• Journal of the Korean Ceramic Society
• /
• v.34 no.7
• /
• pp.677-684
• /
• 1997

The effects of fluxes on MgO coating materials for tundish were investigated. As the number of charge in continuous casting was increased, the basicity of tundish slag was decreased due to the increase of silica formed by dissolution from rice hull. As a result, the wear of magnesia lining was increased. In aggregates of MgO coating materials, magnesioferrite was formed by the reaction between magnesia and ferric oxide formed by the oxidation of molten steel, while matrix parts of MgO coating materials were worn by CaO-Al2O3-SiO2 compounds. Silica in rice hull extracted to the molten slag reduced basicity of slag and formed forsterite in the result of its reaction with magnesia lining. Also, fayalite was formed from the reaction between silica and ferric oxide and it caused the increment of magnesia lining's wear. The wear of magnesia lining by flux of CaO-SiO2 was larger than that of Cao-Al2O3 and calcia in the flux increased the wear of magnesia lining through the formation of rankinite.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.9
• /
• pp.960-966
• /
• 2004

On the bases of the results from "Additive Coating of BaTiO$_3$ Powder using Sol Coating Method I", experimental condition was defined. Representative additives for BaTiO$_3$, that is to say, Mg, Ca and Mn were experimented. The sources of the metal ion were used by organometal complex. As added it, the stability of BaTiO$_3$ sol was evaluated. Mg and Ca were stable, however, The solubility limit of Mn-ATH was 0.05 mol ratio in Mn-ATH/sol. The solubility limit of Mg ion in BaTiO$_3$ was lower than 2 mol%. From the x Ray diffraction patterns, lattice parameters were different with temperature and additives, because the solubility of metal ion was varied in BaTiO$_3$. The dielectric constant of BaTiO$_3$ powders which coated with the 1.5 mol% Mg and calcined at 1200$^{\circ}C$ was increased with 20%.

• Journal of the Korean Ceramic Society
• /
• v.46 no.2
• /
• pp.189-199
• /
• 2009

The Powder characteristics and sintering behavior of $SiO_2$ coated $BaTiO_3$ were studied. $BaTiO_3$ powders were synthesized by the liquid mix method developed by Pechini, and silica coating was prepared by alkoxide hydrolysis method with TEOS and ethanol. The particle size of the $BaTiO_3$ powders was 35 nm and the thickness of the $SiO_2$ coating layer was 5 nm. As the $SiO_2$ content increased, the $SiO_2$ layers improved the powder dispersion by increasing electrostatic repulsion between the $BaTiO_3$ particles. Effects of MgO coating on microstructure and dielectric properties of $BaTiO_3$ have been studied compared with mechanically MgO mixed $BaTiO_3$. MgO coated $BaTiO_3$ particles were prepared by a homogeneous precipitation method using $MgCl_2\cdot 6H_2O$ and urea. MgO coated $BaTiO_3$ exhibited homogeneous microstructure compared with mixed samples. XRD analysis revealed that Mg substitution for the Ti site in the MgO mixed sample was much greater than in the coated one. Electrical properties of MgO mixed and coated $BaTiO_3$ were affected by the diffusion behavior of Mg in $BaTiO_3$ lattice.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.10
• /
• pp.447-450
• /
• 2003

This paper presents a process optimization of antireflection (AR) coating on crystalline Si solar cells. Theoretical and experimental investigations were performed on a double-layer AR (DLAR) coating of MgF$_2$/CeO$_2$. We investigated CeO$_2$ films as an AR layer because they have a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. RF sputter grown CeO$_2$ film showed strong dependence on a deposition temperature. The CeO$_2$ deposited at 40$0^{\circ}C$ exhibited a strong (111) preferred orientation and the lowest surface roughness of 6.87 $\AA$. Refractive index of MgF$_2$ film was measured as 1.386 for the most of growth temperature. An optimized DLAR coating showed a reflectance as low as 2.04% in the wavelengths ranged from 0.4${\mu}{\textrm}{m}$ to 1.1${\mu}{\textrm}{m}$. We achieved the efficiencies of solar cells greater than 15% with 3.12% improvement with DLAR coatings. Further details on MgF$_2$, CeO$_2$ films, and cell fabrication parameters are presented in this paper.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.593-596
• /
• 1999

