰으며, 전기적 특성 또한 향상시켜 전기철도 집전판에 응용을 위한 소재로 평가할 수 있다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.254-254
• /
• 2013

마그네트론 스퍼터링은 그 단순한 구조로 인하여 신뢰성과 확장성이 높은 기술이다, 이로 인해 DLC, ITO 등의 산업 분야에서 많이 사용하는 박막 공정 기술이다. 하지만 인듐과 같은 희토류 금속의 가격이 최근 상승함에 따라 나타난 낮은 타겟 효율성의 문제와 낮은 파워 밀도로 인한 기판의 추가적인 bias 추가에 따른 비용상승, 그리고 reactive 스퍼터링 시 낮은 증착률 등의 문제점들 또한 존재한다. 이러한 단점들을 해결하기 위해 많은 연구들이 이루어 졌으며, 높은 파워 밀도를 위해 High power Impulse Plasma Magnetron Sputtering (HIPIMS) 기술과 타겟 사용률을 높이기 위한 High Target Utilization Sputtering (HITUS) 등의 기술 등이 개발되었다. 본 연구에서는 직류 전원을 사용한 High density Plasma Sputtering System (HIPASS)이라 명하는 고밀도 원거리 플라즈마 소스를 이용한 스퍼터링 이용해 증착한 박막의 특성을 연구 하였다. Hollow cathode discharge에서 발생한 고밀도 플라즈마가 외부 유도 자장 코일에 의하여 타겟 표면까지 도달하게 되며, 스퍼터링 타겟의 고전압 bias에 의해 플라즈마 이온들이 가속이 이루어져 스퍼터링 공정이 이루어 지게 된다. 본 연구의 공정에서 타겟 사용 효율은 최대 90%까지 이며, 원거리 플라즈마 소스에서의 이온으로 스퍼터링을 실시함으로 인해 스퍼터링 전압과 전류의 독립적인 조절이 가능 하다. 본 연구에서 HIPASS을 이용하여 기판에 추가적인 전압 인가 없이 Ti 타겟과 아르곤/질소 혼합가스를 사용하여 TiN 박막을 증착 하였다. TiN의 증착률은 약 44 nm/min였으며, 이 박막의 XRD 분석 결과 TiN (111), (200), (220) 면들이 관찰이 되었다. 높은 스퍼터링 입자 에너지에서 증착 된 TiN 박막에서 우선적으로 나타나는(200)과 (220) 면들이, 본 실험에서는 기판에 추가적인 전압인가 없이도 우선방위 성장을 보였다. 이 박막의 micro-hardness 측정 결과 약 34.7 GPa이며, 이는 UBM 이나 HIPIMS에서 보여주는 결과에 준하거나 그 이상의 수치이다. 이와 같은 결과는 본 연구에서 사용한 HIPASS 증착 공정이 높은 스퍼터링 입자 에너지를 가지기에 고밀도의 TiN 박막이 증착 된 결과로 볼 수 있다.

• Journal of Powder Materials
• /
• v.18 no.1
• /
• pp.64-72
• /
• 2011

Nondestructive instrumented indentation test is the method to evaluate the mechanical properties by analyzing load - displacement curve when forming indentation on the surface of the specimen within hundreds of micro-indentation depth. Resistance spot welded samples are known to difficult to measure the local mechanical properties due to the combination of microstructural changes with heat input. Particularly, more difficulties arise to evaluate local mechanical properties of resistance spot welds because of having narrow HAZ, as well as dramatic changed in microstructure and hardness properties across the welds. In this study, evaluation of the local mechanical properties of resistance spot welds was carried out using the characterization of Instrumented Indentation testing. Resistance spot welding were performed for 590MPa DP (Dual Phase) steels and 780MPa TRIP (Transformation Induced Plasticity) steels following ISO 18278-2 condition. Mechanical properties of base metal using tensile test and Instrumented Indentation test showed similar results. Also it is possible to measure local mechanical properties of the center of fusion zone, edge of fusion zone, HAZ and base metal regions by using instrumented indentation test. Therefore, measurement of local mechanical properties using instrumented indentation test is efficient, reliable and relatively simple technique to evaluate the tensile strength, yield strength and hardening exponent.

