• 한국융합학회논문지
• /
• 제10권12호
• /
• pp.257-262
• /
• 2019

최근 취미로 다양한 레포츠를 즐기는 인구가 증가하였다. 그에 따라 차량 지붕위에 다양한 물건들을 적재한 차량들을 거리에서 쉽게 볼 수가 있다. 차량 지붕위에 적재를 할 수 있게 하는 장치는 랙 이라는 장치이며 차량마다 각기 다른 형상을 가지고 있다. 다양한 종류들이 있지만 무거운 짐을 적재하기 위해 강도 및 내구성을 가져야 한다. 본 연구에서는 루프 랙의 지지대 방식과 고정대의 형상에 따른 구조 해석을 하였다. 세 가지의 모델들 중, Model C가 가장 좋은 내구성을 가지고 있음을 보였다. 따라서 어떤 형상을 가진 루프랙이 가장 안정성이 있는 것을 본 연구 결과로서 알 수 있다. 본 결과를 토대로 얻은 자동차 루프랙의 형상에 따른 구조 해석에 통한 융합 연구에 대한 설계데이터를 활용함으로서 실생활에서의 자동차 부품에 융합하여 그 미감을 보일 수 있다.

• 한국융합학회논문지
• /
• 제10권12호
• /
• pp.281-286
• /
• 2019

자동차의 하부를 수리하기 위해서는 차 밑으로 들어가야 된다. 그러나 이 작업은 수리공이 수리하기에 불편하기도 하고 사고를 일으킬 수도 있다. 이러한 난제들을 해결하기 위하여 개발된 장비가 자동차의 리프트이다. 본 연구에서는 세 가지의 자동차의 리프트 Model 1, 2, 3을 설계하였다. 구조용 강의 물성치를 모델들에 적용하고 동일한 조건으로 같은 하중을 가하여 해석을 하였다. Model 2, 3이 Model 1보다 더 적은 구조적 변형을 보였으며 Model 2, 3이 Model 1보다 구조적으로 더 안정적인 것을 나타냈다. 본 연구결과를 토대로 얻은 자동차 리프트 형상에 따른 내구성 해석을 통한 융합 연구에 대한 설계데이터를 활용함으로서 실생활에서의 자동차 수리 기자재 부품에 융합하여 그 미감을 보일 수 있다.

• 구강회복응용과학지
• /
• 제21권1호
• /
• pp.69-81
• /
• 2005

The objective of this study was to evaluate the toothbrush abrasion characteristics of class V restorations. Thirty extracted human premolars, which were collected from oral surgery clinics were used. We mounted five teeth in a metal ring mold of 50 mm in diameter and 15 mm in height using chemically cured acrylic resin. Class V cavities were prepared in lingual cervical root surfaces and restored using one of following restorative materials : Dentin Conditioner/Fuji II LC (Group FL), All Bond II/Z-250 (Group ZT), One-up Bond F/Palfigue Estelite (Group PE), F2000 Primer/Adhesive (Group FT), and Prime & Bond 2.1/Dyract AP (Group DR). They were stored under distilled water at $37^{\circ}C$ for seven days. The toothbrush abrasion test was conducted using a wear testing machine of pin-on disk type under a load of 1.5 N for 100,000 cycles. We have examined the bonded interfaces, the changes of surface roughness and color of abraded surfaces. From this experiment, the following results were obtained. 1. The change of surface roughness showed high degree: RMGIC>compomer>composite resin (p<0.05). 2. Because of the protrusion and missing of filler particles, SEM observation of abraded surfaces of RMGIC and compomers revealed the increase of surface roughness due to the selective removal of matrix resin. 3. The color change by toothbrush abrasion was affected in large part by the change of $L^*$ and $b^*$ of resin composites (p<0.05). 4. The color change by toothbrush abrasion was so small to detect by human eyes. 5. SEM observation of abraded surfaces revealed the interface bonding was the best in the FT group.

