• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.270-270
• /
• 2010

결정질 실리콘 태양전지는 표면반사에 의한 광 에너지 손실을 최소화 시키고자 식각을 통한 표면 조직화(texturing)가 이루어진다. 단결정 실리콘 웨이퍼의 경우 알칼리 용액(alkali solution)을 사용하여 이방성 식각(anisotropic etching)을 함으로써 표면에 피라미드를 형성하고 광 포획(light trapping) 효과에 의해 반사율을 줄이게 된다. 그러나 피라미드 형성을 통한 반사율 감소에는 한계를 가지고 있다. Metal assisted etching을 기반으로 한 새로운 형태의 텍스쳐링인 nano texturing은 피라미드가 이루어진 표면에 수많은 nm사이즈의 구조를 형성시킴으로써 표면에서의 반사율을 현저히 감소시킨다. 먼저 $AgNO_3$용액으로 웨이퍼 표면에 Ag입자를 코팅한 후, 그 웨이퍼를 다시 $HF/H_2O_2$ 용액으로 일정시간 동안 식각을 거치게 된다. 그로 인해 표면에는 수 nm 사이즈의 구조물들이 피라미드 위에 생성되고, $AgNO_3$의 농도 및 식각 시간에 따라 그 구조물의 크기 및 굵기가 달라진다. 결과적으로 평균 10%이상의 반사율을 보이던 기존 텍스쳐링 웨이퍼에서 3%이하의 낮은 반사율을 얻을 수 있었다. 또한 이런 nano texturing을 n-emitter 형성 공정 등에 따른 영향과 carrer lifetime에 대하여 연구하였다.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1045-1048
• /
• 2003

In this paper, we studied plasma damage of MIS capacitor with $Al_2$O$_3$ dielectric film. Using capacitor pattern with the same area but different perimeters, we tried to separate etching damage mechanism and to optimize the dry etching process. After etching both metal and dielectric layer by the same condition, leakage current and C-V measurements were carried out for Pt/A1$_2$O$_3$/Si structures. The flatband voltage shift was appeared in the C-V plot, and it was caused by the variation of the fixed interface charge and the interface trapped charge. From I-V measurement, it was found the leakage current along the periphery could not be ignored. Finally, we established the process condition of RF power 300W, 100mTorr, Ar/Cl$_2$ gas 60sccm as an optimal etching condition.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1491-1493
• /
• 2000

Continuing improvement of microprocessor performance involves in the device size. This allow greater device speed, an increase in device packing density, and an increase in the number of functions that can reside on a single chip. However this has led to propagation delay, crosstalk noise, and power dissipation due to resistance-capacitance(RC) coupling become significant due to increased wiring capacitance, especially interline capacitance between the metal lines on the same metal level. So, MSSQ which has the permittivity between 2.5-3.2 is used to prevent from these problems. For pattering MSSQ(Methylsilsequioxane), we use RIE(Reactive Ion Etching) and MERIE(Magnetically enhanced Reactive Ion Etching) which could provide good anisotropic etching. In this study, we optimized the flow rate of $CF_{4}/O_2$ gas, RF power to obtain the best etching rate and roughness and also analyzed the etching result using $\alpha$-step profilemeter, SEM, infrared spectrum and AFM.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.279-280
• /
• 2009

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.160-160
• /
• 2008

In practical etching process, etch ant is sprayed on the metal-deposited panel through nozzles collectively connected to the manifold and that panel is usually composed of many PCB(printed circuit board)'s. The etching uniformity, the difference between individual PCB's on the same panel, has become one of most important features of etching process. In this paper, the prediction of nozzle trajectory has been performed by the combination of algebraic formula and numerical simulation. With the pre-determined geometrical factors of nozzle distribution, the trajectories of individual nozzles were predicted with the change of process operational factors such as panel speed, nozzle swing frequency and so on. As results, two dimensional distribution of impulsive force of etchant spray which could be considered as a key factor determining the etching performance have been successfully obtained. Though only qualitative prediction of etching uniformity have been predicted by the process developed in this study, the expansion to the quantitative prediction of etching uniformity is expected to be apparent by this study.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.74-77
• /
• 2002

