• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.6
• /
• pp.272-277
• /
• 2010

The glass-ceramics containing bottom ash (B/A) which was a by-produced from an electrical power plant was fabricated and its crystalline phase, microstructure and mechanical properties were analyzed. At first, the glass was fabricated by adding modifier oxide $Li_2O$ to lower the melting temperature of coal bottom ash. The glass obtained was heat-treated by using a 2-stage process to crystallize, that is to say, to increase the degree of crystallization in the glass-ceramics, the first heat treatment for nucleation was performed followed by the secondary one for the growth of nucleates. The main crystalline phase formed in the glass-ceramics was ${\beta}$-spodumene and the secondary phase was $L_2SiO_3$. It was recognized that the degree of crystallization of glass-ceramics was increased with a holding time of the secondary heat treatment stage. In the case of the specimens hold up to 3 hour, the crystallization was not completed and the microstructures and morphologies of crystalline phase were not uniform. In the specimens of holding time over 9 hours, the cracks were generated inside of it, so its compressive strength would decrease due them. In conclusion, it was able to obtain the optimum condition to fabriate the glass-ceramics having the properties of high crystallization degree, uniform microstructures and morphologies and the high mechanical strength.

• Composites Research
• /
• v.29 no.2
• /
• pp.79-84
• /
• 2016

An adhesive can be used to connect two different materials in structures. In comparing with other connecting methods, such as bolt, rivet, and hot melting, the adhesive does not need to use them. It leads to reduce the weight and decrease the stress concentration along the connecting line. This work studied the comparison of mechanical and interfacial properties of commonly-used two adhesives, acrylic type and bisphenol-A epoxy type. Tensile and flexural strength of neat adhesives were also compared. Lap shear test of two adhesives was deduced from the measurement of tensile and fatigue tests. After testing, the failure patterns of adhesive surfaces were observed by a microscope. Tensile strength and mechanical fatigue resistance at using bisphenol-A epoxy adhesive were better than acrylic adhesive. Also adding CNT reinforcement in epoxy adhesive can anticipate mechanical improvement.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.13 no.2
• /
• pp.51-58
• /
• 2007

This research investigated the effect of different onggi containers (Korean earthenware) on the ripening of kochujang (Korean hot pepper paste). The physical characteristics of 'onggi', were evaluated as function of manufacturing variables such as raw material soils (onggi-specific soil, red brown soil, and fine powdered soil) and galzing treatments. The physical properties were then related to the compositional quality changes of the kochujang fermented at $30^{\circ}C$ for 4 months. The porosity of the onggi containers seems to be increased by the content of finer raw soil rather than the chemical component of soil (amount of CaO, MgO, $K_2O$ and $Na_2O$, acting as melting aid in the firing). Natural glaze was measured to contain higher contents of CaO, MgO, $K_2O$ and $Na_2O$ than the other soils, which is desirable property for the fired onggi. The glazed surface showed higher far-infrared radiation emissivity than the non-glazed part. The kochujang fermented in P0-BG (the glazed onggi from 100 % onggi soil) attained higher concentration of reducing sugar, amino nitrogen and nucleotides compared to those in the other onggis. All of these changes of kochujang in P0-BG resulted in significantly better sensory quality than the other treatments.

• Korean Journal of Food Science and Technology
• /
• v.38 no.3
• /
• pp.385-391
• /
• 2006

Physicochemical properties of hydroxypropylated waxy rice starches were investigated to reduce steeping-time of yukwa (Korean oil-puffed rice snack) processing. Swelling power of hydroxypropylated waxy rice starch increased at relatively higher temperature $(60^{\circ}C)$ than native waxy rice starch $(70^{\circ}C)$. Solubility of hydroxypropylated waxy rice starches increased with increasing propylene oxide content. Pasting temperature $(66.3-66.9^{\circ}C)$ and peak viscosity (216-232 RVU) of hydroxypropylated waxy rice starch were higher than those of native starch (179 RVU) and increased with increasing propylene oxide content. DSC thermal transitions of hydroxypropylated waxy rice starches shifted toward higher temperature. Amylopectin melting enthalpy of hydroxypropylated waxy rice starch (8.4-9.2 J/g) was similar to native starch (9.0 J/g). X-ray diffraction patterns of native and hydroxypropylated waxy rice starches showed typical A-type pattern with no significant differences between them, suggesting hydroxypropylation only affected amorphous region. Results suggest hydroxypropylated waxy rice starch is not applicable for yukwa due to low puffing efficiency and dark color.