• 대한치과기공학회지
• /
• 제34권2호
• /
• pp.75-81
• /
• 2012

Purpose: All ceramic crown, made from zirconia instead of metal for core material, is recognized the best esthetical prosthesis. Recently, high-priced zirconia blocks and expensive CAD/CAM machines come into use for making zirconia core. In this study, slip casting process is adapted to evaluate the possibility of the recycling the remained parts of zirconia block after machining. Methods: Remained zirconia blocks were reduced to powders with zirconia mortar, and screened with 180 mesh sieve. Passed powders were ball milled under various conditions to obtain the optimum zirconia slip for casting. Solid casting method was used for casting the specimens with plaster mold. Formed specimens were dried and biscuit fired at $1,000^{\circ}C$ for 1 hour. Biscuit fired specimens were finished with exact shape of square pillar. Finished specimens were fired from $1,200^{\circ}C$ to $1,550^{\circ}C$ at $50^{\circ}C$ intervals for 1 hour. Linear shrinkage, apparent porosity, water absorption, bulk density, and flexural strength were tested. Microstructures were observed by SEM. Results: Above examinations indicated that the optimum firing temperture was $1,500^{\circ}C$, and when fired at this temperature for 1 hour, apparent porosity was 0% and flexural strength was 680MPa. SEM photomicrographs showed uniform 200~300nm grain size, which is equal with microcture of sintered commercial zirconia block. when compare 24% linear shrinkage of cast specimen with 20% linear shrinkage of CAD/CAM machined block, it was estimated that the size controlling of cast core was not so difficult. Conclusion: According to the all of this experimental results, the cast zirconia core produced from the remained parts of zirconia block was possible to use for all ceramic denture.

• 대한기계학회논문집A
• /
• 제35권11호
• /
• pp.1399-1406
• /
• 2011

수처리 공정에는 반드시 교반기 전용 감속기가 사용된다. 본 연구에서는 사용 중의 누유를 방지하고 토크효율 향상을 위한 전용 누유방지형 감속기를 개발하였다. 설계 개선된 감속기 시제품을 개발하는데 있어서, CAD 및 CNC 고속가공기를 사용하여 실물모형(Mock up), 금형 등을 제작하였다. 특히 누유방지 구조인 감속기 시제품의 하부 하우징에 대한 구조적 안전성을 평가하고자 상용 유한요소 해석코드인 ALGOR 을 이용하였다. 해석 결과, 최대 von Mises 응력이 항복응력보다 낮은 123 N/$mm^2$ 으로 안전하였으며, 고유진동수는 650~700 Hz 이었다. 그리고 토크효율은 95.87%로서 이전 연구결과 (88.45%)에 비하여 약 8% 향상되었다. 소음 수준은 75 dB, 사용 중 누유 및 이상 소음은 발생하지 않았다. 따라서 항상된 감속기 시제품을 최적 설계하여 성공적으로 개발하였다.

• 한국주조공학회지
• /
• 제37권3호
• /
• pp.71-77
• /
• 2017

Casting defects produced during the casting process seriously affect the mechanical properties of the resulting products, reduce the performance capabilities of the product, and also result in economic losses. Therefore, this paper mainly investigates the causes of defects and methods by which to reduce these defects stemming from molten metal flows in a runner system of the type widely used in the sand mold casting process. The flow characteristics of a molten alloy are difficult to observe during the actual casting process. For this reason, a water model was used to observe the flow in the casting process, and the flow in each case was recorded using high-speed cameras as part of the experimental process of this study. Several repetitive experiments were performed to improve the accuracy of the experimental results. The traditional casting system was modified according to the design rules proposed by Campbell, and the system was termed flow-adaptive gating system with a water model. Comparing the flow characteristics of traditional and adaptive gating systems with a water model shows that the bubbles in the water in the latter case are reduced more significantly than in the former case. A ceramic filter system was adapted to the flow-adaptive gating system to minimize the instability of the flow during filling, which occurs as the fluid velocity in the runner increases. In additional, the flow behavior with and without the filter system were compared. The water model system in this work was shown to be able to verify that the adaptation of the filter system brings improvements by stabilizing the flow and reducing the amount of bubbles in the runner system. Moreover, using the flow-adaptive runner system with the filter system leads to considerably stable flows in the runner system.

• 한국공작기계학회논문집
• /
• 제17권1호
• /
• pp.7-15
• /
• 2008

Currently existing high-accuracy and high-speed die sets used in reciprocal press create scratches at the surface of guide posts, steel balls, and bushes due to vertical movement of balls with point-contacts between inner surface of bushes and guide posts. Consequently, accuracy of the die set and the life span of the metal mold are reduced. However, those scratches could reduce the pre-load of the steel ball. This research designed and developed a groove-type die set which improves life span of the die set by eliminating point-contacts of steel balls with guide posts. The guide post consisted of a steel-ball retainer, a steel-ball retainer stopper, a guide bush, a guide pin, a snap ring, and a spring. The steel-ball retainer has 72 holes with 8 columns of 9 holes in each column. The inner surface of the guide bush was grinded(surface roughness: $Ra\;\\;0.2{\mu}m$, accuracy: $0\;{\sim}\;-0.002mm$) after NC turning and heat treatment. Also, a line of small intermediate pocket was processed inside of the guide bush for lubrication and elimination of foreign materials. Guide grooves of steel balls were processed using a wire EDM(Electrical Discharge Machining) after heat treatment. With such a design of the guide post stated above, loads against steel balls could be dispersed greatly by the line contacts through the guide groove between the guide post and the guide bush, and the life span of the guide post could be expanded semi-permanently.

