• 자원리싸이클링
• /
• 제10권1호
• /
• pp.49-55
• /
• 2001

The strategy of recovering metals from scrap is in general much different from primary sources. One of the main differences between the treatment of scrap and that of primary sources lies with the fact that metals are frequently associated with other met-als to form alloys in scrap, while metals occur in primary sources as oxides or sulfides. In this paper, factors affecting the dis-solution behavior of metals from various alloy systems have been reviewed and discussed. Specific examples have been drawn from Au/Ag, Au/cu and Ag/cu systems. Results of the dissolution behavior of various metals from these alloys have been reviewed and compared to the dissolution behavior of single metal systems in various lixiviants such as acids, cyanide and ammonia. It has been observed that the presence of other metals in alloys would significantly affect the dissolution rate of the metal in question. The leaching behavior of metals from homogeneous alloys relies on the chemical interaction between atoms in the lattice of the alloys, while that from heterogeneous alloys is affected by galvanic interaction established in the solution The manner in which the dissolution of a certain metal is influenced by surrounding metals has been discussed in terms of pas-sive and noble nature of the metal in relation to the neighboring metals. The role of the standard electrochemical Potential of these metals on the selective dissolution for a given lixiviant has also been discussed.

• Metals and materials international
• /
• 제24권6호
• /
• pp.1213-1220
• /
• 2018

The effects of Cr and Fe addition on the mechanical properties of Ti-6Al-4V alloys prepared by direct energy deposition were investigated. As the Cr and Fe concentrations were increased from 0 to 2 mass%, the tensile strength increased because of the fine-grained equiaxed prior ${\beta}$ phase and martensite. An excellent combination of strength and ductility was obtained in these alloys. When the Cr and Fe concentrations were increased to 4 mass%, extremely fine-grained martensitic structures with poor ductility were obtained. In addition, Fe-added Ti-6Al-4V resulted in a partially melted Ti-6Al-4V powder because of the large difference between the melting temperatures of the Fe eutectic phase (Ti-33Fe) and the Ti-6Al-4V powder, which induced the formation of a thick liquid layer surrounding Ti-6Al-4V. The ductility of Fe-added Ti-6Al-4V was thus poorer than that of Cr-added Ti-6Al-4V.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.547-548
• /
• 2006

The main object of this research was to examine the effect of sintering conditions on the microstructure of tungsten heavy alloys and how the resulting modification of the microstructure can be used to optimize their mechanical properties. Alloys composed of 88%, 93% and 95% wt. of tungsten and the balance is Ni: Fe in the ratio of 7:3 were sintered at different temperatures for different sintering holding times in hydrogen atmosphere. It was shown that the mechanical properties of the alloys, and especially their ductility, are harmed when tungsten grains are contiguous.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.491-495
• /
• 1995

The crystallization behaviors and magnetic properties for $Fe_{81-x}Al_{4}B_{10}Zr_{5}Cu_{x}$ (x=0, 1, 2 at%) alloys is investigated. By the addition of 1~2 Cu, the temperature range, where a single bcc phase exists, expands largely over 200 K and the grain size of bcc phase represents to less than 10 nm. For the optimally annealed Cu-added alloys, the high $\mu_{e}$ (1 kHz) above 20000 combined with the high $B_{10}$ of about 1.4 T is obtained in nanocrystalline state. The low core loss of 95.8 W/kg at 0.1 T and 100 kHz is confirmed for the nanocrystalline $Fe_{80}Al_{4}B_{10}Zr_{5}Cu_{1}$ alloy.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.487-490
• /
• 1995

With the object of developing a new magnetic core materials for high frequency use, the crystallization behaviors and the soft magnetic properties of amorphous $F_{86-x}Al_{4}B_{10}Zr_{x}\;(5{\leq}x{\leq}10\;at%)$ alloys subjected to annealing treatment at wide temperature range were investigated. For optimally annealed $Fe_{86-x}Al_{4}B_{10}Zr_{x}$ alloys in amorphous state, rather good soft magnetic properties of ${\mu}_{e}=17000~25000,\;H_{c}=20~30$ mOe and $B_{10}{\geq}0.6$ T are obtained. However, as the alloys crystallize, the soft magnetic properties are largely dergely deteriorated, which is attributed principally to the narrow temperature gap between $T_{x1}$ and $T_{x2}$, which allows the nearly co-precipitation of bcc phase and Fe-B compounds in incipient crystallization stage.

