• 한국초전도ㆍ저온공학회논문지
• /
• 제20권4호
• /
• pp.26-30
• /
• 2018

The turn-to-turn contact resistance of 2G high temperature superconducting (HTS) coils with metal insulation (MI) is closely related to the stability of the coils, current charging rate and delay time [1]. MI coils were fabricated using five kinds of metal tapes such as aluminum (Al) tape, brass tape, stainless steel (SS) tape, copper (Cu)-plated tape and one-sided Cu-plated SS tape. The turn-to-turn contact surface resistances of co-winding model coils using Al tape, brass tape, and SS tape were 342.6, 343.6 and $724.8{\mu}{\Omega}{\cdot}cm^2$, respectively. The turn-to-turn contact resistance of the model coil using the one-sided Cu-plated SS tape was $ 248.8{\mu}{\Omega}{\cdot}cm^2$, which was lower than that of Al and brass tape. Al or brass tape can be used to reduce contact resistance and improve the stability of the coil. Considering strength, SS tape is recommended. For strength and low contact resistance, SS tape with copper plating on one side can be used.

• 한국자기학회지
• /
• 제6권1호
• /
• pp.21-27
• /
• 1996

초미립 자성 입자를 이용한 MP(metal particle) 테이프의 특성을 개선하기 위하여, 제조 공정상의 여러가지 인자의 영향을 조사하였다. kneading 조건, milling 고형분, coating 두께, 배향조건, calender 조건, 경화 조건 등 주요 제조 조건에 따른 MP 테이프의 휘도(luminance) S/N, RF 재생 출력등의 전자 변환 특성과 광택, 점도, 강성 (stiffness)등의 물리특성이 조사하였으며, 이로부터 각 공정의 최적 제조 조건을 결정하였다. 이상의 제조 공정 조건으로 제조된 테이프는 High Band 8 mm 비디오 테이프에서 요구되는 전자변환특성, 툴리특성 및 내구성 등의 기본특성을 모두 만족하였다.

• 한국자기학회지
• /
• 제6권1호
• /
• pp.28-35
• /
• 1996

자기 테이프 제조용 초미립 자성 철 분말의 분산 거동을 파악하기 위하여 vinyl계 바이더, polyurethane 바인더, 윤활제등 첨가제 종류 및 양에 따른 분산 거동 및 물리특성들을 조사하였다. 분산성은 바인더의 funtional group의 종류, 자성체와 바인더의 비율등에 크게 영향을 받았으며 적정 조건의 선택으로 분산성은 종래보다 20% 증가하 였다. 이에 따라 자기 특성중 포화 자화는 종래의 경우보다 200 Gauss 증가하였으며, 전자 변환 특성중 휘도 S/N (signal to noise ratio)은 2dB 증가하였다. 적절한 윤활제의 종류및 양에 따라 tape의 마찰계수는 0.15 감소하였으며, 이에 따라 tape의 내구성중 휘도 S/N 열화특성이 4dB 이상 향상되었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제8권1호
• /
• pp.1-4
• /
• 2006

The $MgB_2$ tapes with several metal powder addition were fabricated by PIT method with or without heat treatment. The $J_c$ value of $5.600A/cm^2$ and $16.000A/cm^2$ at 4.2 K and 5 T were obtained for the $MgB_2$ tape and 10 vol % of Cu added $MgB_2$ tape without heat treatment respectively. The $J_c$ value of $8.000A/cm^2$ and $35,000A/cm^2$ at 4.2 K and 5 T were obtained for the $MgB_2$ tape and 10 vol. % of Al added $MgB_2$ tape with heat treatment, respectively. The $J_c-B$ curve shows enhancement in $J_c$ under magnetic field. which suggests enhancement in workability and grain connectivity with several metal powder addition.

• 한국초전도ㆍ저온공학회논문지
• /
• 제12권4호
• /
• pp.17-19
• /
• 2010

In this work, the optimized process condition of chemical solution deposition which is used to planarize the surface of the metal tape (which is used to grow IBAD-MgO texture template) was investigated. $Y_2O_3$ films were dip-coated on the surface of the unpolished metal tape as the seed and barrier layer. The effects of $Y_2O_3$ concentration of the solution (0.5wt.%, 1.3wt.%, 2.8wt.%, 5.6wt.%) and the number of coatings on the surface morphology and barrier capability against the diffusion from the metal tape were examined. The surface morphology and the thickness of the film were observed using the scanning electron microscope and the atomic force microscope. The presence of elements in metal tape on the film surface was analyzed using the auger electron spectroscopy. The $Y_2O_3$ film thickness increases with increasing the $Y_2O_3$ concentration in the solution, and the surface became smoother with increasing the number of coating cycles. The best result was obtained from the $Y_2O_3$ film coated 4 cycles using 2.8wt.% solution.

