• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.3
• /
• pp.79-86
• /
• 1992

The cause of excess current noise which appears some times in RuO$_2$ thick film chip resistors and the process to reduce such noise are investigated. We observed that too large thermal expansion coefficients of resistor paste and electrode metal paste can induce the mechanical stress and microcracks in the contact region of the two sintered materials. Such microcracks result in the reduction of conduction paths in the sintered electrode and this provokes the increase of the resistance value and the current noise. Such excessive current noise induced by microcracks could be reduced or even eliminated by using an enlarged overcoat patterns in the plating process or by adding an additional annealing process before plating.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.11
• /
• pp.6015-6022
• /
• 2013

It has been known that there are large amount of nitric acid and valuable metals, copper in the plating waste solution of automobile wheel. As nitric acid and valuable metals are high price and toxic, they should be recovered for economics and environment. Plating waste was extracted with TBP diluted with kerosene. The concentration of nitric acid in aqueous phase was analyzed by titration method by NaOH solution (0.1~1.0N) and the amount of metals by ICP-MS and ICP-AES. The concentration of copper in plating waste were 76,850 mg/L. The concentration of nitric acid in plating waste was 1.02 M. After three step extraction was performed with 50% TBP, each organic phase was stripped three times with distilled water to obtain 48.1% of nitric acid. Purity of final nitric acid was over 99.9% by ICP analysis. After recovery of nitric acid, copper was extracted with various solvent extractors like PC 88A, D2EPHA, LIX 84 and ISE 106. Among these extractors, 92% of copper was recovered by ISE 106 after 1st extraction and 30% $H_2SO_4$ stripping. Copper ion was reduced with $N_2H_4$ to make metal powders, respectively.

• Membrane and Water Treatment
• /
• v.10 no.3
• /
• pp.239-244
• /
• 2019

Plating wastewater containing various heavy metals can be produced by several industries. Specifically, we focused on the removal of copper (Cu2+) and nickel (Ni+) ions from the plating wastewater because all these ions are strictly regulated when discharged into watershed in Korea. The application of both nanofiltration (NF) and reverse osmosis (RO) technologies for the treatment of wastewater containing copper and nickel ions to reduce fresh water consumption and environmental degradation was investigated. In this work, the removal of copper (Cu2+) and nickel (Ni+) ions from synthetic water was studied on pilot scale remove by before using two commercial nanofiltration (NF) and reverse osmosis(RO) spiral-wound membrane modules (NE2521-90 and RE2521-FEN by Toray Chemical). The influence of main operating parameters such as feed concentration on the heavy metals rejection and permeate flux of both membranes, was investigated. Synthetic plating wastewater samples containing copper ($Cu^{2+}$) and nickel ($Ni^{2+}$) ions at various concentrations(1, 20, 100, 400 mg/L) were prepared and subjected to treatment by NF and RO in the pilot plant. The results showed that NF, RO process, with 98% and 99% removal for copper and nickel, respectively, could achieve high removal efficiency of the heavy metals.

• Korean Journal of Materials Research
• /
• v.23 no.11
• /
• pp.661-665
• /
• 2013

We investigated the characteristics of electroless plated Cu films on screen printed Ag/Anodized Al substrate. Cu plating was attempted using neutral electroless plating processes to minimize damage of the anodized Al substrate; this method used sodium hypophosphite instead of formaldehyde as a reducing agent. The basic electroless solution consisted of $CuSO_4{\cdot}5H_2O$ as the main metal source, $NaH_2PO_2{\cdot}H_2O$ as the reducing agent, $C_6H_5Na_3O_7{\cdot}2H_2O$ and $NH_4Cl$ as the complex agents, and $NiSO_4{\cdot}6H_2O$ as the catalyser for the oxidation of the reducing agent, dissolved in deionized water. The pH of the Cu plating solutions was adjusted using $NH_4OH$. According to the variation of pH in the range of 6.5~8, the electroless plated Cu films were coated on screen printed Ag pattern/anodized Al/Al at $70^{\circ}C$. We investigated the surface morphology change of the Cu films using FE-SEM (Field Emission Scanning Electron Microscopy). The chemical composition of the Cu film was determined using XPS (X-ray Photoelectron Spectroscopy). The crystal structures of the Cu films were investigated using XRD (X-ray Diffraction). Using electroless plating at pH 7, the structures of the plated Cu-rich films were typical fcc-Cu; however, a slight Ni component was co-deposited. Finally, we found that the formation of Cu film plated selectively on PCB without any lithography is possible using a neutral electroless plating process.