• Nuclear Engineering and Technology
• /
• v.8 no.2
• /
• pp.89-99
• /
• 1976

The grafting of acrylic acid in aqueous solution to polyvinyl chloride fibers tab been studied in the presence of ferrous, ferric, and cupric salts, The mutual irradiation technique was adopted using a Co-60 source or a Van do Graaff accelerator. The grafting and homopolymerization were suppressed by the cations. Particularly the grafting was suppressed by the cations in the following order of effectiveness : $Cu^{2+}$>$Fe^{2+}$>$Cu^{3+}$. The rate of grafting (in %/hr) was proportional to the 0.76th power of the dose rate over the range from 8.5f $10^3$ rad/hr to $1.4\times10^5$ rad/dr. The apparent activation energy for the grafting was determined to be 6.1 Kcal/mole between $25^{\circ}$ and $75^{\circ}C$ for the mixture of AA-HaO-$(CH_2Cl)_2$, containing Mohr's salt, $4\times10^{-3}$ mole/l. The increase of the grafting was observed when total dose and dose intensity were raised, or when ethylene dichloride as a swelling agent was saturated in the monomer mixture. The grafted polyvinyl chloride fibers showed considerable improvement in moisture regain, heat shrinkage, and melting properties, but tensile properties were not significantly affected by grafting.

• Design & Manufacturing
• /
• v.14 no.1
• /
• pp.49-55
• /
• 2020

In this study, the fatigue behavior and fatigue life characteristics of PA2200 specimens fabricated by SLS 3D printer were studied. Fatigue tests were performed according to the standard specification (ASTM E468) and fatigue life curves were obtained. In order to perform the fatigue test, mechanical properties were measured according to the test speed of the simple tensile test, and the self-heating temperature of the specimen according to the test speed was measured using an infrared temperature measuring camera in consideration of heat generation due to plastic deformation. There was no significant difference within the set test speed range and the average self-heating temperature was measured at 38.5 ℃. The mechanical strength at the measured temperature showed a relatively small difference from the mechanical strength at room temperature. Fatigue test conditions were established through the preceding experiments, and the loading conditions below the tensile strength at room temperature 23 ℃ were set as the cyclic load. The maximum number of replicates was less than 100,000 cycles, and the fracture behavior of the specimens with the repeated loads showed the characteristics of Racheting. It was confirmed that SLS 3D printing PA2200 material could be applied to the Basquin's S-N diagram for the fatigue life curve of metal materials. SEM images of the fracture surface was obtained to analyze the relationship between the characteristics of the fracture surface and the number of repetitions until failure. Brittle fracture, crazing fracture, grain melting, and porous fracture surface were observed. It was shown that the larger the area of crazing damage, the longer the number of repetitions until fracture.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.497-501
• /
• 1999

The changes of properties were studied for the polypropylene(PP)/Nylon6 blends containing different kinds of compatibilizer made by either reactive extrusion of solution reaction. The compatibilizers were PP grafted with maleic anhydride (MAH) made by reactive extrusion and solution reaction. The grafted MAH contents were 0.3 wt %, and 2.7 wt %, respectively. The composition of the PP/nylon6 blend was fixed at 75/25 by weight. Blending was carried out with twin-screw extruder (L/D=30, ${\psi}=30$) at 300 rpm. As the content of PP-g-MAH was increased, the crystallization peak of Nylon6 decreased gradually then finally disappeared. Disappearance of crystallization peak of Nylon6 was mostly affected by grafted MAH content rather than the preparation method and the amount of compatibilizer. The portion of Nylon6 that could not crystallize in its normal crystallization temperature crystallized together with PP at the crystallization temperature of PP. So called concurrent crystallization was observed. Meanwhile two more peaks were observed during heating cycle. One was exothermic peak at $193^{\circ}C$ near to crystallization temperature of Nylon6, the other was endothermic peak at $215^{\circ}C$ that was $5^{\circ}C$ lower than normal endothermic peak of Nylon6. To analyze the peaks, nylon6 was annealed in the differential scanning calorimeter. As a result, the peak at $193^{\circ}C$ was crystallization peak of imperfect crystalline of Nylon6 and the other peak at $215^{\circ}C$ was melting peak of imperfect crystalline of nylon6.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.28 no.1
• /
• pp.71-78
• /
• 1992

