• Journal of Environmental Science International
• /
• v.15 no.1
• /
• pp.1-7
• /
• 2006

The purpose of this study is to illustrate the characteristics of soil organic matter (SOM) and partition coefficient $(K_{DOC})$. Humic substances (HS) from eight soils of varying properties were extracted by two different methods. The dissolved organic carbon (DOC) concentration was stabilized in 22hrs. The ratio of UV absorbance at 465nm and 665nm (E4/E6 ratio) for HS were similar pattern for 8 soils. The extraction with increasing pH increased dissolution of SON. The ratio of organic carbon (OC) associated with HA and FA (the HA:FA ratio) was varied widely in accordance with the soils and was highly correlated to OC $content(\%)$ of the soils. in modeling metal speciation in soils and soil solutions, assumptions that all DOC in soil solution is associated with FA and that HA:FA ratio in SOM is constant have been made. The results of this study indicate that the validity of these assumptions is questionable. By sequential pH extraction, the $K_{DOC}$ showed in a linear correlation with pH.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.4
• /
• pp.327-331
• /
• 2008

An in-line wet etch/cleaning system was established for the research and development in wet etch process as a formation of electrode such as metal or transparent conductive oxide layer. A reverse moving system was equipped in the in-line wet etch/cleaning system for the alternating motion of glass substrate in a wet etch bath of the system. Therefore, it was possible for the glass substrate to be moved back and forth and it was possible to reduce the size of the system by using the reversing moving system. For the effect of the alternating motion of substrate on the etch rate in the in-line wet etch bath, indium tin oxide(ITO) patterns were obtained through wet etch process in the in-line system in which the substrate was moved back and forth. From the CD(critical dimension) skews resulted from the ADI CD and ACI CD of the ITO patterns, it was concluded that the alternating motion of glass substrate are possible to be applied to the mass production of wet etch process.

• Journal of Korea Foundry Society
• /
• v.13 no.3
• /
• pp.268-275
• /
• 1993

In gravity die casting, die cooling systems are frequently employed with water cooling to remove the heat of the solidifying metal. Thermal modeling is an important technique in mold design for improving the productivity of the process. Computer simulation system which consists of pre-processor, main solidification simulator and post-processor has been developed for three dimensional solidification analysis of cyclic gravity die casting. The pre-processor is used for mesh generation in a PC system. The modified finite difference method is adopted for the main solidification simulation algorithm during all the casting cycles. The post-processor graphically presents the simulation results. Several experiments in automotive cast piston were carried out. The temperature variations in casting and mold with time are measured experimentally, and the results are compared with calculation results. The effects of cycle number on solidification pattern are also studied. Several experimental results for the prediction of shrinkage defects are compared with calculated results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.7
• /
• pp.999-1005
• /
• 2004

A new stamp fabrication technique for the soft lithography has been developed in the range of several microns by means of a nano-replication printing (nRP) process. In the nRP process, a figure or a pattern can be replicated directly from a two-tone bitmap figure with nano-scale details. A photopolymerizable resin was polymerized by the two-photon absorption which was induced by a femtosecond laser. After the polymerization of master patterns, a gold metal layer (about 30 ㎚ thickness) was deposited on the fabricated master patterns for the purpose of preventing a join between the patterns and the PDMS, then the master patterns were transferred in order to fabricate a stamp by using the PDMS (poly-dimethylsiloxane). In the transferring process, a few of gold particles, which were isolated from the master patterns, remained on the PDMS stamp. A gold selective etchant, the potassium iodine (KI) was employed to remove the needless gold particles without any damage to the PDMS stamp. Through this work, the effectiveness of the nRP process with the PDMS molding was evaluated to make the PDMS stamp with the resolution of around 200 ㎚.

• Journal of Power System Engineering
• /
• v.3 no.2
• /
• pp.57-63
• /
• 1999

The fabrication of $Al_2O_3/Al$ composites by pressureless infiltration technique was made to investigate the effects of processing variables such as content of Mg, processing temperature and time on the infiltration behavior of molten Al and microstructure. When the pure Al was infiltrated into mixtures of Mg and $Al_2O_3$ powder, processing temperature required to spontaneous infiltration was decreased and critical processing temperature and Mg content were $700^{\circ}C$ and 3wt% respectively. The content of Mg was found the most powerful variable for infiltration of molten Al. The infiltration ratio increased with Mg content and processing temperature, however the $Al_2O_3/Al$ composites which were fabricated by high Mg content and processing temperature resulted in non uniform dispersion of $Al_2O_3$ particles by excessive interfacial reaction. XRD pattern indicated that $MgAl_2O_4$ and AIN was observed at the interface of $Al_2O_3$ particles and in the Al matrix as reaction products.

