• Journal of radiological science and technology
• /
• v.23 no.1
• /
• pp.97-101
• /
• 2000

In this study, the highly sensitive $CaSO_4:Tm$-PTFE TLDs has been fabricated for the purpose of measurement of high energy electron. $CaSO_4:Tm$ phosphor powder was mixed with polytetrafluoroethylene(PTFE) powder and moulded in a disk type(diameter 8.5 mm. thickness $90\;mg/cm^2$) by cold pressing. The absorbed dose distribution and ranges for high energy electron were measured by using the $CaSO_4:Tm$-PTFE TLDs. The ranges determined were $R_{100}=14.5mm$, $R_{50}=24.1mm$ and $R_P=31.8mm$, respectively and the beam flatness, the variation of relative dose in 80% of the field size, was 4.5%. The fabricated $CaSO_4:Tm$-PTFE TLDs nay be utilized in radiation dosimetry for personal, absorbed dose and environmental monitoring.

• Applied Microscopy
• /
• v.52
• /
• pp.12.1-12.8
• /
• 2022

The microstructure of diatom frustules found in mud sediments along the coast of Boryeong- city, South Korea, was observed using a scanning electron microscopy (SEM), and the constituent elements of diatoms were analyzed using energy-dispersive X-ray spectroscopy (EDS). Diatom frustules and clay minerals were present in the SEM images of the mud powder. High-magnification SEM images revealed that the surface of the frustules contained identically shaped circular pores, measuring 1 ㎛ in diameter, arranged at regular intervals. This study revealed that the diatom shell fragments in the mud powder ranged in size from 3 to 30 ㎛, with an average thickness of approximately 2.5 ㎛. The elements Si, Al, Fe, K, Na, Mg, and Ti were detected while analyzing the frustule constituents, with Si being the primary component with the highest content.

• Korean Journal of Mineralogy and Petrology
• /
• v.36 no.3
• /
• pp.213-220
• /
• 2023

In this study, we report the effect of starting materials on the grain size in a multi-component system at high pressure experiments. We used two different starting materials, glass and nano powders, to synthesize bridgmanite in the reduced conditions in the presence of calcium-ferrite-phase MgAl₂O₄ to compared the grain size of synthesized samples. After synthesizing the sample at 40 GPa, 2000 K for 20 hrs, the sample from glass showed the grain size of 50-200 nm whereas the one from nano powders has ~500 nm of grains. This difference may come from 1) the temperature of 2000 K which is low enough for glass starting materials to make more crystal nucleis than to grow crystal size or 2) the possible difference in the redox state of starting materials. It is suggested that the using of nano powders is better to synthesize bigger grains in high pressure experiments with multi-component systems rather than using glass starting materials.

• Journal of the Korean Ceramic Society
• /
• v.50 no.3
• /
• pp.226-230
• /
• 2013

We performed high pressure high temperature (HPHT) sintering for the 20 nm MgO powders at the temperatures from $600^{\circ}C$ to $1200^{\circ}C$ for only 5 min under 7 GPa pressure condition. To investigate the microstructure evolution and physical property change of the HPHT sintered MgO samples, we employed a scanning electron microscopy (SEM), density and Vickers hardness measurements. The SEM results showed that the grain size of the sintered MgO increased from 200 nm to $1.9{\mu}m$ as the sintering temperature increased. The density results showed that the sintered MgO achieved a more than 95% of the theoretical density in overall sintering temperature range. Based on Vickers hardness test, we confirmed that hardness increased as temperature increased. Our results implied that we might obtain the dense sintered MgO samples with an extremely short time and low temperature HPHT process compared to conventional electrical furnace sintering process.

