• Smart Structures and Systems
• /
• v.15 no.3
• /
• pp.769-785
• /
• 2015

Although timber structures have been extensively used in underground temporary supporting system, their actual performance is poorly understood, resulting in potentially conservative and over-engineered design. In this paper, a novel wireless sensor technology, SmartPlank, is introduced to monitor the field performance of timber structures during underground construction. It consists of a wooden beam equipped with a streamlined wireless sensor node, two thin foil strain gauges and two temperature sensors, which enables to measure the strain and temperature at two sides of the beam, and to transmit this information in real-time over an IPv6 (6LowPan) multi-hop wireless mesh network and Internet. Four SmartPlanks were deployed at the London Underground's Tottenham Court Road (TCR) station redevelopment site during the Stair 14 excavation, together with seven relay nodes and a gateway. The monitoring started from August 2013, and will last for one and a half years until the Central Line possession in 2015. This paper reports both the short-term and long-term performances of the monitored timber structures. The grouting effect on the short-term performance of timber structures is highlighted; the grout injection process creates a large downward pressure on the top surface of the SmartPlank. The short and long term earth pressures applied to the monitored structures are estimated from the measured strains, and the estimated values are compared to the design loads.

• International Journal of Highway Engineering
• /
• v.15 no.2
• /
• pp.19-27
• /
• 2013

PURPOSES : This study aims to investigate the snow-melt effects of an underground electric heater's snow-melt system via a field performance test, for evaluating the suitability of the system for use on a concrete pavement. The study also investigates the effectiveness of dynamic measures for clearing snow after snowfall events. METHODS : In order to check the field applicability, in November 2010, specimens were prepared from materials used for constructing concrete pavements, and underground electric heating meshes (HOT-mesh) were buried at depths of 50 mm and 100 mm at the site of the Incheon International Airport Construction Research Institute. Further, an automatic heating control system, including a motion sensor and pavement-temperature-controlled sensor, were installed at the site; the former sensor was intended for determining snow-melt effects of the heating control system for different snowfall intensities. Pavement snow-melt effects on snowy days from December 2010 to January 2011 were examined by managing the electric heating meshes and the heating control system. In addition, data on pavement temperature changes resulting from the use of the heating meshes and heating control system and on the dependence of the correlation between the outdoor air temperature and the time taken for the required temperature rise on the depth of the heating meshes were collected and analyzed. RESULTS : The effects of the heating control system's preheat temperature and the hot meshes buried at depths of 50 mm and 100 mm on the melting of snow for snowfalls of different intensities have been verified. From the study of the time taken for the specimen's surface temperature to increase from the preheat temperature ($0^{\circ}C$) to the reference temperature ($5{\sim}8^{\circ}C$) for different snowfall intensities, the correlation between the burial depth and outdoor air temperature has been determined to be as follows: Time=15.10+1.141Depth-6.465Temp CONCLUSIONS : The following measures are suggested. For the effective use of the electric heating mesh, it should be located under a slab it may be put to practical use by positioning it under a slab. From the management aspect, the heating control system should be adjusted according to weather conditions, that is, the snowfall intensity.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.12
• /
• pp.47-56
• /
• 2010

The construction of new roads and the consistent extension of already-existing roads or the line-shape revision of those roads are increased with the governmental investment to SOC facilities currently. Accordingly, the road cut slopes are in the trend of rapidly increasing. As the road slope has increased, a lot of human and property damages has entailed consequently and in the local case, numerous studies have carried out aiming at minimizing this damages caused by the rockfall and landslide. In general, standard falling rock prevention facility has employed for most of the local road slope based on "Guide for Installation and Management of Road Safety Facilities" published by MLTM(the Ministry of Land, Transport, and Maritime Affairs) but profound doubt has raised as to whether this rockfall prevention facility would function properly enough to prevent rockfall efficiently without any damages in case of actual occurrence of rockfall. In addition, it is a reality that in most cases, such work is relied on overseas technology as a whole as the local technical level is low and in case of rockfall prevention net, it is judged that a study on rockfall prevention net that is able to endure more powerful rockfall energy is required as the problem including net bursting is taken place as a result of enough bearing force being failed to be demonstrated due to its partial weak point(not uniformly made). Under this background, in this study, three kinds of model depending on mesh size of expanded metal that is considered to have an adoptability as rockfall prevention net, as target are selected and characteristics depending on mesh size of expanded metal is intended to be researched through a pull-out test performance by using pull-out test equipment rockfall prevention net.

