• 한국결정성장학회지
• /
• 제1권1호
• /
• pp.66-73
• /
• 1991

During the growth of macroscopically dislocation-free Czochralski silicon crystal, micro precipitates causing stacking faults in the silicon wafer during the oxidation are formed Thermal history the cryscausing acquire during the growth process is known to be a key factor determining the nucleation of this micro precipitates. In this article, various mechanisms suggested on the formation of microdefects in the silicon crystal are reviewed to secure the nucleation mechanism of the micro precipitates causing OSF whose pattern is normally ring or annular in CZ silicon crytal. B-defects which are known as vacancy clustering are considered to be the heterogeneous nucleation sites for the micro precipitates causing OSF in the CZ silicon crystals.

• International Journal of Internet, Broadcasting and Communication
• /
• 제15권1호
• /
• pp.145-149
• /
• 2023

In this study, the spectrum changes induced from the doping of phosphor micro particles in a twist nematic liquid crystal cell was observed. The experimental results show that the achromatic transmission can be observed with a proper driving condition, which may be applied to the design of an achromatic liquid crystal device. In this paper, we tried to figure out the spectrum changes induced from the doping of phosphor micro particles. The experimental result of the phosphor powder doped twist nematic liquid crystal cell shows that the achromatic transmission and the wavelength linearly dependent transmission both can be observed with some proper driving conditions, respectively. The result is useful on developing an achromatic liquid crystal device and it can be applied for Vihicle lamp.

• 한국결정성장학회지
• /
• 제15권6호
• /
• pp.229-233
• /
• 2005

Novel process was tried to obtain micro-porous ceramic body containing continuous pore channel. $MgAl_2O_4/MgO$ eutectic fibers and rods have been grown successfully by the micro-pulling-down method, and the microstructures and optical characterizations of grown crystals were performed. $MgAl_2O_4/MgO$ eutectic fibers of $0.3{\sim}1mm$ in diameter and about 500 mm in length, and the rods having 5 mm in diameter with approximately 60 mm in length have been grown with the $6{\sim}120mm/hr$ of growth speed. The eutectic fibers showed homogeneous microstructure in which MgO fiber aligned to the growth direction in the $MgAl_2O_4$ (spinel) matrix. The grown crystals looked semitransparency under naked eyes. Optical and orientational characterizations were performed. The second phase of MgO (periclase) was easily removed by selective etching with hydrochloric acid, and then porous bodies were obtained.

• 한국광학회지
• /
• 제16권2호
• /
• pp.113-120
• /
• 2005

LCD-BLU(liquid crystal device-back light unit)에 사용되는 도광판의 미세 산란패턴을 만드는 새로운 방법으로서, 실리콘 웨이퍼의 비등방 식각에 의해 자연적으로 형성되는 3차원 결정면 구조를 이용하는 방법을 제안하였다. 실리콘 3차원 결정면을 갖는 도광판과 프리즘 시트의 원판을 설계 및 제작하였고, casting 공정을 통해 PDMS 재질로 복제된 도광판을 제작하여 특성을 분석하였다. 측정 결과, 기존 인쇄형 도광판에 비해 실리콘피라미드 패턴의 도광판이 $10\%$ 증가된 정면 휘도 효율을 가질 수 있음을 실험적으로 검증하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.64-67
• /
• 2009

Vibrational micro-forming of pyramidal shape patterns was conducted for an Al superplastic alloy, Al 5083 and a Zr-based bulk metallic glass, $Zr_{62}Cu_{17}Ni_{13}Al_8$. A vibrational micro-forming system was specially designed for generating vibrational load by combining a PZT actuator with a signal generator. Single crystal Si micro dies with wet-etched pyramidal patterns were used as master dies for vibrational micro-forming. The micro-formed pattern height was increasing with increasing the frequency of the vibrational load. In particular, the vibrationally-microformed pattern height was similar or even higher than the statically-microformed pattern height when the load frequency exceeded about 125 kHz. It was also observed that the crystal grains affect the surface quality of the microformed pattern and the distribution of the pattern height in the die cavity array.

