• 산업기술연구
• /
• 제31권A호
• /
• pp.45-51
• /
• 2011

A study has been made on defects which are formed in manufacturing processes of engine bearing and also on fatigue crack growth behavior in each step of bearing metal manufacturing. After the first step (sinter brass powder on steel plate ; Series A) many voids are made on brass surface and its size is decreased at the second step (rolling process of sintered plate ; Series B). After the third step (re-sintering step of brass powder and rolling ; Series C) the number of voids is decreased and its type shows line. The time of fatigue crack initiation and the growth rate of fatigue crack are in order of Series A, Series B, Series C. These reasons are that void fosters the crack initiation and growth, and residual stress made by rolling process affects on the crack growth rate in Series B, C. In forming and machining processes by use of final bearing metal, crack was observed at internal corner of flange and peeling off was observed at interface between steel and brass. Owing to the above crack and peeling off, it is considered that there is a possibility of fatigue fracture during the application time.

• 한국산학기술학회논문지
• /
• 제11권12호
• /
• pp.4715-4720
• /
• 2010

본 논문은 판재 성형을 위한 제관 라인의 판재 이송부에 장착되는 판재 누름키의 설계 개선에 관한 연구이다. 기존의 블록형 누름키가 판재의 종 방향 및 횡 방향 이송 과정에서 깊은 스크래치가 유발되는 것을 방지하기 위해 테이퍼진 롤러가 누름키 내부에 장착되어 가이드하도록 하는 테이퍼 롤러 누름키를 개발하였다. 이를 통해 판재의 종 방향 이송시 테이퍼 형상의 효과로 접촉부의 압력 스파이크를 저감시켜 판재의 스크래치 발생을 최소화하고 횡방향 이송시 미끄럼 접촉이 아닌 구름 접촉으로 유도하여 표면 스크래치를 원천적으로 방지할 수 있음을 스크래치 실험을 통해 그 효과를 확인하였다.

• 열처리공학회지
• /
• 제33권2호
• /
• pp.49-56
• /
• 2020

Magnesium alloy is a metal with high specific strength and light weight, and is attracting attention as a next generation metal for environmentally friendly automobiles and transportation equipment. However, magnesium alloys have a problem of degrading formability due to the basal texture developed during processing, and their application is limited. Although active researches on the control of textures have been conducted in order to minimize this problem, there is a lack of research on the formation of microstructures and textures according to elemental differences. In this study, AZ61 and AZ80 magnesium alloys were selected to investigate the effects of aluminum addition on the microstructure development of magnesium alloys. This research has proven that the increase of the rolling rate results in the decrease of the average grain size of the two alloys, the increase of the hardness, and the increase of the fraction of twins. As shown on this research below, the basal texture developed strongly as the rolling ratio increased. On the other hand, this research also has proven that the two alloys exhibited different texture strength and distribution tendencies, which could be due to the effects of aluminum addition on work hardening, grain size, and twin behavior.

• 소성∙가공
• /
• 제32권3호
• /
• pp.114-121
• /
• 2023

During rolling, rolling mill rolls endure wear when shaping metal billets into a desired form, such as bars, plates, and shapes. Such wear affects the lifespan of the rolls and product quality. Therefore, in addition to rigidity, wear performance is a key factor influencing the performance of rolling mill rolls. Conventional methods such as casting and forging have been used to manufacture rolling mill rolls. However, powder alloying methods are increasingly being adopted to enhance wear resistance. These powder manufacturing methods include atomization, canning to shape the powder, hot isostatic pressing to combine the powder alloy with conventional metals, and various wear performance tests on rolls prepared with powder alloys. In this study, numerical simulations and experimental tests were used to develop and elucidate the wear analysis mechanism of rolling mill rolls. The wear characteristics of the rolls under various rolling conditions were analyzed. In addition, experimental tests (wear and surface analysis tests) and wear theory (Archard wear model) were used to evaluate wear. These tests were performed on two different materials in various powder states to evaluate the different aspects of wear resistance. In particular, this study identifies the factors influencing the wear behavior of rolling mill rolls and proposes an analytical approach based on the actual production of products. The developed wear analysis mechanism can serve the future development of rolls with high wear resistance using new materials. Moreover, it can be applied in the mechanical and wear performance testing of new products.

