• Journal of Korea Foundry Society
• /
• v.6 no.2
• /
• pp.93-103
• /
• 1986

It is very important to obtain wear resistant ductile iron by adding more economical alloying elements. In this study, 10 heat of Mg-treated ductile iron were made according to Sb content (0-0.1% Sb). Each melt was tasted to 30 ${\o}test$ bars in $CO_2$ mold under the same condition and inspected wear characteristics, mechanical properties and microstructures. The results obtained from this study are as follows; 1. It is confirmed that Sb should be a simple and useful additive for improving wear resistance in ductile iron. 2. Hardness of ferrite and pearlite is improved with increasing Sb amount in ductile iron. 3. For ductile iron, the recommended ladle addition of Sb amount is to 0.02-0.03%. 4. Sb has adverse influence on spheroidizing of graphite if the amount is over 0.04%.

• Journal of the Korean Society of Safety
• /
• v.14 no.1
• /
• pp.49-54
• /
• 1999

In this paper. we studied cut off characteristics and fire hazard of residual current protective devices(RCD or ELB) for low voltage. The operative time of RCD with grounding resistance was analyzed by using RCD operating tester. The surface structure and composition of insulator were analyzed by using scanning electron microscope(SEM) and energy dispersive x-ray spectroscopy(EDX). The surface of phenol resin showed network structure and void. The spectra shown in EDX analysis are composed not only of the corresponding elements but also of several new spectra, as CK. OK$\alpha$. MgK, SiK. and CaK, which were absent in original material.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.225-228
• /
• 2000

Addition effects of metal oxide on the characteristics of infrared radiator of porous cordierite have been investigated. The porosity was increased with adding the graphite for 2MgO $.$ 2A1$_2$O$_3$$.$5SiO$_2$. The microstructure and the spectral emissivity were investigated as a function of metal oxide additives. The prosity and the emissivity were decreased with increasing amounts of CuO additives. The prosity and the emissivity were increased with increasing amounts of CoO, MnO$_2$ additives. The infrared radiator of cordierite system which spectral emissivity was 0.927 and 0.928 at from 5$\mu\textrm{m}$ to 20$\mu\textrm{m}$ wavelength as a 9wt% of CoO and MnO$_2$ additives.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1379-1385
• /
• 2018

The hand held voltammetry systems searched diabetic assay using glucose sensor of fluorine nafion doped carbon nanotube electrode (FCNE). An inexpensive graphite carbon pencil was used as an Ag/AgCl reference and Pt counter electrode. Upon combining and using three electrode systems, optimum square wave (SW) stripping results were attained to 1.0-9.0 ug/L with 8 points. Statistic RSD precision was of 6.02 % with n=15 in 0.1 mg/L glucose. After a total of 200 second accumulation times, analytical detection limit of 0.8 ug/L was obtained. This developed technique was applied to urine samples from diabetic patients urine for fluid analysis, it was determined that the sensor can be used with a diagnostics in the ex vivo of live cells and non treated biological fluid.

• Resources Recycling
• /
• v.31 no.6
• /
• pp.44-51
• /
• 2022

In the steelmaking process using an electric arc furnace (EAF), light-burnt dolomite, which is a flux containing MgO, is used to protect refractory materials and improve desulfurization ability. Furthermore, a recarburizing agent is added to reduce energy consumption via slag foaming and to induce the deoxidation effect. Herein, a waste MgO-C based refractory material was used to achieve the aforementioned effects economically. The waste MgO-C refractory materials contain a significant amount of MgO and graphite components; however, most of these materials are currently discarded instead of being recycled. The mass recycling of waste MgO-C refractory materials would be achievable if their applicability as a flux for steelmaking is proven. Therefore, experiments were performed using a target composition range similar to the commercial EAF slag composition. A pre-melted base slag was prepared by mixing SiO₂, Al₂O₃, and FeO in an alumina crucible and heating at 1450℃ for 1 h or more. Subsequently, a mixed flux #2 (a mixture of light-burnt dolomite, waste MgO-C based refractory material, and limestone) was added to the prepared pre-melted base slag and a melting reaction test was performed. Injecting the pre-melted base slag with the flux facilitates the formation of the target EAF slag. These results were compared with that of mixed flux #1 (a mixture of light-burnt dolomite and limestone), which is a conventional steelmaking flux, and the possibility of replacement was evaluated. To obtain a reliable evaluation, characterization techniques like X-ray diffraction (XRD) analysis and X-ray fluorescence (XRF) spectrometry were used, and slag foam height, slag basicity, and Fe recovery were calculated.

