• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.137-140
• /
• 2005

The electronic dispenser is composed of electronic part and mechanical part. Electronic part is consisted of input keypad, micro-controller, display module, and pump module. In this paper we designed micro-controller for electronic part. The micro-controller controls display module and pump module. The display module is composed by LCD device, and the pump module is composed by motor device. The micro-controller for an electronic dispenser is designed by VHDL. We used WX12864APl for the LCD device and SPS20 for the stepping motor. Also, the micro-controller is designed by Altera Quartus tool and verified with Agent 2000 Design-kit using APEX20K Device. In this paper, we present possibility to adopt of biotechnology field through designing of one-chip controller for an electronic dispenser.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.148-152
• /
• 2003

This paper is concerned with the digital implementation of the active vibration suppression controller. The digital controllers are often implemented on the DSP board, which is very fast but expensive. There are many low-cost micro-controllers in the market but the feasibility of such micro-controllers for the active vibration suppression has never been conducted. In this study, we selected PIC 16F877 as a proper micro-controller for the digital implementation of the PPF controller. The circuit diagrams are explained in detail. Experimental results show that the low-cost micro-controller can be used as the active vibration controller.

• Journal of the Korea Society of Computer and Information
• /
• v.8 no.3
• /
• pp.163-169
• /
• 2003

This study was carried out develope a motor power change speed device of motor by used micro- controller. This system was producted a auto-change speed device which switching frequency was 1,000MHz by used a auto- controller. It had a continuous output current such as 5A, 11A, 25A, 35A, 50A. It used a variable voltage from 9V to 18V(Maximum). We designed hardware of and software of micro-controller, we are made up of a auto cut-off function by 3.7V for detected power-loss prevention.

• Proceedings of the KIPE Conference
• /
• 1996.06a
• /
• pp.56-59
• /
• 1996

In this paper, we developed a micro-stepping drive circuit of step motor and proposed software algorithm for parallel operation of step motors drived by micro-stepping circuit. Also, we implemented a parallel operation controller with a 16-bit micro-controller.

• Proceedings of the IEEK Conference
• /
• 2003.07d
• /
• pp.1395-1398
• /
• 2003

This paper presents a 32-bit RISC Micro-Controller which is useful in the dedicated DSP and communication areas. The designed processor has 5 stages pipeline architecture, and 28 instructions. This RISC Micro-Controller consist of 22,100 gates and has 5.95 ns data arrival time, and 437 ㎽ total dynamic power. The RISC Micro-Controller is a IP (Intellectual property) Core module which can implement a number of protocols by and is applicable to DSP and data communication.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.761-764
• /
• 1995

This paper demonstrates the feasibility of utilizing Shape Memory Alloy(SMA) actuators in controlling the motion of micro active catherer. The dynamic behavior of SMA is obtained by several experiments for the design of the controller. Two different type of structures which realize catheter are proposed. Each prototype of micro active catherer is fabricated, and its control performance which used the designed controller is investigated. The results obtained show the potential of the SMA as viable means for actuating the micro active catheter.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.15 no.4
• /
• pp.9-17
• /
• 2019

Sun power generation systems which use large capacity centralized inverters have loss of power generation due to cloud and building shadows, pollution, cell deterioration, etc. To minimize loss of power generation, decentralized solar power systems using multiple micro-inverters are being proposed as an alternative. A distributed solar power system consisting of a system-connected system uses power line communication to collect data from the micro-inverters. Power line communication has the advantage of using power lines without separate lines for data transmission, but in distributed solar power generation systems that use a large number of micro-inverters, the bit error rate is less reliable due to the phenomenon caused by limited transmission power, high load interference and noise, variable signal attenuation, and impedance characteristics. So we proposed wireless intelligent controller for micro-inverter that is used to build distributed solar power systems. and we design and implement that. Further, the proposed wireless intelligent controller for micro-inverter was used to establish a small-volume solar power plant to check its function and operation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.2
• /
• pp.164-170
• /
• 2004

Recently, the demand for micro hard disk drive that provides high-capacity removable storage for handhold electronic devices is growing very rapidly Reducing power consumption is one of the primary control objectives in micro disk drives. The input power delivered to the seek servo system is consumed as heat by the transistors of power amplifier and motor coil resistance. In this paper, we present a new seek servo controller for minimizing the power consumption. We use a Fourier decomposition and nonlinear programming to determine the optimum seek profile that minimizes the power consumption. Also, the trajectory tracking controller is developed for exact tracking of the optimum seek profile. Finally, we present some experimental results using a commercially available micro disk drive in order to demonstrate the superior performance of the proposed controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10b
• /
• pp.1327-1331
• /
• 1990

A new dual loop controller using color LCD bar graphs with LED back lights has been developed. An optional memory card is used to load or save the controller configuration, which may be a preprogrammed standard package or a user-programmed configuration, in addition to the built-in functions ready for user selection. The bar-graph display is selectable for single-loop or dual-loop use. A high grade of self-tuning functions using a modeling technique is built-in as standard. The controller can accommodate optional plug-in modules for thermocouples, communication, etc. All the options are fully field upgradable.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.53 no.4
• /
• pp.166-170
• /
• 2004

In this paper, it has been proposed the simultaneous control of PFC (power factor corrector) and electronic ballast for fluorescent lamp by one chip micro-controller. Boost DC-DC converter is adopted for PFC, and half bridge inverter for electronic ballast. It controls, simultaneously and independently, the boost DC-DC converter and the half bridge inverter. As PFC and electronic ballast are controlled by one chip micro-controller, it is possible to achieve the simpler and the cheaper controller for fluorescent lamp. Experimental results have shown the feasibility of the proposed simultaneous control of PFC and electronic ballast by one chip micro-controller.