• 한국생산제조학회지
• /
• 제18권6호
• /
• pp.636-641
• /
• 2009

Recently, expansion of micro-technology parts requires micro-precision machining technology. Micro-groove machining is important to fabricate micro-grating lens and many micro-parts such as microscope lens, fluidic graphite channel etc. Conventional groove fabrication methods such as etching and lithography have some problems in efficiency and surface integrity. But, mechanical micromachining methods using single crystal diamond tools can reduce these problems in chemical process. For this reason, microfabrication methods are expected to be very efficient, and widely studied. This study deals with machinability in micro-precision V-grooves machining of nickel plated layer using non-rotational single crystal diamond tool and 3-axis micro stages. Micro V-groove shape, chip formation and tool wear were investigated for the analysis of machinability of Ni plated layer.

• 한국전기전자재료학회논문지
• /
• 제21권3호
• /
• pp.222-226
• /
• 2008

With different seed adhesion methods, we obtained two different aspects with or without micro-bubble in the interface between a seed and a dense graphite seed holder. To improve the quality of SiC wafer, we introduced a sucrose caramelizing step at the seed adhesion using the sucrose, The n-type 2 inch single crystal exhibiting the polytype of 6H-SiC were successfully fabricated and carrier concentration levels of about $10^{16}/cm^3$ was determined from Hall measurements, As compared to the characteristics of SiC crystal grown with micro-bubble in the interface between the seed and the dense graphite seed holder, the SiC crystal grown without micro-bubble definitely exhibited lower resistivity, lower micropipe density and higher mobility relatively.

• 한국결정성장학회지
• /
• 제9권3호
• /
• pp.267-272
• /
• 1999

Czochralski법으로 성장시킨 조화용융조성(48.6 mol%$LiNbO_3$)의 undoped 및 MgO-doped $LiNbO_3$ 단결정 내의 미소결함을 광학현미경 및 주사/투과 전자현미경을 이용하여 정밀분석하였다. Dopant 첨가 및 성장된 부위(g)에 따른 분역구조의 변화와 결함밀도를 측정함으로써 결함양상을 분석하고 최적 결정성장조건과의 상관관계를 고찰하였다. 강자성 분역벽 주변의 높은 결함밀도는 이 근처가 응력이 집중된 영역임을 반영하고, 특히 한쪽 방향의 분역벽에만 결함이 밀집된 결함구조를 가지고 있음을 확인하였다.

• 한국결정성장학회지
• /
• 제19권1호
• /
• pp.11-14
• /
• 2009

Micro-pulling down(${\mu}-PD$)법을 이용하여 직경 2mm, 길이 $15{\sim}25\;mm$의 Zn와 Yb가 첨가된 near-stoichiometric 조성의 $LiNbO_3$ 단결정을 성장하였다. 일정 직경의 매끄럽고 결함이 없는 양질의 단결정임을 확인하였고, 결정 내 첨가된 Zn와 Yb의 조성이 고루 분포되었음을 알 수 있었다. Raman spectra를 통해 나타난 모든 peak은 $LiNbO_3$ power의 peak과 일치함을 알 수 있었고, 이를 통해 Hexagonal 구조의 $LiNbO_3$가 성장되었음을 확인할 수 있었다. Zn의 첨가량 증가에 따른 IR 영역의 투과도 비교를 통해 광손상을 억제에 효과가 있는 Zn 첨가의 역치량이 1 mol%임을 알 수 있었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.910-911
• /
• 2006

We newly designed and manufactured a new arranging system for a three-dimensional artificial crystal of monosized micro particles. In this system, a robotic micro-manipulator accurately locates the spherical particle onto the lattice point, and subsequently fiber lasers micro-weld the contact points between the neighboring particles. Actually, one- and two-dimensional arrays were constructed using monosized tin particles with the diameter of 400 m. Moreover, due to optimization of the process parameters, we successfully constructed the artificial crystals of simple cubic and diamond structures. In particular, the diamond structure which can represent a large photonic band gap is expected to progress toward a practical photonic crystal device.