• Membrane Journal
• /
• v.28 no.4
• /
• pp.271-278
• /
• 2018

In this study, the carbon electrodes using activated carbon fibers (ACFs) were prepared for the capacitive deionization process. The Polyvinylidene fluoride (PVDF) was used as the binder and the mixed ACFs with proper solvent was cast on the commercial graphite sheets to prepare the carbon electrodes. At this moment, the different particle sizes of ACFs were applied and the mixing ratio of solvent, PVDF and ACFs, 80 : 2 : 18 and 80 : 5 : 15, were used for the electrode preparation. Then their salt removal efficiencies were characterized under the various operating conditions, adsorption potential and time, desorption potential and time, concentration of feed NaCl solution and flow rate as well. Typically, the salt removal efficiency of 53.6% were obtained at the particle size below $32{\mu}m$, mixing ratio 80 : 2 : 18, adsorption 1.2 V and 3 min, desorption -0.1V and 1 min, and 15 mL/min flow rate of NaCl 100 mg/L.

• Korean Journal of Materials Research
• /
• v.24 no.5
• /
• pp.243-248
• /
• 2014

Silicon-carbon composite was prepared by the magnesiothermic reduction of mesoporous silica and subsequent impregnation with a carbon precursor. This was applied for use as an anode material for high-performance lithium-ion batteries. Well-ordered mesoporous silica(SBA-15) was employed as a starting material for the mesoporous silicon, and sucrose was used as a carbon source. It was found that complete removal of by-products ($Mg_2Si$ and $Mg_2SiO_4$) formed by side reactions of silica and magnesium during the magnesiothermic reduction, was a crucial factor for successful formation of mesoporous silicon. Successful formation of the silicon-carbon composite was well confirmed by appropriate characterization tools (e.g., $N_2$ adsorption-desorption, small-angle X-ray scattering, X-ray diffraction, and thermogravimetric analyses). A lithium-ion battery was fabricated using the prepared silicon-carbon composite as the anode, and lithium foil as the counter-electrode. Electrochemical analysis revealed that the silicon-carbon composite showed better cycling stability than graphite, when used as the anode in the lithium-ion battery. This improvement could be due to the fact that carbon efficiently suppressed the change in volume of the silicon material caused by the charge-discharge cycle. This indicates that silicon-carbon composite, prepared via the magnesiothermic reduction and impregnation methods, could be an efficient anode material for lithium ion batteries.

• Carbon letters
• /
• v.22
• /
• pp.42-47
• /
• 2017

In this paper, the in vitro biocompatibility of graphene film (GF) with osteoblasts was evaluated through cell adhesion, viability, alkaline phosphatase activity, F-actin and vinculin expressions, versus graphite paper as a reference material. The results showed that MG-63 cells exhibited stronger cell adhesion, better proliferation and viability on GF, and osteoblasts cultured on GF exhibited vinculin expression throughout the cell body. The rougher and wrinkled surface morphology, higher elastic modulus and easy out-of-plane deformation associated with GF were considered to promote cell adhesion. Also, the biomineralization of GF was assessed by soaking in simulated body fluid, and the GF exhibited enhanced mineralization ability in terms of mineral deposition, which almost pervaded the entire GF surface. Our results suggest that graphene promotes cell adhesion, activity and the formation of bone-like apatite. This research is expected to facilitate a better understanding of graphene-cell interactions and potential applications of graphene as a promising toughening nanofiller in bioceramics used in load-bearing implants.

• Journal of the Korean Ceramic Society
• /
• v.43 no.10 s.293
• /
• pp.646-652
• /
• 2006

Several oxynitride glasses were fabricated by means of adding $Si_3N_4$ powders as nitrogen source to Ca-Al-Si-O-N (CAS) and Mg-Al-Si-O-N (MAS) glass powders, and heat-treated in graphite crucible at 1600$^{\circ}C$ for 1 h. The physical and mechanical properties as well as impact resistance were generally increased and compared with each other. The impact resistance properties of those manufactured glasses were evaluated by DOP (depth of penetration) method which is a way to analyze armor materials. There were two means to be used herein; the copper jet impacted at hyper velocity by exploding K2l5 warhead and tungsten heavy alloy (WHA) impact bar at high velocity by firing in 30 mm solid propellent gun. The impact resistance properties against copper jet were increased and then decreased with increasing nitrogen content, while those against WHA bar were not changed apparently with nitrogen content.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.04a
• /
• pp.438-441
• /
• 2003