• Journal of Powder Materials
• /
• v.27 no.2
• /
• pp.146-153
• /
• 2020

The co-doping effect of aliovalent metal ions such as Mg²⁺, Ca²⁺, Sr²⁺, Ba²⁺, and Zn²⁺ on the photoluminescence of the Y₂O₃:Eu³⁺ red phosphor, prepared by spray pyrolysis, is analyzed. Mg²⁺ metal doping is found to be helpful for enhancing the luminescence of Y₂O₃:Eu³⁺. When comparing the luminescence intensity at the optimum doping level of each Mg²⁺ ion, the emission enhancement shows the order of Zn²⁺ ≈ Ba²⁺ > Ca²⁺ > Sr³⁺ > Mg²⁺. The highest emission occurs when doping approximately 1.3% Zn²⁺, which is approximately 127% of the luminescence intensity of pure Y₂O₃:Eu³⁺. The highest emission was about 127% of the luminescence intensity of pure Y₂O₃:Eu³⁺ when doping about 1.3% Zn²⁺. It is determined that the reason (Y, M)₂O₃:Eu³⁺ has improved luminescence compared to that of Y₂O₃:Eu³⁺ is because the crystallinity of the matrix is improved and the non-luminous defects are reduced, even though local lattice strain is formed by the doping of aliovalent metal. Further improvement of the luminescence is achieved while reducing the particle size by using Li₂CO₃ as a flux with organic additives.

• Korean Journal of Materials Research
• /
• v.29 no.2
• /
• pp.129-135
• /
• 2019

A powder mixture of 70 wt% $Al_2O_3$ and 30 wt% hydroxyapatite (HA) is sintered at $1300^{\circ}C$ or $1350^{\circ}C$ for 2 h at normal pressure. An $MgF_2$-added composition to make HA into fluorapatite (FA) is also prepared for comparison. The samples without $MgF_2$ show ${\alpha}$ & ${\beta}$-tricalcium phosphates (TCPs) and $Al_2O_3$ phases with no HA at either of the sintering temperatures. In the case of $1,350^{\circ}C$, a $CaAl_4O_7$ phase is also found. Densification values are 69 and 78 %, and strengths are 156 and 104 MPa for 1,300 and $1,350^{\circ}C$, respectively. Because the decomposition of HA produces a $H_2O$ vapor, fewer large pores of $5-6{\mu}m$ form at $1,300^{\circ}C$. The $MgF_2$-added samples show FA and $Al_2O_3$ phases with no TCP. Densification values are 79 and 87 %, and strengths are 104 and 143 MPa for 1,300 and $1,350^{\circ}C$, respectively. No large pores are observed, and the grain size of FA ($1-2{\mu}m$) is bigger than that of TCP ($0.7{\mu}m{\geq}$) in the samples without $MgF_2$. The resulting $TCP/Al_2O_3$ and $FA/Al_2O_3$ composites fabricated in situ exhibit strengths 6-10 times higher than monolithic TCP and HA.

• Resources Recycling
• /
• v.28 no.5
• /
• pp.74-79
• /
• 2019

The effects of equivalent of iron powder, particle size, agitation speed on the removal efficiency of copper ion were investigated by adding iron powder as cementation agents to simulated mine drainage solution with 117.15 mg/L Cu ion. The 50 % of Cu was removed at 90 min with 2 equivalent of iron powder while more than 99 % of Cu was removed at 60 min with 16 equivalent at 200 rpm and $20^{\circ}C$. The removal efficiencies of Cu ion were not different using 2 equivalent of $48{\mu}m$ and $150{\mu}m$ iron powder, and the removal efficiency increased rapidly with increasing the agitation speed to more than 400 rpm. This lower removal efficiency resulted from agglomeration of iron powder observed by SEM, which could reduce the effective specific surface area. More than 99 % of copper ion was removed using 2 equivalent of $48{\mu}m$ iron powder at 60 min, 600 rpm and $20^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.8
• /
• pp.831-840
• /
• 1997