• Journal of ILASS-Korea
• /
• v.2 no.4
• /
• pp.29-35
• /
• 1997

Liquid film thickness is measured by $moir\acute{e}$ topography which monitored liquid surface. $Moir\acute{e}$ fringe measurement techniques share the inherent simplicity found in optical interferometric techniques have the advantage of use over a greater range of displacement. $Moir\acute{e}$ fringe are the geometric interference patterns observed when two dense line grating are superposed. Light transmitted through a fixed line grating is deviated by the liquid film surface, producing a distored image of the grating. The $moir\acute{e}$ fringe produced by projection of this optically distored grating onto a second stationary grating permit visualization of the liquid surface and measurement of the liquid film thickness. This study measured the small amplitude of liquid film thickness to the $moir\acute{e}$ fringe pattern produced when spherical metal was dropped glycerin put)1 And the measurement of liquid film thickness flowing down an inclined plate are required to calculate the liquid slope in a position.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.260-266
• /
• 2012

Syngas and hydrogen from the $CeO_2/ZrO_2$ coated foam devices were investigated under simulated solar radiation. The $CeO_2/ZrO_2$ coated SiC, Ni and Cu foam device were prepared using drop-coating method. Syngas production step was performed at $900^{\circ}C$, and hydrogen production process was performed for ten repeated cycles to compare the CeO2 conversion in syngas production step, $H_2$ yield in hydrogen production step and cycle reproducibility. The produced syngas had the $H_2$/CO ratio of 2, which was suitable for methanol synthesis or Fischer-Tropsch synthesis process. In addition, syngas and hydrogen production process is one of the promising chemical pathway for storage and transportation of solar heat by converting solar energy to chemical energy. After ten cycles of redox reaction, the $CeO_2/ZrO_2$ was analyzed using XRD pattern and SEM image in order to characterize the physical and chemical change of metal oxide at the high temperature.

• Journal of Sensor Science and Technology
• /
• v.17 no.1
• /
• pp.9-14
• /
• 2008

In this paper, the gas responses of tungsten oxide films prepared by anodic reaction was discussed. Sensing electrodes and heating electrodes were patterned by photolithography method on quartz substrate. Porous tungsten oxide was fabricated in electrolyte solutions of 5 % HF (HF :$C_2H_6OH:H_2O$=3 : 2 : 20) by anodic reaction. The anodic reaction with metal (platinum wire) as a cathode and the sensing device as an anode was conducted under the various reaction times (1-10 min) at 10 mA/$cm^2$ The surface structure and morphology of the fabricated sensor have been analysed by X-ray diffraction (XRD) and field-emission scanning electron microscopy (FE-SEM). All the peaks of XRD results were well indexed to the pure phase pattern. The average diameter of the porous tungsten oxide surface were ranged about 100 nm. The fabricaed sensor showed good sensitivity to 200 ppm toluene at operating temperature of $250^{\circ}C$.

• Toxicological Research
• /
• v.24 no.4
• /
• pp.297-305
• /
• 2008

This study was carried out to measure the concentration of heavy metals (Pb, Mn, Cr, Cd, Ni, Zn, and Cu) in water and Bolti fish (Tilapia nilotica) samples collected from Rasheed branch of River Nile, north of El-Giza Governorate, Egypt by atomic absorption spectrophotometry. The investigated districts through which the branch passes include El-Manashi, Gezzaya, El Katta, Abo Ghaleb and Wardan. Based on WHO and FAO safety reference standards, the results of the current study showed that water and fish tissues were found to contain heavy metals at significantly variable concentration levels among the investigated districts. They were polluted with respect to all the metals tested at Gezzaya district. However, the levels of analyzed metals in water and fish tissues were found lower than legal limits in other districts. The heavy metals showed differential bioaccumulation in fish tissues of the different districts as the accumulation pattern (as total heavy metal residues) was district dependant as follow: Gezzaya > Wardan > El Katta > Abo Ghaleb > El Manashi.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.3
• /
• pp.23-30
• /
• 2012

In this paper, we propose a new near-field reader antenna for 900 MHz RFID. The proposed antenna consists the micro-strip antenna with the periodic structure. The overall dimension of the antenna is $313mm{\times}152mm{\times}14mm$. The antenna has the uniform E-field distribution in near field region and the heart-shaped radiation beam pattern (Peak gain=-2 dBi). The transmitted power range is from 17 dBm to 23 dBm. We focus on minimizing the detected error by suppressing the reflected power from the metal, which is attached to the surface by tag, and by reducing the transmitted power from tag.