• Journal of Soil and Groundwater Environment
• /
• v.20 no.4
• /
• pp.1-7
• /
• 2015

The degradation of off-flavors which is 2-Methylisoborneol (2-MIB) and geosmin by means of ultrasound (US) and pulsed ultraviolet (PUV) irradiation and its combination with catalyst (wire mesh, wire mesh coated TiO₂, and TiO₂) and additive (H₂O₂) were investigated via water system. A combination treatment of TiO₂ and H₂O₂ heterogeneity with US (24 kHz) and PUV (6000 W) has shown improved results in destroying 2-MIB and geosmin, which may be attributed to chain reactions by the enhanced formation of hydroxyl radicals (·OH) through H₂O₂ dissociation and reactive oxide ions of TiO₂ addition. Rapid degradation of off-flavors occurred within 2 min under PUV process with H₂O₂ 100 mg/L (81.5% for 2- MIB; 79.3% for geosmin) and TiO₂ 100 mg/L (83.7% for 2-MIB; 79.8% for geosmin), while compared with H2O2 100 mg/L (58.4% for 2-MIB; 58.0% for geosmin) and TiO₂ 100 mg/L (59.2% for 2-MIB; 38.5% for geosmin) within 5 min under US process. Surprisingly, the emphasis was given on the comparison with the same injected energies between PUV and US on degradation efficiency. Based on the injected energy comparison, the US provided better degradation performance under equal input power of 200 kJ with H₂O₂ 100 mg/L, while compared with H₂O₂ 100 mg/L under PUV process. Our findings suggest that US can be more effective compared to PUV for the degradation of off-flavors in aspect of energy consumptions.

• Resources Recycling
• /
• v.25 no.3
• /
• pp.29-36
• /
• 2016

The characteristics analysis and pH neutralization test were carried out to use of slurry generated from recycling processes of construction wastes. D (5.0) of raw sludge was $42.4{\mu}m$ and over 60 % of sludge distribute under 45 um (-325 mesh). Muscovite and carbonate minerals were main minerals of fine particles, and the portion of carbonate minerals increased as particle size decreased. Although the more heavy metals were observed in the finer particle size, the contents was found to be less than Korean contaminated soil regulation (area 2). The effects of flocculants addition for accelerating solid-liquid separation were negligible because the slurry already contains excess of coagulant added in the waste concrete recycling process. It was difficult to neutralize the sludge supernatant due to high pH (about 12) by adding acids, but the introduction of $CO_2$ decreased the pH to 8.5, The precipitate recovered during $CO_2$ introduction was determined to be $CaCO_3$ with XRD, and it indicates that high pure $CaCO_3$ could be obtained during the process.

• Journal of the Korea Society of Computer and Information
• /
• v.26 no.4
• /
• pp.119-131
• /
• 2021

In this study, I compared the pattern design method of classic shirts focused on the men's clothing consturction textbook. It was intended to select a shirt pattern drawing method suitable for men in their 20s by conducing a appearance evaluation with a 3D simulation program. Pattern drawing method, sizes, appearance evaluation, garment pressure. were evaluated, and SPSS 26.0 program was used for analysis. According to the Pattern drawing method, there were differences in application sizes, and there were many parts where designated sizes were applied. The shirt pattern is mostly the same for the front chest and back chest, front waist and back waist. However, if there is a front and back difference of the chest and the waist circumference, the fit was considered better. B pattern was evaluated as the best in appearance evaluation, color distribution, and mesh condition through 3D simulation, and B pattern was analyzed as the most suitable method for men in their 20s. Since this study applied the average sizes of the 7th Korean Human Body Dimension Survey report in 20s, it is thought that caution should be paid to apply them to all 20s. In the future, it is also thought that research on the actual fit and patterns of various body types and materials in their 20s should be carried out.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.6
• /
• pp.565-575
• /
• 2022