• Journal of the Korean Society for Heat Treatment
• /
• v.20 no.5
• /
• pp.237-242
• /
• 2007

Friction coefficient of SM45C steel was surprisingly reduced with $H_2S$ and $C_3H_8$ gas during plasma sulf-nitriding. During the plasma sulf-nitriding, 100-700 sccm of $H_2S$ gas and 100 sccm of $C_3H_8$ gas were added and working pressure and temperature were 2 torr, $500-550^{\circ}C$, respectively. As $H_2S$ gas amount increased over 500 sccm, flake-like structures were developed on top of the nitriding layer and grain size of the nitriding layer were about 100 nm. The friction coefficient for the sample treated plasma sulf-nitriding under $N_2-H_2S$ gas was 0.4 - 0.5. The structure became more finer and amorphous-like along with $N_2-H_2S-C_3H_8$ gas and the nano-sized surface microstructures resulted in high hardness and significantly low friction coefficient of 0.2.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5460-5466
• /
• 2014

In this study, mainly for kitchen knives and small swords, cutlery, etc. STS420J2 used material used for the experiments. In order to cure the surface of the test piece after the rough grinding and fine grinding was performed in order polishing. Perform the surface hardening of STS420J2 local area by using a diode laser. The output of the laser diode and the feed rate to the process variable. Micro-hardness testing, microstructure testing, scanning electron microscope testing(SEM), the heat input to the analysis. After analyzing the experiment to compare the mechanical properties of the material. When using a diode laser to assess the soundness of the surface hardening. Accordingly, the process for deriving the optimum demonstrate the feasibility.

• Journal of Powder Materials
• /
• v.12 no.6 s.53
• /
• pp.447-452
• /
• 2005

The synthesis and consolidation of titanium silicide by electro-discharge-sintering has been investigated. As-received Ti powder was in flaky shape and the mean particle size was $45.0{\mu}m$, whereas the mean particle size of the pre-milled Si powder with angular shape was $8.0{\mu}m$. Single pulse of 2.5 to 5.0 kJ/0.34g-elemental Ti and pre-milled Si powder mixture with the composition of $Ti-37.5at.\%$ Si was applied using $300{\mu}F$ capacitor. The solid with $Ti_5Si_3$ phase has been successfully fabricated by the discharge with the input energy more than 2.5kJ in less than $129{\mu}sec.$ Hv values were found to be higher than $1000kgf/mm^2$. The formation of $Ti_5Si_3$ occurred through a fast solid state diffusion reaction.

• Journal of the Korean Applied Science and Technology
• /
• v.19 no.1
• /
• pp.10-18
• /
• 2002

In this study, it should be mentioned that Lipid-LCG can be prepared with the main compound of hydrogenated lecithin in oil-in water emulsion. The results of its physical property and stability are as follows. First, the best suitable compositions of Lipid-LCG are made from 4.0wt% of the hydrogenated lecithin, 4.0wt% of cetostearyl alcohol as emulsifier and gelling agent, 3.0wt% of butylene glycol and 2.0wt% glycerin as moisturizers, 3.0wt% of cyclomethicone, 3.0wt% of isononyl-isononanoate, 3.0wt% of capric/caprylic triglycerides, 3.0wt% of macadamia oil as emollients. Second, As the optimum conditions to form Lipid-LCG, which figured out 6.0 ${\pm}$ 1.0 for pH level, 32kg/mm, min for hardness to make a .essence to be formed the ternary phase of liquid crystal(multi-lamellar type). Third, as the analytical result of this system, it obtained that particle size is $1{\sim}8{\mu}m$ level, and is certified with it at 400 and 1,000 magnifications by microscope. The stability of Lipid-LCG is very stable on condition of a low temperature ($4^{\circ}C$), a room temperature ($25^{\circ}C$) and a high temperature ($40^{\circ}C$), which is not to be split in for a long time(for 3-month). We produced our own moisturizing essence, which has a good affinity to skin by means of this system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.1620-1625
• /
• 2015

In this study, a variety of industrial gears, shafts, chains, rollers, mold, etc. are widely used inautomotive steel carbon steel for machine structural SM45C typical material used for the experiments. In order to cure the surface of the test piece after the rough grinding and fine grinding was performed in order polishing. Perform the surface hardening of SM45C lacal area by using a diode laser. The output of the laser diode and the feed rate to the process variable. Micro-hardness testing, microstructure testing, scanning electron microscope testing(SEM), the heat input to the analysis. After analyzing the experiment to compare the mechanical properties of the material. When using a diode laser to assess the soundness of the surface hardening. Accordingly, the process for deriving the optimum demonstrate the feasibility.