• 열처리공학회지
• /
• 제3권1호
• /
• pp.8-16
• /
• 1990

Effects of thermomechanical treatments(TMT) on the microstructures and mechanical properties in Al-2.27%, Li-1.28%, Cu-0.63%, Mg-0.12%, Zr alloy were investigated. The TMT process improved the tensile strength. Growth of ${\delta}^{\prime}$, S' and $T_1$ phases was restrained by TMT processes while the density of ${\delta}^{\prime}$, S' and $T_1$ phases was increased by TMT processes. The TMT treated specimens tend to fail in inter-subboundary mode. The increases of strength by the T-HA processes were compared to those of the T-AHA processes.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1264-1265
• /
• 2006

Study about the feasibility and effect of high-energy ball milling on a specific Mg alloy under protection medium of alcohol was presented via comparing with conventional vacuum milling. More fine particles with wider powder size distribution but more irregular shape were shown of the powder milled under alcohol. No obvious oxide was revealed from the two kinds of Mg alloy powders with limited milling time. And since slip induced in a preferential direction, the (002) texture was formed in the Mg alloy powders at the initial stage of alcohol milling. More O and Fe contaminants were introduced into the powders milled under alcohol according to the EDS analysis.

• 한국주조공학회지
• /
• 제17권3호
• /
• pp.267-275
• /
• 1997

Fabrication of high strength Mg-Li-Al alloys by squeeze casting was established by the stabilization of melt and mold temperatures, applied pressure and the refining method. The entrapment of inclusions during pouring was prevented using 30 ppi alumina foam filter. The as-cast microstructure consists of a mixture of ${\alpha}$ and ${\beta}$ phases including AILi and $MgLi_2$, Al particles, which are distributed in the ${\beta}$ matrix. The grain sizes of gravity and squeeze casting alloys were 288 ${\mu}m$ and 207 ${\mu}m$ respectively. The addition of Al in Mg-Li alloys promoted the formation of second phase particles, which were adjusted to optimize the properties of Mg-Li-Al alloys. The Mg-10wt%Li-5wt%Al alloy after heat treatment at $350^{\circ}C$ for 1 hour showed the maximum hardness value. This is due to the facts that the amounts of ${\alpha}$ and ${\beta}$ phases and their distributions are dependent upon the solution treatment temperature, and that the amounts of AILi and $MgLi_2Al$ particles are dependent upon the Al content.

• 한국재료학회지
• /
• 제6권9호
• /
• pp.925-930
• /
• 1996

Zr이 0.03wt%함유된 Mg-8.14Li-3.93AI 합금의 시효거동을 미소경도와 미세조직의 변화, 열분석 등으로 조사하였다. Zr의 첨가로 인하여 3원계 Mg-8.23Li-4.02A에 비하여 조직이 미세화되었으며 모든 시효조건에서 경도값이 높게 나타났다. 열분석결과 발열피크는 준안정 석출상인 MgLi2AI($\theta$)의 석출과 $\theta$상에서 안정상인 AILi으로의 변화와 관련된 것이고, 흡열피크는 $\theta$와 AILi상의 재용해에 대응되는 것으로 판단되었다. 피크 경도값(103Hv)은 $\theta$의 석출이 완료되는 393K에서 0.5시간 시효시 나타났으며 피크 경도조건에서의 미세조건은 $\beta$기지에 $\theta$와 AILi상이 공존하고 있음을 투과식 전자현미경으로 확인하였다.

• 한국재료학회지
• /
• 제21권6호
• /
• pp.314-319
• /
• 2011

Melt foaming method is one of cost-effective methods to make metal foam and it has been successfully applied to fabricate Mg foams. In this research, AZ31 Mg alloy ingot was used as a metal matrix, using AlCa granular as thickening agent and $CaCO_3$ powder as foaming agent, AZ31 Mg alloy foams were fabricated by melt-foaming method at different foaming temperatures. The porosity was above 41.2%~73.3%, pore size was between 0.38~1.52 mm, and homogenous pore structures were obtained. Microstructure and mechanical properties of the AZ31 Mg alloy foams were investigated by optical microscopy, SEM and UTM. The results showed that pore structure and pore distribution were much better than those fabricated at lower temperatures. The compression behavior of the AZ31 Mg alloy foam behaved as typical porous materials. As the foaming temperature increased from $660^{\circ}C$ to $750^{\circ}C$, the compressed strength also increased. The AZ31 Mg alloy foam with a foaming temperature of $720^{\circ}C$ had the best energy absorption. The energy absorption value of Mg foam was 15.52 $MJ/m^3$ at a densification strain of 52%. Furthermore, the high energy absorption efficiencies of the AZ31 Mg alloy foam kept at about 0.85 in the plastic plateau region, which indicates that composite foam possess a high energy absorption characteristic, and the Vickers hardness of AZ31 Mg alloy foam decreased as the foaming temperature increased.