Ferroelectric Random Access Memory(FRAM) and MEMS applications require noble metal or refractory metal oxide electrodes. In this study, Ru thin films were etched using $O_2$+10% $CF_4$ plasma in an inductively coupled plasma(ICP) etching system. The etch rate of Ru thin films was examined as function of rf power, DC bias applied to the substrate. The enhanced etch rate can be obtained not only with increasing rf power and DC bias voltage, but also with small addition $CF_4$ gas. The selectivity of $SiO_2$ over Ru are 1.3. Radical densities of oxygen and fluorine in $CF_4/O_2$ plasma have been investigated by optical emission spectroscopy(OES). The etching profiles of Ru films with an photoresist pattern were measured by a field emission scanning electron microscope (FE-SEM). The additive gas increases the concentration of oxygen radicals, therefore increases the etch rate of the Ru thin films and enhances the etch slope. In $O_2$+10% $CF_4$ plasma, the etch rate of Ru thin films increases up to 10% $CF_4$ but decreases with increasing $CF_4$ mixing ratio.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05b
• /
• pp.12-16
• /
• 2001

We investigated the etching characteristics of $YMnO_3$ thin films in high-density plasma etching system. In this study. $YMnO_3$ thin films were etched with $CF_{4}/Ar$ gas chemistries in inductively coupled plasma (ICP). Etch rates of $YMnO_3$ were measured according to gas mixing ratios. The maximum etch rate of $YMnO_3$ is 18 nm/min at $CF_{4}/(CF_{4}+Ar)$ of 20%. In optical emission spectroscopy (OES) analysis, F radical and Ar* ions in plasma at various gas chemistries decreased with increasing $CF_4$ content. Chemical states of $YMnO_3$ films exposed in plasma were investigated with x-ray photoelectron spectroscopy (XPS) and secondary ion mass spectrometry (SIMS). There is a chemical reaction between metal (Y, Mn) and F and metal-fluorides were removed effectively by Ar ion sputtering. $YF_x$, $MnF_x$ such as YF, $YF_2$, $YF_3$ and $MnF_3$ Were detected using SIMS analysis. The etch slope is about $65^{\circ}C$ and free of residues.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.734-737
• /
• 2004

The metal-ferroelectric-semiconductor (MFS) structure is widely studied for nondestructive readout (NDRO) memory devices, but conventional MFS structure has a critical problem. It is difficult to obtain ferroelectric films like PZT on Si substrate without interdiffusion of impurities such as Pb, Ti and other elements. In order to solve these problems, the metal-ferroelectric-insulator-semiconductor (MFIS) structure has been proposed with a buffer layer of high dielectric constant such as MgO, $Y_2O_3$, and $CeO_2$. In this study, the etching characteristics (etch rate, selectivity) of MgO thin films were etched using $Cl_2/Ar$ plasma. The maximum etch rate of 85 nm/min for MgO thin films was obtained at $Cl_2$(30%)/Ar(70%) gas mixing ratio. Also, the etch rate was measured by varying the etching parameters such as ICP rf power, dc-bias voltage, and chamber pressure. Plasma diagnostics was performed by Langmuir probe (LP) and optical emission spectroscopy (OES).

• Journal of Sensor Science and Technology
• /
• v.14 no.6
• /
• pp.423-429
• /
• 2005

In this paper, we proposed the fabrication process of the stable e-beam evaporation and the patterning of metals layer on the polydimethylsiloxane (PDMS) substrate. The metal layer was deposited under the various deposition rate, and its effect to the electrical and mechanical properties (e.g.: adhesion-strength of metal layer) was investigated. The influence of surface roughness to the adhesion-strength was also examined via the tape test. Here, we varied the roughness by changing the reactive ion etching (RIE) duration. The electrode patterning was performed through the conventional photolithography and chemical etching process after e-beam deposition of $200{\AA}$ Ti and $1000{\AA}$ Au. As a result, the adhesion strength of metal layer on the PDMS surface was greatly improved by the oxygen plasma treatment. The e-beam evaporation on the PDMS surface is known to create the wavy topography. Here, we found that such wavy patterns do not effect to the electrical and mechanical properties. In conclusion, the metal patterns with minimum $20{\mu}m$ line width was produced well via the our fabrication process, and its electrical conductance was almost similar to the that of metal patterns on the silicon or glass substrates.

• Journal of Surface Science and Engineering
• /
• v.49 no.1
• /
• pp.98-103
• /
• 2016

The dry etching characteristics of SnO thin films were investigated using inductively coupled plasma (ICP) in Ar, $CF_4$, $Cl_2$ chemistries. the SnO thin films were deposited by reactive rf magnetron sputtering with Sn metal target. In order to study the etching rates of SnO, the processing factors of processing pressure, source power, bias power, and etching gas were controlled. The etching behavior of SnO films under various conditions was obtained and discussed by comparing to that of $SiO_2$ films. In our results, the etch rate of SnO film was obtained as 94nm/min. The etch rates were mainly affected by physical etching and the contribution of chemical etching to SnO films appeared relatively week.