• Journal of Mechanical Science and Technology
• /
• 제20권9호
• /
• pp.1410-1417
• /
• 2006

The metal processing system usually consists of various components such like motors, work rolls, backup rolls, idle rolls, sensors, etc. Even a simple fault in a single component in the system may cause a serious damage on the final product. It is therefore necessary to diagnose the faults of the components to detect and prevent system failure. Especially, the defects in a work roll are critical to the quality of strip. It is especially difficult to detect faults of a roll by using the existing frequency analysis method if the speed of the roll is changing. In this study, a new diagnosis method for roll eccentricity under the roll speed changes was developed. The new method was induced from analyzing the rolling mechanism by using rolling force models, radius-speed relationship, and measured rolling force, etc. Simulation results by using the field data show that the proposed method is very useful.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.384-388
• /
• 1997

Recently,direct rolling process has been drawing increasing interests because production cost be greatly reduced by eliminating subsequent hot rolling processes. Such a process has been characterized to prosuce thin steel strip (thickness 1~5mm) directly from molten metal and to skip over the conventional hot rolling processes. However, since there are several process parameters, which affect the quality of product,and their relationship between the parametersare very complex,it is therefore very difficult to realize the process design and the quality control. To overcome these difficulties quantitative relationship between the parameters are investigated through a numerical analysis. Form these results, it is found that solidification final point is the most important paramter which is critical to quality of the strip. Also,the multiple regression model is obtianed to determine their relationship from the solidification final point and roll separating force which can be easily estimated

• Journal of Mechanical Science and Technology
• /
• 제18권12호
• /
• pp.2174-2181
• /
• 2004

The metal processing system usually consists of various components such as motors, work rolls, backup rolls, idle rolls, sensors, etc. Even a simple fault in a single component in the system may cause a serious damage on the final product. It is, therefore, necessary to diagnose the faults of the components to detect and prevent a system failure. Especially, the defects in a work roll are critical to the quality of strip. In this study, a new 3-D diagnosis method was developed for roll shape defects in rolling processes. The new method was induced from analyzing the rolling mechanism by using a rolling force model, a tension model, the Hitchcock's equation, and measurement of the strip thickness, etc. Computer simulation shows that the proposed method is very useful in the diagnosis of the 3-D roll shape.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1991년도 춘계학술대회 논문집
• /
• pp.251-255
• /
• 1991

The primary objectives of the rolling process are to reduce the cross section of the incoming material while improving its properties and to obtain the desired section at the exit from the rolls. Many engineering metals, suchas aluminium alloys, copper alloys, and steels are often cast intoingots and are then further processed byhot rolling into blooms, slabs, and billets, which are subsequently rolled into other products such as plate, sheet, tube, rod, bar, and structural shapes. In shape rolling a round or square bar is rolled in several passes into various shapes. During eachpass, the bar elongates as well as spreads. Thus, a very complex three-dimensional metal flow takes place. In this paper TASKS results for the simulation of a 7 pass square-to-round shape rolling are presented. The results are verified by comparing it with experimental results from a previous study conducted at the Battelle Columbus Labs

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.133-137
• /
• 2002

This paper summarizes the results of a numerical study conducted to analyze the determination of optimum blank diameter on material flow and thread profile for Spindle Screw in external thread rolling. Initial blank diameter affect a quality of Spindle Screw in thread rolling process. Therefore, it is very important to determine the optimum blank diameter in thread rolling process. In order to determine the optimum blank diameter, this paper suggest the calculating method of initial blank diameter considering real shape of tooth. The finite element code DEFORM is applied to analyze the metal flow of tooth. then the analytical results are verified by experiment of thread rolling for Spindle Screw.

• 소성∙가공
• /
• 제19권4호
• /
• pp.248-252
• /
• 2010

In this paper, three-dimensional finite element analysis of thread rolling process of a 12 point flange head bolt is conducted using a rigid-plastic finite element method based metal forming simulator AFDEX 3D. A whole sequence of cold forming processes of a long shaft bolt composed of four forging stages and final thread rolling process is simulated to reveal the mechanism of thread formation. A mesh density control function is applied near the major plastic deformation region to achieve computational efficiency. It has been shown both numerically and experimentally that longitudinal lengthening or shortening is negligible in thread rolling.