• 한국수소및신에너지학회논문집
• /
• 제9권2호
• /
• pp.85-92
• /
• 1998

The hydrogenation behavior of $Mg_2Ni$ powder prepared by ball milling has been studied. Ball milled $Mg_2Ni$ was transformed to an amorphous-like state after 200hr ballmilling, and crystallized to $Mg_2NiH_x$ by hydrogenation at got. The hydrogen storage capacity gradually increased as a function of ball milling time. $Mg_2Ni$ by 400hr ballmilling shows higher hydrogen storage capacity (3H/M) than $Mg_2Ni$ by VIM(Vacuum Induction Melting).

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.194-199
• /
• 2000

The creep rate is affected by the temperature and in fact. if the temperature above $T_M/2(T_M:melting\;point)$. The aim of the present investigation is to study the relationship of static creep and cyclic creep behavior of pure copper and the formulation of these phenomena with the special attention to the instantaneous strain. strain rate from time and number of cycles have the same inclination Steady state creep rate depend upon maximum stress and can be expressed as linear function according to Power law creep equations Creep rupture time has relation with creep rate. and it make a group represented as the same direct line regardless of max stress, stress ratio and the temperature. Initial strain effect on continuous creep deformation. and have guantitative relationship between elastic and Plastic strain. LMP have similar tendency than OSDP and MHP according to temperature

• 한국분말재료학회지
• /
• 제1권1호
• /
• pp.15-20
• /
• 1994

The effect of SiC addition on sintering behaviors and microstructures of TiB2 ceramics were studied. The sintering of TiB2 was limited due to the surface diffusion and rapid grain growth at high temperature. However the addition of SiC to TiB2 ceramics improved the densification to above 99% of the theoretical density. The sintering of TiB2-SiC composite starts at 120$0^{\circ}C$ with the melting of the oxides in particle surface as impurities. After the reduction of the oxide by additional cabon at above 140$0^{\circ}C$, the grain boundary diffusion through the interface of TiB2-SiC play an important role. TEM observation showed neither chemical reactions nor other phases formed at the TiB2-SiC interfaces but the microcracks were observed due to the mismatch of thermal expansion between TiB2-SiC.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.205-209
• /
• 2009

Wetting properties between silver-copper-titanium braze alloys with different titanium contents up to 2.8 mass% and hexagonal boron nitride ceramics were investigated using sessile drop method at 1123K in Argon. The final contact angle is less than $30^{\circ}$ when the Ti content was over 0.41 mass%. Meanwhile, the contact angle curves show different behavior. In case of using braze alloy containing 2.8 mass% of titanium, the initial contact angle is acute angle just after the melting of braze. In case of brazes containing titanium less than 2.26 mass%, the contact angle is larger than $90^{\circ}$ at the beginning and slowly decreases to acute angle. The reaction layer of titanium nitride is observed at the interface. In addition, the reaction of Ti in the braze and N in the bulk h-BN seemed to show diffusion limited spreading.

• Journal of Dairy Science and Biotechnology
• /
• 제36권2호
• /
• pp.73-80
• /
• 2018

The textural and rheological properties of cheese are major attributes for the characterization of cheese types, ripening, and consumer preferences. The use of small amplitude oscillatory rheological testing has made it possible for cheese researchers to assess the major properties of cheese, such as melting behavior and storage modulus, without irreversible deformation. In addition, large deformation testing such as textural profile analysis can assess properties such as hardness of cheese. While the sensory properties of cheese are valued by consumers, objective and reliable measurements are paramount for researchers. Ongoing development and refinement of scientific measurement methods of cheese are vital.

• 동굴
• /
• 제76호
• /
• pp.15-17
• /
• 2006

[ $YBa_2Cu_3O_{7-{\delta}}$ ] superconductor films have been prepared on silver substrates by electrophoretic deposition. As silver does not react with $YBa_2Cu_3O_{7-{\delta}}$ compound and has little influence on its superconductivity, it is usually doped in $YBa_2Cu_3O_7$ to improve the strength of the material and eliminate micro cracks. It has been proved that Ag additive can lower the melting temperature of $YBa_2Cu_3O_{7-{\delta}}$ and act as linking bridge among $YBa_2Cu_3O_{7-{\delta}}$ particles, thus in this paper Ag doped $YBa_2Cu_3O_{7-{\delta}}$ thick films are prepared by electrophoretic co deposition. As there are only some referenced experience formula and models for co electrophoretic deposition and does not exist unified explanation, the behavior of Ag particles during co electrophoretic deposition is also studied.