• 열처리공학회지
• /
• 제9권2호
• /
• pp.103-111
• /
• 1996

In this paper, we studied on both electrochemical polarization behaviors and pitting characteristics of ultra high strength Al-Cu-Li-Mg-Ag-Zr alloys(named C1 and C2) and 2090 alloy according to their treatments in the deaerated 3.5% NaCl, using by the potentiodynamic and the potentiostatic method, SEM micrograph and surface roughness including depth of pitting attack. With the cyclic polarization curves, the hysteresis of the C1 and C2 alloys appeared more remarkably than that of the 2090 alloy, because of precipitation microstructural difference between C1, C2 alloys and 2090 alloy. In the pitting experiments, the correlations between pitting growth and aging conditions were analyzed with the SEM micrograph and measurement of the pit depth.

• 열처리공학회지
• /
• 제7권2호
• /
• pp.77-87
• /
• 1994

Roles of fundamental and additional hardening precipitates on the changes of mechanical properties and electrical resistivity during precipitation decomposition in binary Al-Li, ternaty Al-Li-Cu and multi-Li-Cu-Mg-Zr alloys have been investigated by the detailed measurement of electrical resistivity, hardness and tensile strength and the observation of transmission electron micrographs. Peek hardness and tensile strength in multi-component Al-Li-Cu-Mg-Zr Alloy had higher than that of the other alloys and the results of measurement of hardness, strength and electrical resistivity in each alloys aged at 90 and $190^{\circ}C$, precipitation behaviors and mechanical properties in binary, ternary and multi-component Al-Li alloys were contributed to the ${\delta}^{\prime}$ precursory phase of ${\delta}^{\prime}$, $T_1$, G.P.B. zone and S' phases, repectively.

• 열처리공학회지
• /
• 제4권2호
• /
• pp.38-46
• /
• 1991

Effects of aging treatment on the microstructures and microhardness of a rapidly solidified Al-Li-Cu-Mg-Zr alloy were investigated by differential scanning calorimetry(DSC) and transmission electron microscopy(TEM). The as-melt-spun ribbon was consisted of fine ${\delta}^{\prime}$ and icosahedral intermetallic compound which were precipitated in the matrix. Two exothermic peaks with the range of $120^{\circ}C-190^{\circ}C$ and $280^{\circ}C-344^{\circ}C$ corresponded to ${\delta}^{\prime}$ and ${\theta}^{\prime}$, S', $T_1$ precipitating reaction respectively, and two endothermic peaks with the range of $190^{\circ}C-280^{\circ}C$ and $344^{\circ}C-550^{\circ}C$ corresponded to dissolution of ${\delta}^{\prime}$ and ${\theta}^{\prime}$, S', $T_1$ respectively in DSC curves. Peak hardness value was obtained at $210^{\circ}C$ for 1 hr aging treatment.

• 열처리공학회지
• /
• 제5권1호
• /
• pp.41-49
• /
• 1992

The effects of alloying elements on the superplastic properties of Al-Li based alloys had been investigated. The intermediate thermo-mechanical treated (ITMT) Al-2.0wt%Li, Al-2.0wt%Li-1.0wt%Mg, Al-2.0wt%Li-0.12wt%Zr and Al-2.0wt%Li-1.2wt%Cu-1.0wt%Mg-0.12wt%Zr alloys were tested in tension at various temperature (400, 450, 500 and $550^{\circ}C$) and strain rate($6.7{\times}10^{-3}$, $1.0{\times}10^{-2}$, $1.6{\times}10^{-2}$ and $5.0{\times}10^{-2}/sec$). The results were as follows : The superplasticity in binary, ternary and pentanary alloys appeared at 500 to $550^{\circ}C$, and good strain rate for superplasticity. $1.6{\times}10^{-2}/sec{\sim}1.0{\times}10^{-2}/sec$ for a binary alloy and $1.0{\times}10^{-2}/sec{\sim}6.7{\times}10^{-3}/sec$ for ternary and pentanary alloys. A Zr-added ternary alloy had best value of elongation (730%) in four alloys at $550^{\circ}C$ of tension temperature and $1.0{\times}10^{-2}/sec$ of strain rate. The strain rate was greatly dependent on tension temperature and true strain rate was more than 1.0 at all test temperature and strain rate. In binary and Mg-added teranry alloys. the necks were slightly formed and their fracture surface had lips shape, but Zr-added ternary and pentanary alloy fractured along the grain boundary without necking. Their dislocations moved to grain boundary during superplasticity deformation and arranged perpendicular to grain boundary. Super plastic deformation was made by grain boundary slip of dislocation slip creep and model of core and mantle.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2018년도 춘계학술논문요약집
• /
• pp.106-107
• /
• 2018