• Laser Solutions
• /
• v.3 no.2
• /
• pp.25-33
• /
• 2000

One of perspective direction of microfabrication is direct laser writing technology that allows to create metal, semiconductive and dielectric micropatterns on substrate surface. In this work, a two step method, the combination of seed forming process, in which metallic Al seed was selectively generated on AlN ceramic substrate by direct writing technique using a pulsed Nd : YAG laser and subsequent electroless Ni plating on the activated Al seed, was presented. The effects of laser parameters such as pulse energy, scanning speed and pulse frequency on shape of Alseed and conductor line after electroless Ni plating were investigated. The nature of the laser activated surface is analyzed from XPS data. The line width of this metallic Al and Ni is analyzed using SEM. As a results, Al seed line with 24㎛ width and 100㎛ isolated line space is obtained. Finally, laser direct writing can be applied in the field between thin and thick film technique in electronic industry.

• Journal of Welding and Joining
• /
• v.21 no.4
• /
• pp.31-38
• /
• 2003

Line heating is an effective and economical process for forming flat metal plates into three-dimensional shapes for plating of ships. Because the nature of the line heating process is a transient thermal process, followed by a thermo elastic plastic stress field, predicting deformed shapes of plate is very difficult and complex problem. In this paper, neural network model o3r solving the inverse problem of metal forming is proposed. The backpropagation neural network systems for determining line-heating positions from object shape of plate are reported in this paper. Two cases of the network are constructed-the first case has 18 lines which have different positions and directions and the second case has 10 parallel heating lines. The input data are vertical displacements of plate and the output data are selected heating lines. The train sets of neural network are obtained by using an analytical solution that predicts plate deformations in line heating process. This method shows the feasibility that the neural network can be used to determine the heating-line positions in line heating process.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.8
• /
• pp.11-17
• /
• 2001

Industrial use of physical vapor deposition(PVD) has been widely expanded during last two decades, and in the mean time plasma assistance in PVD has become an essential tool in preparing compound films with dense microstructure. The principles of electron beam-based plating, balanced and unbalanced magnetron sputtering and cathodic arc deposition. consisting three basic configuration of plasma assisted PVD(PAPVD)process, were reviewed. Recent technical development in PVD coating process were discussed. This paper tries to show tendency for developing new coating film on cutting tools.

• Journal of Surface Science and Engineering
• /
• v.27 no.3
• /
• pp.143-148
• /
• 1994

Effects of process variables of HCD ion plating on the film composition of Ti(C, N) were analyzed. The mole ratio of carbon to nitrogen and that of non-metal to titanium in the film primarily depend on the partial pressure ratio of ($C-2H_2$/ $N_2$) and total reactive gas pressure, respectively. The amount of nonmetallic com-ponents increases in nonlinear fashion as the total gas pressure due to the different reactivity of $C-2H_2$ and $N_2$ gases with Ti. The nonmetallic components was saturated dwith nitrogen when the nitrogen gas was more than 60% of total reactive gas. These two process variables could be related systematically using the concept of effective pressure in which the difference of reactivity of each gas was normalized.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.96-101
• /
• 2011

The thin films of TiN have been used extensively as wear-resistant materials, for instance, such as tools of high-speed cutting, metal mold forming etc. In these days, because the thin films capable of being used more severe conditions are needed, the technologies of arc ion plating are tried to improve its characteristics. The purpose of this study is to investigate the characteristics of thin films of (Ti,Cr)N compared with those of TiN. The method of arc ion plating, which is known as showing good tight-adherence and productivity, was used. After manufacturing thin films of ($Ti_{1-x}Cr_{x}$)N (x=0~1) with change of Cr in (Ti,Cr) target, atomic concentration, structure, size of crystallite, residual stress and surface roughness of thin films on substrate were investigated. As the results, it was confirmed that Cr atomic concentrations of thin films were proportionally changed with Cr atomic concentrations of target, and thin films of ($Ti_{1-x}Cr_{x}$)N (x=0~1) showed NaCl type and CrN existed as solid solution to TiN.

• Laser Solutions
• /
• v.12 no.4
• /
• pp.6-11
• /
• 2009

The LDS(Laser Direct Structuring) process uses thermoplastic polymers with a additive compound that serves as plating seed after the activation by laser. It can realize industry requirement such as miniaturization of electrical component, design flexibility and reduction of production steps. The purpose of this study is to introduce LDS, and to investigate the fundamental mechanism. Also the characteristics of conductive patterns were investigated with respect to laser fluence and intensity. We have used a pulsed fiber laser (wavelength : 1064nm) and copper electroless plating to fabricate conductive patterns. The result showed that laser induced metal-organic complex was caused metalization by electroless copper plating, the critical laser fluence was $1.41\;J/cm^2$ at a scan speed of 1 m/s.