• Journal of Magnetics
• /
• 제21권1호
• /
• pp.12-19
• /
• 2016

The <100> oriented $Fe_{83}Ga_{17}$ alloys with various contents of NbC or B were prepared by directionally solidification method at the growth rate of $720mm{\cdot}h^{-1}$. With a small amount of precipitates, the columnar grains grew with cellular mode during directional solidification process, while like-dendrite mode of grains growth was observed in the alloys with higher contents of 0.5 at% due to the dragging effect of precipitates on the boundaries. The NbC precipitates disperse both inside grains and along the boundaries of $Fe_{83}Ga_{17}$ alloys with NbC addition, and the Fe2B secondary phase particles preferentially distribute along the grain boundaries in B-doped alloys. Precipitates could affect grain growth and improved the <100> orientation during directional solidification process. Small amount of precipitate element addition slightly increased the magnetostrictive strain, and a high value of 335 ppm under pre-stress of 15 MPa was achieved in the alloys with 0.1 at% NbC. Despite the fact that the effect on magnetic induction density of small amount of precipitates could be negligible, the coercivity markedly increased with addition of precipitate element for $Fe_{83}Ga_{17}$ alloy due to the retarded domain motion resulted by precipitates.

• 한국수소및신에너지학회논문집
• /
• 제15권4호
• /
• pp.266-273
• /
• 2004

The objective of this study is an understanding of stress corrosion cracking of metals that is recognized to mostly limit the lifetime of the structural materials by comparing the features of delayed hydride cracking of zirconium alloys with those of stress corrosion cracking (SCC) of Ni-based alloys and hydrogen cracking of stainless steels. To this end, we investigated a dependence of delayed hydride cracking (DHC) velocity on the applied stress intensity factor and yield strength, and correlated a temperature dependence of the striation spacing and the DHC velocity. We reviewed a similarity of the features between the DHC of zirconium alloys, the SCC of Ni-based alloys and turbine rotor steels, and the hydrogen cracking of stainless steels and discussed the SCC phenomenon in metals with our DHC mode.

• Journal of Welding and Joining
• /
• 제17권4호
• /
• pp.26-31
• /
• 1999

An attempt was made in this study to investigate the brazing characteristics of Zr-Be binary amorphous alloys for the development of a new brazing filler metal for joining Zircaloy-4 nuclear fuel cladding tubes. This study was also aimed at the feasibility study of rapidly solidified amorphous alloys to substitute the conventional physical vapor-deposited(PVD) metallic beryllium. The $Zr_{1-x}Be_{x}$($0.3\leq$x$\leq0.5$) binary amorphous alloys were produced in the ribbon form by the melt-spinning method. It was confirmed by x-ray diffraction that the ribbons were amorphous. The amorphous. the amorphous alloys were used to join bearing pads on Zircaloy-4 nuclear fuel cladding tubes. Using Zr-Be amorphous alloys as filler metals, it was found that the reduction in the tube wall thickness caused by erosion was prevented. Especially, in the case of using $Zr_{0.65}Be_{0.35}$ and $Zr_{0.7}Be_{0.3}$ amorphousalloys, the smooth and spherical primary $\alpha$-Zr particles appeared in the brazed layer, which was the most desirable microstructure from the corrosion-resistance standpoint.

• 대한금속재료학회지
• /
• 제47권11호
• /
• pp.759-772
• /
• 2009

Amorphous alloys, in addition to being promising materials for a variety of practical applications, provide an excellent test bed for evaluating our understanding of the underlying physics on deformation in amorphous solids. Like many amorphous materials, amorphous alloys can exhibit either homogeneous or inhomogeneous deformation depending on the stress level. The mode of deformation has a strong influence on whether the material behavior is classified as ductile or brittle. It was observed that the characteristics of these deformations are largely dependent on the atomic-scale structures of the alloys and determine the amount of the plastic deformation prior to failure. In this study, the structural features that control the homogeneous deformation of amorphous alloys are outlined on the basis on experiments and molecular dynamics simulations.

• Applied Microscopy
• /
• 제21권2호
• /
• pp.57-66
• /
• 1991

The main purpose of this paper was to investigate the change of rapidly solidified microstructures and dispersoid behavior according to heat-treatment in the Al-Fe-V-Si-(Mn) alloys. It was found that (111) preferred orientation identified by X-ray diffraction and fine subgrain/large grain were observed in the rapidly solidified Al-Fe-V-Si-(Mn) alloys. Cell boundary of the zone A was composed of the microcrystalline, whereas that of the zone B was amorphous. Decomposition of the Al-Fe-V-Si-(Mn) alloys occurred at about $300^{\circ}C$. These alloys exhibited excellent thermal stability at the elevated temperature. Microstructure of the zone B was more stable than that of the zone A. The spherical dispersoid and 5-fold symmetry phase was also more thermally stable than the amorphous structure of cell boundary.