• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.7
• /
• pp.712-720
• /
• 2003

In this paper, a multi-layered metallic disk array structure(MDAS) excited by cross-dipole elements was proposed for efficiently shaping of flat-topped element patterns(FTEP) with circular polarization. The MDAS excited by cross-dipole elements has advantages to decrease in volume and weight of an overall array antenna and so, it is appropriate for the FTEP applications of a ralativlely low frequency band. In order to verify the effectness of this structure, the MDAS breadboard operated at X-band(7.9 ∼ 8.4 GHz) was fabricated, and its design parameters were experimentally optimized on the basis of the previous design experience. The experimental results were shown that the MDAS could shape good FTEPs of ${\pm}$20$^{\circ}$beam width at least within a 6.1 % frequency band.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.218-223
• /
• 2000

The shot peening is largely used for a surface treatment in which small spherical parts called shots are blasted on a surface of a metallic components with velocities up to 100m/s. This treatment leads to an improvement of fatigue behavior due to the developed compressive residual stresses, and so it has gained widespread acceptance in the automobile and aerospace industries. The residual stress profile on surface layer depends on the parameters of shot peening, which are, shot velocity, shot diameter, coverage, impact angle, material properties etc. and the method to confirm this profile is only measurement by X-ray diffractometer. Despite its importance to automobile and aerospace industries, little attention has been devoted to the accurate modelling of the process. In this paper, the simulation technique is applied to predict the magnitude and distribution of the residual stress and plastic deformation caused by shot peening with the help of the finite element analysis.

• Tribology and Lubricants
• /
• v.36 no.6
• /
• pp.378-384
• /
• 2020

The friction surfaces of mechanical parts are heat-treated or coated with hard materials to minimize wear. Increasing the hardness is a very useful way to reduce abrasive wear. The general Brinell hardness test, which is widely used for metallic materials, is not suitable because it hardly shows any change in hardness when coated with thin films. In this study, we propose a basis for the application of the new Brinell hardness test method to the coated friction surface. An indentation analysis of the rigid sphere and elastic-perfectly plastic materials is performed using a commercial finite element analysis software. The results indicate that their loadto-diameter ratio is the same; the Brinell hardness test method can be applied even when the indenter diameter is on the micrometer scale. In the case of hard coating, it is difficult to calculate Brinell hardness using the diameter of the indentation, but the study revealed, for the first time, that it can be calculated using the depth of the indentation regardless of coating. The change in hardness owing to thin film coating over a wide load range implies that the hardness evaluation method is appropriate. Additional studies on various properties related to the substrate and coating material are required to apply the proposed method.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.5
• /
• pp.47-60
• /
• 2007

In this paper, we investigate the natural frequencies and buckling loads of functionally graded material (FGM) plates and shells, using a quasi-conforming shell element that accounts for the transverse shear strains and rotary inertia. The eigenvalue of the FGM plates and shells are calculated by varying the volume fraction of the ceramic and metallic constituents using a sigmoid function, but their Poisson's ratios of the FGM plates and shells are assumed to be constant. The expressions of the membrane, bending and shear stiffness of FGM shell element are more complicated combination of material properties than a homogeneous element. In order to validate the finite element numerical solutions, the Navier's solutions of rectangular plates based on the first-order shear deformation theory are presented. The present numerical solutions of composite and sigmoid FGM (S-FGM) plates are proved by the Navier's solutionsand various examples of composite and FGM structures are presented. The present results are in good agreement with the Navier's theoretical solutions.

• Composites Research
• /
• v.29 no.4
• /
• pp.203-208
• /
• 2016

Metal and polymer sandwich composites, which are made of sheet metal sheath and polymer or fiber reinforced plastic core, have been reconsidered as an alternative to sheet metal due to their lightness and multifunctional properties such as damping and sound-proof properties. For the successful applications of these composites, the delamination prediction based on the adhesion strength is important element. In this study, the numerical simulation of the delamination behavior of polymeric adhesive tapes with metallic surfaces was performed using cohesive zone elements and finite element software. The traction-separation law of the cohesive zone element was defined using the fracture energy derived from peel mechanics and experimental results from peel test and implemented in finite element software. The peel test of the polymeric adhesive film against steel surface was simulated and compared with experiments, demonstrating reasonable agreement between simulation and experiment.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.10
• /
• pp.883-891
• /
• 2016

In this paper, we propose an asymmetric dipole antenna utilizing the metal case as a ground radiator for a pen-type wireless presenter which operates in the ISM frequency band(2.4~2.48 GHz). A normal mode helix mounted on the top end of the long metallic cylinder case which acts as the ground plane takes the form of the asymmetric dipole structure in the proposed antenna. The metallic cylinder case which performs as a radiating element increases the inherent narrow bandwidth and low gain of the helix. The effects of the hand contacts with the metal case on the antenna performance are measured and analyzed with a specially designed human phantom. Experimental results show that the -10 dB return loss bandwidth of the proposed antenna in free space(no hand contact) is 200 MHz that ranges from 2.3 to 2.5 GHz and the maximum gain is measured to be 5 dBi. Under the normal operating condition where the metal case is contacted with a human hand, the bandwidth is 480 MHz from 2.24 to 2.72 GHz. The maximum gain is 2 dBi, lowered by 3 dB due to the hand contact.