• Progress in Superconductivity
• /
• 제1권2호
• /
• pp.120-124
• /
• 2000

Ni-13%Cr and Ni-70%Cu alloy tapes were prepared by using high purity metal powders as starting materials. The Ni-13%Cr and the Ni-70%Cu mixtures were isostatically pressed, sintered, rolled and texture-annealed. SEM EDS analysis showed that copper and nickel atoms were completely mixed, while the alloying between the chromium powders and the nickel powders was incomplete. In spite of incomplete alloying between nickel and chromium powders, sharp cube-texture was developed for the Ni-13%Cr tape as well as the Ni-70%Cu tape.

• 한국초전도ㆍ저온공학회논문지
• /
• 제6권4호
• /
• pp.13-16
• /
• 2004

Three film deposition systems (pulsed laser deposition, sputtering, and evaporation) equipped with reel-to-reel metal tape moving apparatus were installed and used to make meter-long coated conductor. Buffer architecture of $CeO_2/YSZ/Y_2O_3$ was deposited on Ni alloy using sputtering, evaporation, and PLD. YBCO superconducting layer was continuously deposited on buffered metal tape by PLD. End-to-end critical current ($I_c$) of 107 A at 77 K, self-field has been achieved in 1 em-wide tape (thickness 0.6∼1.0${\mu}{\textrm}{m}$, tape moving speed 54∼72 cm/hr) over 1 meter length.

• Corrosion Science and Technology
• /
• 제3권5호
• /
• pp.194-197
• /
• 2004

The corrosion resistance of several kind of ME (Metal Evaporated) tape has been investigated both in mild sulfuric acid solution and NaCl solution by electrochemical impedance spectroscopy. It was found that the degradation of ME tapes was accelerated with increasing the concentration of sulfuric acid. There was no significant change in corrosion resistance when the concentration of NaCl was under 3.5 wt%. However, the impedance value decreased when the concentration of NaCl was up to 10 wt%. The degradation of backside of ME tapes was also investigated by AC impedance measurements. The results showed that the impedance behavior of backside plastic film changed with the concentration of sulfuric acid even at the beginning of immersion, implying the changing of the permeability for the backside of ME tapes. It was also found that the corrosion resistance of DVC (Digital Video Cassette) ME tape was better that that of Hi-8mm ME tapes in sulfuric acid solutions. Also, the backside of DVC ME tape showed better water resistance than that of Hi8 ME tapes.

• 한국산학기술학회논문지
• /
• 제4권3호
• /
• pp.284-288
• /
• 2003

본 논문에서는 유궤도 이동로봇의 이점을 활용하고 궤도의 유연성을 높여주기 위해 금속 테잎형태의 유궤도를 갖는 이동로봇 시스템을 제작하였다 제작된 무인 운반용 이동로봇은 초음파 및 광(적외선)센서가 탑재된 센서부, 모터 및 엔코더로 이루어진 모터부. 사용자 인터페이스부, 중앙제어부, 컴퓨터 인터페이스부로 구성된다. 초음파센서를 이용하여 이동 경로상의 장애물을 감지하고, 광(적외선)센서를 이용하여 금속 테잎의 궤도를 정확히 감지하여 원하는 위치에 이동할 수 있도록 하였다 개발된 유궤도 이동로봇은 금속 테잎형태의 궤도를 사용함으로써 궤도의 유연성을 높여줄 백만 아니라 무인 이동로봇들의 하드웨어적 소프트웨어적인 비용을 상당부분 절감할 수 있도록 하였다.

• 한국음향학회지
• /
• 제11권2호
• /
• pp.28-37
• /
• 1992

본 연구에서는 압전 특성이 우수한 PZT계 압전세라믹스를 원판상으로 박판화하여 금속 진동판에 부착시킨 PZT/Metal음향변환기를 제작하였다. 이 때 압전 세라믹스를 박판화하기 위해 'tape casting 방법‘을 사용했으며, 제작된 PZT/Metal 음향 변환기를 압전 부자, 압전 스피커등의 소자에 응용 시키기 위해 음향특성을 연구하였다. 연구 결과, 세라믹스의 압전 계수($d_{31}$)이 증가함에 따라 레벨(dB)이 -6dB에서 - 14dB로 증가된다. 음향 변환기의 직경비 ${\eta}$가 0.7-08이고, 두꺼비 (${\beta}$)가 1일 때 최적 음압 특성을 나타냈으며, 음압은 -15~-16dB정도이었다.