• 대한기계학회논문집
• /
• 제17권6호
• /
• pp.1412-1422
• /
• 1993

본 연구는 각주형 금형부품을 절삭가공할때 부품의 설계데이터로부터 부품의 형상적인 특징을 추출하여 공정설계시스템인 MOLDCAPP과 작업설계시스템인 COPS에서 사용할 수 있는 정보를 생성함으로써 CAD/CAM의 연결을 자동화할 수 있는 특징형상 인식 시스템을 개발하는 연구로, 특징형상 인식기법의 창안보다는, 가용한 기술의 장 점을 사용하여 각주형 공작물의 기계 절삭가공으로 생성될 수 있는 형상을 특징형상으 로 정의하고 ACIS로 설계된 CAD데이터로부터 정의된 특징형상을 추출하여 각 특징형상 들의 형상 데이터를 결정함으로써 MOLDCAPP, COPS 등의 공절설계시스템의 입력데이터 를 생성할 수 있도록 Fig.1과 같이 설계하였다. 특히 PART시스템과 같이 인식대상이 포괄적이지 않으나, 금형부품상의 특징형상으로 범위를 축소하고 금형부품의 가공특징 을 고려하여 인식규칙을 단순화함으로써 금형가공공정의 CAD/CAM연결에 이용될 수 있도록 하였다.

• Restorative Dentistry and Endodontics
• /
• 제15권2호
• /
• pp.17-33
• /
• 1990

The purpose of this study was to evaluate the fracture toughness of dental composite resins and to investigate the filler factor affecting the fracture behaviour on which the degree of fracture toughness depends. Six kinds of commercially available composite resin;, including two of each macrofilled, microfilled, and hybrid type were used for this study, The plane strain fracture toughness ($K_{10}$) was determined by three-point bending test using the single edge notch specimen according to the ASTM-E399. The specimens were fabricated with visible light curing or self curing of each composite resin previously inserted into a metal mold, and three-point bending test was conducted with cross-head speed of 0.1mm/min following a day's storage of the specimens in $37^{\circ}C$ distilled water. The filler volume fractions were determined by the standard ashing test according to the ISO-4049. Acoustic Emission(AE), a nondestructive testing method detecting the elastic wave released from the localized sources In material under a certain stress, was detected during three-point bending test and its analyzed data was compared with, canning electron fractographs of each specimen. The results were as follows : 1. The filler content of composite resin material was found to be highest in the hybrid type followed by the macrofilled type, and the microfilled type. 2. It was found that the value of plane strain fracture toughness of composite resin material was in the range from 0.69 MPa$\sqrt{m}$ to 1 46 MPa$\sqrt{m}$ and highest In the macrofilled type followed by the hybrid type, and the microfilled type. 3. The consequence of Acoustic Emission analysis revealed that the plane strain fracture toughness increased according as the count of Acoustic Emission events increased. 4. The higher the plane strain fracture toughness became, the higher degree of surface roughness and irregularity the fractographs demonstrated.

• Restorative Dentistry and Endodontics
• /
• 제27권1호
• /
• pp.87-94
• /
• 2002

The purpose of this study was to evaluate the color changes of composite resin polymerized with three type of light curing units. Composite resin (Z100, shade A2) were applied in a cylindrical metal mold(2 mm thick, 7 mm diameter). Twenty specimens according to light curing units were made. Group 1 : the specimens were polymerized with Apollo 95E for 3seconds(1370 mW/$\textrm{cm}^2$). Group 2 : the specimens were polymerized with XL 3000 for 40seconds (480 mW/$\textrm{cm}^2$). Group 3 : the specimens were polymerized with Spectrum 800 for 10 seconds(250 mW/$\textrm{cm}^2$) and 30 seconds(700 mW/$\textrm{cm}^2$). The microhardness values(VHN) of upper and lower surfaces specimens after light polymerization were measured for the degree of polymerization. All specimens were stored in distilled water at 6$0^{\circ}C$ for 30 days. The color characteristics(L$^*$, a$^*$, b$^*$) of the specimens before and after immersion were measured by spectrophotometer and the total color difference ($\Delta$E$^*$) was computed. The results obtained were as follows : 1. The microhardness values of Group I showed significantly lower than those of Group II and III (p<0.05). 2. In all groups the $\Delta$E$^*$ values presented below 2.0. 3 Group I showed the highest $\Delta$E$^*$ values followed order from highest to lowest by Group II and III (p<0.05).