Core/shell structured composite metal oxides of Fe2O3/MgO were prepared by thermal decomposition of Fe(acac)3 adsorbed on the surface of MgO cores. The morphology of the composites conformed to that of the MgO used as the cores. Broad powder X-ray diffraction peaks shifted toward larger d, large BET surface area (∼350 m2/g), and the size of crystalline domains in nano range (4 nm), all corroborate to the nanocrystallinity of the Fe2O3/MgO composite which was prepared by using nanocrystalline MgO as the core. By use of microcrystalline MgO as the core, microcrystalline Fe2O3/MgO composite was prepared, and it had small BET surface area of less than 35 m2/g. AFM measurements on nanocrystalline Fe2O3/MgO showed a collection of spherical aggregates (∼80 nm dia) with a very rough surface. On the contrary, microcrystalline Fe2O3/MgO was a collection of plate-like flat crystallites with a smooth surface. The nitrogen adsorption-desorption behavior indicated that microcrystalline Fe2O3/MgO was nonporous, whereas nanocrystalline Fe2O3/MgO was mesoporous. Bimodal distribution of the pore size became unimodal as the layer of Fe2O3 was applied to nanocrystalline MgO. The macropores in a wide distribution which the nanocrystalline MgO had were absent in the nanocrystalline Fe2O3/MgO. The decomposition of CCl4 was largily enhanced by the overlayer of Fe2O3 on nanocrystalline MgO making the reaction between nanocrystalline Fe2O3/MgO and CCl4 be nearly stoichiometric. The reaction products were environmentally benign MgCl2 and CO2. Such an enhancement was not attainable with the microcrystalline samples. Even for the nanocrystalline MgO, the enhancement was not attained, if not with the Fe2O3 layer. Without the layer of Fe2O3, it was observed that the nanocrystalline domain of the MgO transformed into microcrystalline one as the decomposition of CCl4 proceeded on its surface. It appeared that the layer of Fe2O3 on the particles of nanocrystalline Fe2O3/MgO blocked the transformation of the nanocrystalline domain into microcrystalline one. Therefore, in order to attain stoichiometric reaction between CCl4 and Fe2O3/MgO core/shell structured composite metal oxide, the morphology of the core MgO has to be nanocrystalline, and also the nanocrystalline domains has to be sustained until the core was exhausted into MgCl2.

• Journal of Microbiology and Biotechnology
• /
• v.22 no.8
• /
• pp.1155-1160
• /
• 2012

Sulfur-utilizing autotrophic denitrification relies on an inorganic carbon source to reduce the nitrate by producing sulfuric acid as an end product and can be used for the treatment of wastewaters containing high levels of nitrates. In this study, sulfur-denitrifying bacteria were used in anoxic batch tests with sulfur as the electron donor and nitrate as the electron acceptor. Various medium components were tested under different conditions. Sulfur denitrification can drop the medium pH by producing acid, thus stopping the process half way. To control this mechanism, a 2:1 ratio of sulfur to oyster shell powder was used. Oyster shell powder addition to a sulfur-denitrifying reactor completely removed the nitrate. Using 50, 100, and 200 g of sulfur particles, reaction rate constants of 5.33, 6.29, and $7.96mg^{1/2}/l^{1/2}{\cdot}h$ were obtained, respectively; and using 200 g of sulfur particles showed the highest nitrate removal rates. For different sulfur particle sizes ranging from small (0.85-2.0 mm), medium (2.0-4.0 mm), and large (4.0-4.75 mm), reaction rate constants of 31.56, 10.88, and $6.23mg^{1/2}/l^{1/2}{\cdot}h$ were calculated. The fastest nitrate removal rate was observed for the smallest particle size. Addition of chemical oxygen demand (COD), methanol as the external carbon source, with the autotrophic denitrification in sufficiently alkaline conditions, created a balance between heterotrophic denitrification (which raises the pH) and sulfur-utilizing autotrophic denitrification, which lowers the pH.

• Journal of the Korean Ceramic Society
• /
• v.54 no.1
• /
• pp.43-48
• /
• 2017

In this study, we investigate the effect of additive size on the densification and thermal conductivity of AlN ceramics with $MgO-CaO-Al_2O_3-SiO_2$ (MCAS) additives. Micro-sized MCAS powder prepared via melting and nano-sized MCAS powder synthesized via the polymeric complex method are used as sintering additives. We analyze the densification behavior of AlN added with 5 wt.% of MCAS by dilatometry as well as by isothermal sintering in the temperature range of $1300{\sim}1700^{\circ}C$. AlN exhibits higher sinterability with nano-MCAS than with micro-MCAS, and both specimens approach their maximum densities when sintered at $1600^{\circ}C$ for 4 h. The thermal conductivities of AlN with 5 wt% of nano- and micro-MCAS additives sintered at $1600^{\circ}C$ are 82.6 and 32.0 W/mK, respectively. We find that nano-MCAS is more effective in sintering of AlN ceramics at lower temperatures, and thus for enhancing their thermal conductivities.