• Korean Journal of Adult Nursing
• /
• v.14 no.4
• /
• pp.573-580
• /
• 2002

Purpose: The purpose of this study was to investigate the effects of a cardiac rehabilitation program for patients with myocardial infarction. Method: The subjects were 45 myocardial infarction patients(22 for experimental group and 23 for the control group). Data were collected through questionnaire survey, blood test, and the treadmill test, between October 1, 1999 and December 31, 2000. As for data analyses, paired and unpaired t-test and $\chi^2$ test were adopted using the SAS program. Result: 1. The post-test revealed that increase in compliance score of health behavior was significantly higher in the experimental group than in the control group. 2. The increase in HDL cholesterol was significantly higher in the experimental group than in the control group, in the post-test. 3. The experimental group showed significantly higher duration of exercise time and maximal METs than the control group after the program. Conclusion: The above findings indicate that a cardiac rehabilitation program was effective in increasing compliance of health behaviors, serum HDL cholesterol level, duration of exercise time, and maximal METs in patients with myocardial infarction. Accordingly, we can adopt the individualized cardiac rehabilitation programs as a nursing intervention.

• Journal of Ocean Engineering and Technology
• /
• v.7 no.2
• /
• pp.57-67
• /
• 1993

The fracture behavior of plain woven glass/epoxy composite plates with a crack is investigated under static tensile loading. It is shown in this paper that the characteristic length associated with the point stress criterion depends on the crack length. To predict the not ched tensile strength, the point stress criterion proposed by Whitney and Nuismer are modified. An excellent agreement is found between the experimental results and the analytical prediction of the modified point stress criterion. The condition of unstable crack growth in the presence of a per-existing flaw(machined notch) is examined by means of the maximum stress intensity factor $K_max$ using maximumload P$_max$. The values of $K_max$ evaluated from energy release rate G$_max$(the compliance me thod) indicate a wide difference. Therefore in regard to anisotropy and heterogeneity of the composite materials studied, the modified shape correction factor f(a/W) is obtained. $K_max$evaluated by the compliance method a little or insignificantly depends on the initial crack length a, the specimen thickness B, the crack angle .theta. and the specimen geometry.

• Nuclear Engineering and Technology
• /
• v.19 no.1
• /
• pp.1-9
• /
• 1987

The fracture toughness of SA 533 Grade B Class 1 steel has been studied with the Charpy impact test specimens in a range of temperature between -4$0^{\circ}C$ and 288$^{\circ}C$. The dynamic fracture toughness is measured by the instrumented precracked Charpy impact test while the static fracture toughness is by the 3-point bend test based on the unloading compliance method. The results are compared with the data obtained from the large specimens. It is known through the studies that temperature dependence of the appropriate (a low bound) value of the fracture toughness can be estimated by taking the static fracture toughness above the transition temperature and the dynamic fracture toughness below the temperature and it is also shown that the tests are satisfied with the requirements of ASTM E 813 when the side-groove is more than 14%.

• Journal of Biomedical Engineering Research
• /
• v.19 no.3
• /
• pp.313-320
• /
• 1998

Tri-phasic pulsatile flow is the general flow pattern of human circulary system. In emulating the various situation of cardiovascular system, it is essential to make tri-phasic source flow. To emulate tri-phasic pulsatile flow, we used electro-hydronic style LVAD(Left Ventricular Assist Device) with glass phantom and rubber tube. We have selected control parameters and examined the changing effect of each parameter by using Doppler ultrasound. In this experiment, it was shown that the distal compliance and the break time were the major factors to form tri-phasic flow. The results make it possible to emulate and explain the various situation of human vascular system. In this point, this results will be an useful method in the clinic application.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.11 s.170
• /
• pp.1952-1959
• /
• 1999