• Structural Engineering and Mechanics
• /
• v.58 no.3
• /
• pp.515-532
• /
• 2016

The elastoplastic response of functionally graded material (FGM) beams resting on a nonlinear elastic foundation to an eccentric axial load is investigated by using the finite element method. The FGM is assumed to be formed from ceramic and metal phases with their volume fraction vary in the thickness direction by a power-law function. A bilinear elastoplastic behavior is assumed for the metallic phase, and the effective elastoplastic properties of the FGM are evaluated by Tamura-Tomota-Ozawa (TTO) model. Based on the classical beam theory, a nonlinear finite beam element taking the shift in the neutral axis position into account is formulated and employed in the investigation. An incremental-iterative procedure in combination with the arc-length control method is employed in computing the equilibrium paths of the beams. The validation of the formulated element is confirmed by comparing the equilibrium paths obtained by using the present element and the one available in the literature. The numerical results show that the elastoplastic post-buckling of the FGM beams is unstable, and the post-buckling strength is higher for the beams associated with a higher ceramic content. Different from homogeneous beams, yielding in the FGM beam occurs in the layer near the ceramic layer before in the layer near metal surface. A parametric study is carried out to highlight the effect of the material distribution, foundation support and eccentric ratio on the elastoplastic response of the beams.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.4
• /
• pp.392-402
• /
• 2020

We investigated the concentrations of acid volatile sulfide (AVS), ignition loss (IL), total organic carbon (TOC), total nitrogen (TN), and metallic elements (As, Cd, Cr, Cu, Fe, Hg, Mn, Pb, and Zn), in August 2015, to determine the spatial distribution and pollution status of organic matter and metals in the surface sediment of Jinju Bay, a spraying shellfish farming area, Korea. The concentrations of organic matter and metallic elements were significantly higher in the southern part of the bay than in the mouth and center of the bay. The C/N ratio (5.7~8.0) in the sediment represents the dominance of organic matter of oceanic origin in the surface sediment of the study area. The concentrations of AVS, TOC, and metals (As, Cd, Cr, Cu, Hg, Pb, and Zn) were much lower than the values of the sediment quality guidelines applied in Korea. Based on the results of the pollution load index (PLI) and ecological risk index (ERI), the metal concentrations in the surface sediment of Jinju Bay have a weakly negative ecological effect on benthic organisms although the sediments with high metal pollution status are distributed in the southern parts of the bay, with high dense shellfish farming areas. Thus, the surface sediments in Jinju Bay are not polluted with organic matter and are slightly polluted with metallic elements.

• Journal of the Korean earth science society
• /
• v.31 no.3
• /
• pp.234-245
• /
• 2010

Twenty-four hour integrated $PM_{10}$ and $PM_{2.5}$ samples were measured during springtime (March, April, and May) in Busan for three years from 2006 to 2008, and mass concentrations and metallic elements of measurement were analyzed to investigate temporal, spatial, chemical characteristics of the mass concentration and metallic elements in association with meteorological conditions including Asian Dust (AD) vs. non Asian Dust (NAD) seasons, and other air mass transport patterns. The result showed that $PM_{10}$, $PM_{2.5}$ and $PM_{10-2.5}$ concentrations were on average of $126.2{\pm}89.8$, $85.5{\pm}41.6$, and $40.7{\pm}54.9{\mu}g/m^3$, respectively, and the $PM_{2.5}/PM_{10}$ and $PM_{10-2.5}/PM_{2.5}$ ratios were 0.70 and 0.48, respectively. The highest concentrations of PM were observed when air parcels were originated from both northwest sector covering Beijing and west sector including Shanghai areas.

• Journal of the Korean Society of Safety
• /
• v.31 no.6
• /
• pp.1-5
• /
• 2016

A bicycle is one of the most popular sporting goods in view of a sport activity and a human health. Metallic materials such as steel, aluminum, etc. were mainly used to the bicycle fork in the past. Nowadays, the carbon fiber reinforced composite materials are widely used to the manufacturing of a bicycle fork to reduce the weight and to increase the efficiency. Safety is a most important design parameter of a bicycle fork even if the weight and cost reduction are important. Bicycle failure may happen at the critical spot of a bicycle fork and cause the accident. In this paper, the composite bicycle fork will be analyzed to secure the safety and detect a critical spot by using the finite element method with Tsai-Wu failure criterion. The stress data were obtained for the laminated composites with various number of plies and fiber orientation under the bending load. Thus, design concept of a bicycle fork was proposed to secure the safety of a bicycle. The finite element analysis results show that the connection area between a steer tube and a fork blade is critical spot, and 75 or more layers of 0 degree are needed to secure the safety of a bicycle fork.