This paper presents a process optimization of antireflectiun (AR) coating on crystalline Si solar cells. Theoretical and experimental investigations were performed on a doble-layer AR(DLAR) coating of MgF$_2$/CeO$_2$, We investigated CeO$_2$ films as an All layer because they hale a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. RF sputter grown CeO$_2$ film showed strong dependence on a deposition temperature. The CeO$_2$ film deposited at 400 $^{\circ}C$ exhibited a strong (111) preferred orientation and the lowest surface roughness of 6.87 $\AA$. Refractive index of MgF$_2$ film was measured as 1.386 for the most of growth temperature. An optimized DLAR coating showed a reflectance as low as 2.04 % in the wavelengths ranged from 0.4 7m to 1.1 7m. We achieved the efficiencies of solar cells greater than 15% with 3.12 % improvement with DLAR coatings . Further details on MgF$_2$, CeO$_2$ films, and cell fabrication Parameters are presented in this paper.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1288-1289
• /
• 2006

Innovative SMC with low iron loss was made from iron powders with evaporated MgO insulation coating. The coating had greater heat-resistance than conventional phosphatic insulation coating, which enabled stress relieving annealing at higher temperature. Magnetic properties of toroidal samples (OD35mm,ID25mm, t5) were examined. The iron loss at 50Hz for Bm = 1.5T was lower 50% of conventional SMC and was almost the same with silicon iron laminations(t0.35). It became clear that MgO insulation coating has enough heat resistance and adhesiveness to powdersurface to obtain innovative SMC with low iron loss.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.7
• /
• pp.621-625
• /
• 1996

A variety of metal oxides were coated by sol-gel process from their metal alkoxides on the ribbons of Co-based and Fe-based amorphous alloys, and the effects of surface oxide coating on the magnetic properties of the alloy are investigated. The core loss is found to be reduced significantly by the oxide coating, the loss reduction becoming more prominent at higher frequencies. The shape of the hystersis loop is also dependent upon the kind of the coated metal oxide. The coatings of MgO, SiO2, MgO·SiO2 and MgO·Al2O3 induce tensile stress into the Fe-based ribbon whereas those of BaO, Al2O3, CaO·Al2O3, SrO·Al2O3 and BaO·Al2O3 induce compressive stress. These results may be explained by the modification of domain structures via magnetoelastic interactions with the shrinkage stress induced by the sol-gel coating.

• Progress in Superconductivity
• /
• v.3 no.2
• /
• pp.188-192
• /
• 2002

To introduce flux pinning center in HTS-BSCCO system, nano-size MgO particles were uniformly distributed within the Bi-2223 grain by partial hydration of MgO. The existing method MgO doped Bi-2223 used nato-size MgO powders, which resulted in agglomeration during mixing or grain growth during heat-treatment due to the high surface energy of the fine particles. By hydration of the MgO surface, the agglomeration of the MgO powders was avoided and the size of remaining MgO core was controlled by changing hydration medium and time. The thin film obtained by spin coating of (Bi_$1.8/Pb_{0.4}$)$Sr_2$$_{Ca}$$2.2/Cu_3$ $O_{y}$ nitrate solution mixed with hydrated MgO showed the even distribution of nano-size MgO particles in the Bi-2212 grains.s.s.

• Journal of Korea Foundry Society
• /
• v.5 no.3
• /
• pp.19-26
• /
• 1985

This study has been carried out to examine into wettability of Cu-5%Sn alloy in $Al_2O_3$, MgO, $SiO_2$ and graphite, respectively and investigated into the change in macrostructure of Cu-5%Sn alloy according to kind and mixing rate of mold-coating. The results obtained from the experiment are summerized as follows; 1. Cu Cu-5%Sn alloy, wettabilities of $Al_2O_3$ and MgO were good, on the other hand, wettabilities of $SiO_2$ and graphite were bad. 2. The fine equiaxed zone was created because of the role of $Al_2O_3$ and MgO as preferential nucleation sites. 3. Notwithstanding change of mixing rate of $SiO_2$ in mold coating the equixed zone was not created. 4. The area of equiaxed zone was varied according to mixing rate in the case of using $Al_2O_3$ and MgO in mold-coating.

• Korean Journal of Materials Research
• /
• v.18 no.5
• /
• pp.241-246
• /
• 2008

Pure Mg and Mg-6wt.%Al alloy were coated by the plasma electrolytic oxidation with various coating times and the microstructural and mechanical characteristics of the coatings were investigated. The coatings on pure Mg and Mg-6wt.%Al alloy consisted of MgO and $Mg_2SiO_4$. The surface roughness and thickness of the coatings became larger as the coating time increased. The coatings on the Mg-6wt.%Al alloy were more uniform and thicker than those on pure Mg. The microhardness and friction coefficient of the coatings increased progressively as the coating time increased. In addition, the coatings on the Mg-6wt.%Al alloy compared to pure Mg showed improved microhardness and a better friction coefficient.