• 한국정밀공학회지
• /
• 제21권8호
• /
• pp.34-42
• /
• 2004

A new polishing technique for three dimensional micro/meso-scale parts is suggested using a micro quill and a magnetic chain structure. The principle of this method is to polish the target surface with the collected magnetic brushes at a micro tool by the non-uniform magnetic field generated around the tool. In a typical magnetic abrasive finishing process magnetic particles and abrasive particles are unbonded each other. But, to finish the three dimensional small parts bonded magnetic abrasive have to be used. Bonded magnetic abrasives are made from direct bonding, and their polishing characteristics are also examined. Alumina, silicon carbide and diamond micro powders are used as abrasives. Base metal matrix is carbonyl iron powder. It is found that bonded magnetic abrasives are superior to unbonded one by experiment. finally, the polished surface roughness is evaluated by atomic force microscope.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.397-400
• /
• 2004

The direct extrusion with porthole die can produce condenser tube which has the competitive power in costs and qualities compared with the existing conform extrusion. In general, porthole die extrusion has a great advantage in the forming that produces the hollow sections difficult to produce by conventional extrusion with a mandrel on the stem. Especially, condenser tube manufactured by porthole die belongs to sophisticated part and demands tighter dimension tolerance and higher surface finish than any other part. In order to confirm the general of porthole die extrusion, we perform the 3D FE analysis of hot porthole extrusion in non-steady state by using DEFORM 3D and investigate a pattern of elastic deformation for porthole die through the stress analysis using ANSYS 5.5 during extrusion process.

• Journal of Welding and Joining
• /
• 제33권3호
• /
• pp.32-39
• /
• 2015

With the simplicity of process and high reliability in chip or package bonding, epoxy solder paste (ESP) has been recently considered as a competitive bonding material. The ESP material is composed of solder powder and epoxy formulation which can remove oxide layers on the surface of solder powder and pad finish metal. The bonding formed using ESP shows outstanding bonding strength and suppresses electrical short between adjacent pads or leads owing to the reinforced structure by cured epoxy after the bonding. ESP is also expected to suppress the formation and growth of whisker on the pads or leads. With the mentioned advantages, ESP is anticipated to become a spotlighted bonding material in the assembly of flexible electronics and electronic modules in automotive vehicles.

• 한국건설관리학회논문집
• /
• 제6권5호
• /
• pp.139-147
• /
• 2005

During a typical construction project, a contractor nay often find that the time originally available or normally expected to perform its work has been severely reduced. To finish the project by the completion date, the contractor is forced to find a way to speed up the progress of its work to compensate for the reduction in available time. The most frequent initial reaction of contractors to this situation is to increase on-site manpower by working longer time (overtime), adding more workers (overmanning), or implementing shift work (shift work) to increase the rate of progress. The goals of this study were to investigate how these three methods affect labor productivity and to quantify their impact on labor productivity by analyzing real project data collected from sheet metal contractors and mechanical contractors in the US.

• 한국정밀공학회지
• /
• 제19권3호
• /
• pp.80-87
• /
• 2002

Tungsten carbide microshaft is used as micro-punch, electrode of MEDM (micro-electro-discharge machining), and micro-tool because it has high hardness and high rigidity. In this study, the tungsten carbide microshaft was fabricated using electrochemical machining. Concentration of material removal at the sharp edge and metal corrosion layer affect the shape of the microshaft. Control of microshaft shape was possib1e through conditioning the machining voltage and electrolyte concentration. By applying periodic voltage, material removal rate increased and surface roughness improved. The fabricated microshaft in $H_2 SO_4$ electrolyte maintained sharper end edge and better surface finish than those fabricated by other electrolytes.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.28-33
• /
• 2004

At present, industry and researchers are looking for ways to reduce the use of lubricants because of ecological and economical reasons. Therefore, metal cutting is to move toward dry cutting or semi-dry cutting. This paper presents an investigation into MQL(Minimum Quantity Lubrication) machining with the objective of deriving the optimum cutting conditions for the turning process of SM45C. To reach these goals several finish turning experiments were carried out, varying cutting speed, feed rate and oil quantity, with MQL. The surface roughness results of tests were measured and the effects of cutting conditions were analyzed by the method of Analysis of Variance(ANOVA). From the experimental results and ANOVA, it is found that a better surface roughness can be obtained by decreasing oil quantity and feed rate.

• 한국정밀공학회지
• /
• 제18권10호
• /
• pp.208-213
• /
• 2001

High speed milling(HSM) is one of the emerging cutting process having tremendous potential not only in increased metal removal rates but also in improved surface finish, burr free edge, dimensional accuracy and a virtually stress free component after machining. The High efficiency and accuracy in machining of die/mold materials can be obtained in high speed machining, so it is necessary to analytic the mechanism of high speed cutting process : cutting force, acoustic emission signal.

• 한국정밀공학회지
• /
• 제17권7호
• /
• pp.90-97
• /
• 2000

This paper presents a methodology to analyze the cutting fluid effectiveness in mechanical and thermal terms simultaneously using finite element method and experimental work. Cutting fluid plays many roles in metal cutting process. Mechanically-thermally coupled effectiveness of cutting fluids affect to friction coefficient at tool-workpiece interface and cutting temperature and chip control, surface finish, tool wear and form accuracy. Through this study, it can be explained that the critical behavior of cutting fluids will be able to apply optimal environmentally conscious machining process.

• Journal of Computational Design and Engineering
• /
• 제2권3호
• /
• pp.137-147
• /
• 2015

In this study, a new methodology in predicting a system output has been investigated by applying a data mining technique and a hybrid type II fuzzy system in CNC turning operations. The purpose was to generate a supplemental control function under the dynamic machining environment, where unforeseeable changes may occur frequently. Two different types of membership functions were developed for the fuzzy logic systems and also by combining the two types, a hybrid system was generated. Genetic algorithm was used for fuzzy adaptation in the control system. Fuzzy rules are automatically modified in the process of genetic algorithm training. The computational results showed that the hybrid system with a genetic adaptation generated a far better accuracy. The hybrid fuzzy system with genetic algorithm training demonstrated more effective prediction capability and a strong potential for the implementation into existing control functions.

• 소성∙가공
• /
• 제11권8호
• /
• pp.710-715
• /
• 2002

This paper describes the numerical determination of optimum blank diameter for sound material flow and high precise thread profile of a spindle screw through external thread rolling using two-three roll dies. Initial blank diameter affects the dimensional accuracy and surface finish qualities of a spindle screw in thread rolling process, therefore it is very important to determine the optimum blank diameter in thread rolling process. In order to determine the optimum blank diameter, this paper suggests the calculation method of initial bland diameter considering the real shape of tooth. The finite element code DEFORM is applied to analyze the metal flow of tooth, and these analytical results are verified by thread rolling experiment for spindle screw.