The work factor approach, so-called single specimen technique could be used to determine energy release rate from a single test record for unidirectional CLS specimen. In the present study, the work factor approach was extended to determine the mixed-mode fracture toughness of multi-directional graphite/epoxy laminated composites. Multi-directional CLS specimens were used for fracture tests. The stacking sequences used for the lap and the strap were $[90_2/0_2]_s/[0_4/90_4]_s$ and $[0/\pm45/0]_s/[0_2/\pm45_2/0_2]_2$, respectively. For both cases, the fracture toughness determined from the work factor approach was compared with that determined from the compliance method. It was found that both methods produced fracture toughness within a maximum 15% difference for each stacking sequence. The fractography analysis also showed that the fiber bridging occurred for$[0/\pm45/0]_s/[0_2/\pm45_2/0_2]_2$ case while it did not occur for $[90_2/0_2]_s/[0_4/90_4]_s$ case.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.4
• /
• pp.434-440
• /
• 1983

For the determination of stress intensity factors, three methods have been used conventionally; the photoelastic method, the compliance method and the electrical resistance method. These methods, however, have common short coming upon experimental performance; the difficulty of cutting out sharp crack tips and arbitray crack forms similar to the practical one on the specimen. to eliminate this flaw, one of the author previously presented new methods, that is, for the determination of $K_{III}$ mode, the membrane analogy was applied and the slab analogy was used for the determination of $K_{I}$ and $K_{II}$ . The validity of this method was proved through the performance of a series of experiments of which theoretical solution are known.n.n.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.131-134
• /
• 2002

Braided carbon fiber reinforced Al matrix composites were developed and characterized. Braided carbon fiber preforms with braiding angles of $30^{\circ}$, $45^{\circ}$ and $60^{\circ}$ were manufactured by using a braiding machine. The manufactured braided carbon fibers were used as reinforcement to fabricate Al matrix composites by employing a pressure infiltration casting method. In the processing of pressure infiltration casting, important processing parameters such as melting temperature, preheating temperature of preform and applied pressure were optimized. Prediction of elastic constants on composites was performed by using the volume averaging method, which utilizes the coordinate transformation and the averaging of stiffeness and compliance constants based upon the volume of each reinforcement and matrix material. The elastic moduli of composites were evaluated by using Resonant Ultrasound Spectroscopy(RUS) method and compared with the elastic moduli obtained from static tensile test method.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.453-458
• /
• 2002

The feasibility study on supporting a turbocharger rotor on air foil bearing is investigated. Based on finite difference method and Newton-Raphson method, the static equilibrium position of a turbocharger rotor is predicted. And using finite difference method and perturbation method, dynamic characteristics of air foil bearings are calculated. Rotordynamic analysis is performed by finite element method, with collaboration of calculated stiffness and damping of foil bearing. The effect of compliance and clearance of bump foil bearing on the oil-free turbocharger is investigated in terms of rotordynamics. And the critical speeds, eccentricity ratio, vibration amplitude, and stability are considered. It is demonstrated that foil bearings offer a rlausible replacement for oil-lubricated bearings in turbocharger.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.11
• /
• pp.114-125
• /
• 1997

This paper presents a method that automatically recognizes dimension sets from the mechanical drawings, and that classifies 6 types dimension sets according to functional purpose. In the proposed method, the object and closed-loop symbols are separated from the character-free drawings. Then object lines and interpretation lines are vectorized. And, after recognizing dimension sets(consistings of arrowhead, shape line, tail lines, extension lines, text-string, and feature control frame), we classify recognized dimension sets as horizontal, vertical, angular, diametral, radial, and leader dimension sets. Finally the proposed method converts classified dimension sets into AutoCAD data by using AutoLisp language. By using the methods of geometric modeling, the proposed method readily recognized and classifies dimension sets from complex drawings. Experimetnal results are presented, which are obtained by applying the proposed method to drawings drawn in compliance with the KS drafting standard.

• 전자공학회논문지 IE
• /
• v.46 no.3
• /
• pp.48-54
• /
• 2009

In this paper, a test method of HDMI connectors is developed using a test zig. This method is used to test the characteristic for a digital signal connector, and is applied the compliance test specification. The test results of connectors for the two manufactory are implemented by the new proposed method. Finally, it is suggested to the new test method of HDMI connector in this paper, and is applied to the simple test method of connector in manufactory.