Thanks to the latest developments in digital architectural technologies, free-form designs that maximize the creativity of architects have rapidly increased. However, there are a lot of difficulties in forming various free-form curved surfaces. In panelizing to produce free forms, the methods of mesh, developable surface, tessellation and subdivision are applied. The process of applying such panelizing methods when producing free-form panels is complex, time-consuming and requires a vast amount of manpower when extracting production data. Therefore, algorithms are needed to quickly and systematically extract production data that are needed for panel production after a free-form building is designed. In this respect, the purpose of this study is to propose mathematical algorithms for the automatic generation of production data of free-form panels in consideration of the building model, performance of production equipment and pattern information. To accomplish this, mathematical algorithms were suggested upon panelizing, and production data for a CNC machine were extracted by mapping as free-form curved surfaces. The study's findings may contribute to improved productivity and reduced cost by realizing the automatic generation of data for production of free-form concrete panels.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.94-105
• /
• 2020

Recently, most studies of 3D printing in construction have focused on the development of 3D printers and materials suitable for construction 3D printers. In comparison, there has been little research on design support tools that enable representative BIM data of building modeling tools to be applied to 3D printing. In addition, existing 3D printing slicing programs are commercialized around manufacturing, showing that they are unsuitable for construction 3D printing. Therefore, this research aims to develop a design support tool for 3D printing for buildings. The developed design support tool was validated based on arbitrary BIM data. Verification showed that wall pattern generation was modeled accurately without errors, and a calculation of the construction period showed that the formula presented in this study was valid. Furthermore, the maximum length of the mesh split was set to 100mm to minimize errors when converting to STL files.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.6 s.73
• /
• pp.819-832
• /
• 2004

This study describes an efficient and facile method for configuration optimum design of structures. One of the ways to achieve numerical shape representation and the selection of design variables is using the design element concept. Using this technique, the number of design variables could be drastically reduced. Isoparametric mapping was utilized to automatically generate the finite element mesh during the optimization process, and this made it possible to easily calculate the derivatives of the coordinates of generated finite element nodes w.r.t. the design variables. For the structural analysis, finite element analysis was adopted in the optimization procedure, and two different techniques(the deterministic method, a modified method of feasible direction; and the stochastic method, a genetic algorithms) were applied to obtain the minimum volumes and section areas for an efficient configuration optimization procedure. Futhermore, spline interpolation was introduced to present a realistic optimum configuration that meet the manufacturing requirements. According to the results of several numerical examples(steel structures), the two techniques suggested in this study simplified the process of configuration optimum design of structures, and yielded improved objective function values with a robust convergence rate. This study's applicability and capability have therefore been demonstrated.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.8 no.2
• /
• pp.10-20
• /
• 2005

The change of stream creation has a very sensitive effect on runoff analysis model using the divergence characteristic of stream. Therefore, in this study, the threshold area of stream creation was examined the change characteristic of topographical parameters. The subject basin of the research was the upper basin of the Kumho water gage station which is located in the middle of the Kumho river. The 1:25,000 numerical geography which was constructed $10{\times}10m$ mesh was used. The range of investigation of topographical parameters are number of stream order, length, area, slope, basin relief, sinuosity ratio, drainage density and total stream length etc. It was found from the result of analysis that the threshold value of 1st order stream has a very big effect on topographical parameters of basin. It was found that the threshold area of stream creation was under $0.10km^2$, the parameters showed a big change but showed a very small change over $0.10km^2$.