Zr-4 used for a cladding and an end plug of reactor component has creep deformation under operation at high temperature. Creep is regarded as the time dependent deformation of a material under constant applied stress. Although the major source of the deformation of zirconium component in water-cooled reactors is irradiation creep, the thermal creep may give a rise to significant deformation in reactor component especially at relatively high temperatures and at various constant stresses, and therefore it must be predicted accurately. Stress relaxation is the time dependent change of stress at constant strain and it is a process related intimately to creep. In this paper, the creep behavior and stress relaxation of Zr-4 is examined at the temperature of 50$0^{\circ}C$ that is 40% of the absolute melting temperature of Zr-4 under the stress below yield stress and under the various constant strains. The results obtained are summarized as follows: 1) With an increase of stress, the steady state creep rate increases and the creep rupture time decreases. 2) The steady state creep rate $\varepsilon$(%/s) for the stress $\sigma$sub(c) (kgf/mm super(2)) of Zr-4 increases outstandingly. All the empirical equations computed for Zr-4 increases outstandingly. All the empirical equations computed for Zr-4 are in accord with Norton's model equation($\varepsilon$=K$\sigma$ sub(c) super (n)). The constants of materials computed are as follows: K=3.9881$\times$10 super(-5), n=1.9608 3) The rupture time T sub(r) (hr) decreases linearly with the increase of stress on the log-log scaled graph. The empirical equations computed for Zr-4 are in accord with Bailey's model equation (T sub(r)=K sub(1)$\sigma$sub(c) super(m)). The constants of materials computed are as follows: K sub(1)=1.2875$\times$10 super(16), m=-3.467 4) It seems clear that the strain could be quantitatively dependent on the high temperature creep properties such as creep stress, rupture time, steady state creep rate and total creep rate. It is found that these relationships are linear on the log-log graph. 5) In stress relaxation test, as the critical constant strain that can be allowed to the specimen is larger, stress relaxation becomes more rapid, and as the constant strain is smaller, the stress relaxation becomes slower.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.3
• /
• pp.51-57
• /
• 2010

Thermoelectric properties of the p-type $(Bi,Sb)_2Te_3$, hot-pressed with the $(Bi,Sb)_2Te_3$ powders fabricated by melting/grinding method, were characterized with variation of the hot-pressing conditions. Thermoelectric characteristics of the hot-pressed $(Bi,Sb)_2Te_3$ were also analyzed with addition of $ZrO_2$ as nano inclusions. With increasing the hotpressing temperature from $350^{\circ}C$ to $550^{\circ}C$, Seebeck coefficient and electrical resistivity decreased from 275 ${\mu}V$/K to 230 ${\mu}V$/K and 6.68 $m{\Omega}$-cm to 1.86 $m{\Omega}$-cm, respectively. The power factor decreased with addition of $ZrO_2$ nano powders more than 1 vol%, implying that the optimum amount of $ZrO_2$ nano inclusions to get a maximum power factor would be less than 1 vol%.

• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.721-727
• /
• 2002

In order to overcome trade-off among compositions, process and properties of the glasses with high PbO-base composition for PDP Rib, we studied glass crystallization and crystallization kinetics by Differential Thermal Analysis(DTA). Glass powder was obtained through melting/cooling/grinding, with 3 wt%TiO2 addition for the crystal nucleation and growth in $62PbO-19B_2O_3-10SiO_2-9(Al_2O_3-K_2O-BaO-ZnO)$(in wt%) composition glass. This powder was heat-treated for 1 to 10 h at $445^{\circ}C$ for nucleation. DTA measurements were performed to obtain the crystallization peak with $5∼25^{\circ}C/min$ heating rates. DTA crystallization peak temperature increased with increasing the heating rate and decreased with increasing the heating time. Because the Avrami parameter (n) was approximately 1, the surface crystallization occurred. The maximum nucleation time was 2 h.