남해 동부 연안 지역 지하수의 해수 침투 영향을 광역적으로 파악하기 위하여, 202개소의 지하수 시료를 채취하고 수리지구화학적 연구를 수행하였다. 전체 시료 중 14.4%가 500 $\mu\textrm{m}$/cm을 초과하는 높은 EC값을 나타내어 해수 영향을 시사해 주었다. 해수 영향 판단의 또 다른 파라메터로 사용되는 CI/HCO$_3$ 몰비는 전체 시료의 23.3%가 1.3 이상의 값을 나타내었다. 한편, 대표적으로 해수침투 영향 및 인위적 오염의 영향을 각각 반영하는 것으로 알려진 Cl과 NO$_3$의 농도에 관한 누적도수분포도를 작성하여 배경수질군과 오염영향군을 구분짓는 배경치(background concentration)를 구한 결과, 각각 Cl = 22.3 mg/1 및 NO$_3$= 23.1 mg/l로 나타났다. 이 두 파라메터의 농도 분포를 기준으로 하여 채취된 지하수 시료를 크게 4개의 그룹으로 나눌 수 있었다. 그 결과, 자연적 또는 인위적 기원의 오염이 배제된 그룹 1은 전체 시료의 31%, 자연적 오염(해수 영향)을 반영하는 그룹 2는 전체의 24%, 인위적 오염의 영향을 반영하는 그룹 3은 전체의 9%, 해수 영향 및 인위적 오염을 동시에 반영하는 그룹4는 전체의 36%로 나타났다. 또한 그룹2와 그룹4는 대부분 Na-Cl유형으로 진화하는 Ca-Cl유형을 나타내었다. 따라서, 여러 지구화학 방법에 의한 해수 영향 판단 결과는 서로 잘 일치하고 있음을 알 수 있다. 결국, 지구화학적 파라메터를 종합적으로 활용함으로써, 연안 지역 해수침투의 효과적인 파악은 물론 예측 및 방지, 복구에 효과적으로 사용될 수 있을 것으로 판단된다.으로 토양에서 유동 가능성이 있는 중금속만을 추출하였다. 분석실험은 토양의 Cd2+ 와 Pb2+를 대상으로 행하여졌으며, 여러 토양에서 추출 분석한 결과를 EDTA분석결과와 비교하였다. 실험결과, 중금속은 매우 신속하게 고분자 자성체와 결합하였고, 그 후 자성체를 외부 자장으로 모은 후 산으로 용해시키고, 결합된 중금속은 Graphite furnace AAS로 분석함으로써 빠르고 효율적으로 분석실험을 수행할 수 있음을 알 수 있었다. 한편, 실험에서 나타난 수치들을 비교 검토한 결과 토양 분석시 sandy soil에서는 자성체를 이용한 분석이 EDTA에 의한 방법보다 더 높은 추출도를 보인 반면, silt 함량이 많은 토양의 경우에서 EDTA분석에서 더 높은 중금속 추출도를 보였다.s 중에서 490nm와 555nm의 복합밴드를 포함하는 OC2 알고리즘(ocean color chlorophyll 2 algorithm)을 사용하는 것이 OC2 series 및 OC4 알고리즘보다 좋은 추정 값을 도출할 수 있을 것으로 기대된다.환경에서는 5일에서 7월에 주로 이 충체의 유충이 발육되고 전파되는 것으로 추측되었다.러 가지 방법들을 적극 적용하여 금후 검토해볼 필요가 있을 것이다.잡은 전혀 삭과가 형성되지 않았다. 이 결과는 종간 교잡종을 자방친으로 하고 그 자방친의 화분친을 사용할 때만 교잡이 이루어지고 있음을 나타내고 있다. 따라서 여교잡을 통한 종간잡종 품종육성 활용방안을 금후 적극 확대 검토해야 할 것이다하였다.함을 보이고 있다.X> , ZnCl$_{3}$$^{-}$같은 이온과 MgCl$^{+}$, MgCl$_{2}$같은 이온종을 형성하기 때문인것 같다. 한편 어