• Bulletin of the Korean Chemical Society
• /
• 제23권8호
• /
• pp.1073-1077
• /
• 2002

Binding of dodecyl trimethylammonium bromide (DTAB) to human and bovine hemoglobin and globin samples has been investigated in 50 mM glycine buffer pH = 10, I = 0.0318 and 300 K by equilibrium dialysis and temperature scanning spectrophotometry techniques and method for calculation of average hydrophobicity. The binding data has been analyzed, in terms of binding capacity concept $({\theta})$, Hill coefficient (nH) and intrinsic Gibbs free energy of binding $({\Delta}Gbv).$ The results of binding data, melting point (Tm) and average hydrophobicity show that human hemoglobin has more structural stability than bovine hemoglobin sample. Moreover the results of binding data analysis represent the systems with two and one sets of binding sites for hemoglobin and globin, respectively. It seems that the destabilization of hemoglobin structure due to removal of heme group, is responsible of such behavior. The results indicating the removal of heme group from hemoglobin caused the depletion of first binding set as an electrostatic site upon interaction with DTAB and exposing the hydrophobic patches for protein.

• Bulletin of the Korean Chemical Society
• /
• 제30권6호
• /
• pp.1337-1340
• /
• 2009

Electrical properties of a fluorinated carbon black (CB)-filled high-density polyethylene (HDPE) polymeric switch were investigated as a function of fluorination pressure at 0.1 ~ 0.4 MPa. From the FT-IR results, the absorption spectra of the fluorinated CB show an absorption band at 1400 ~ 1000 $cm^{-1}\;for\;{\nu}_{C-F}$ and the peak intensity increased with increasing fluorination pressure. Also, the analysis of XPS spectra of the fluorinated CB indicated that fluorine content increased with increasing fluorination pressure. Meanwhile, the surface free energy of the fluorinated CB decreased with increasing fluorination pressure. Consequently, the increase of fluorine contents of CB made a disappearance of negative temperature coefficient (NTC) behavior of the polymeric switch, which was probably due to the reduction of CB reaggregation after melting point of the HDPE, resulted from the decreasing of London dispersive component of the surface free energy for CB particles.

• 한국세라믹학회지
• /
• 제36권5호
• /
• pp.490-496
• /
• 1999

The sintering behavior of LTCC (low temperature cofired ceramics) chip couplers was investigated in relation with Ag diffusion at the interface of glass ceramic substrate-Ag electrode. Sintering temperature was in the range of 825$^{\circ}C$-975$^{\circ}C$. The commercial green sheet and silver electrode were used. Below 875$^{\circ}C$ the diffusion of the Ag ion into the substrate and the penetration of glassy phases into the electrode occurred due to an increase of fluidity. Thus the lectrode line was severely deformed and damaged. At 975$^{\circ}C$ the transformation of crystalline phases into glassy phases and the melting of the Ag electrode resulted in the diffusion of the considerable amount of Ag ions.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.250-253
• /
• 2004

Emphasis has been placed on thin plate fabrication of plain woven carbon fabric reinforced Al matrix composites using liquid pressing process. The composite has potential applications for PDP rear plate. The process is to use the low pressure for infiltration of Al melt into plain woven carbon fabric as the Al melt is pressurized directly. The minimum pressure required for the infiltration was calculated from force balance equation, permeability measurements and compaction behavior of carbon fiber. Also, the melting temperature and the holding time have been optimized. In order to measure coefficient of thermal expansion (CTE) of the composites, the thermal strain measurement using strain gage was performed and the thermal conductivity of the composites was measured using laser flash method. The constituent materials of the composite are PAN type carbon fibers as reinforcements and 6061 Al alloys as matrices.