• Journal of Technologic Dentistry
• /
• v.26 no.1
• /
• pp.41-48
• /
• 2004

Ti-20%Zr(-5%Cr) alloys not containing harmful Al and V were newly designed in order to reveal their possibility for dental casting and melted in an arc melting and casting furnace under Ar atmosphere. The corrosion resistance was studied by anodic polarization test. From the observation of anodic polarization behavior, it was found that the corrosion resistance was markedly increased by the addition of Cr. The corrosion resistance of Ti-20%Zr-5%Cr alloy was superior to that in Ti-6%Al-4%V alloy but almost similar to that in CP Ti using in market place today.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.72-75
• /
• 2003

HTS tubes were fabricated in terms of various SrSO4 additions by Centrifugal Forming Method. For powder melting by induction, the optimum temperature ranges of melting and preheating were 105$0^{\circ}C$~110$0^{\circ}C$ and 55$0^{\circ}C$ for 30min respectively The mould rotating speed was 1000rpm. A tube was annealed at 84 $0^{\circ}C$ for 72 hours in oxygen atmosphere. The plates like grains more than 20${\mu}{\textrm}{m}$ were well developed along the rotating direction of mould regardless of the amounts of SrSO4 in Bi2212. The measured Ic and Jc at 77K(B = 0T) in Bi2212 with 7％ SrSO4 composition were about 680A and 380A/$\textrm{cm}^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.527-530
• /
• 2004

High-temperature Superconductor(HTS) tubes were fabricated in term of different diameter, length and thickness by centrigugal forming method. For powder melting by induction the optimum range of melting temperatures and preheating temperature were $1050^{\circ}C{\sim}1100^{\circ}C\;amd\;550^{\circ}C$ for 30min, respectively. The mould renting speed was 1000rpm. A tube was annealed at $840^{\circ}C$ for 72hours in oxygen atmosphere. The plate-like grains were well developed along the renting direction and typical grain size was about more than $40{\mu}m$. It was found that Ic values increased with increasing the tube diameter while the Ic decreased with increasing tube thickness. Also Ic decreased with increasing the tube length. The measured Ic in $50mm{\times}70mm{\times}25mm$ tube was about 896Amp.

• Journal of Korea Foundry Society
• /
• v.27 no.3
• /
• pp.131-134
• /
• 2007

[ $SF_6$ ] gas that is used as a protective cover gas for Mg and Mg alloys during melting and casting has extremely high greenhouse effect. CaO added Mg alloys could maintain their original mechanical properties and original abilities such as fluidity and hot tearing susceptibility. The ignition temperature increased with increasing CaO addition under ambient atmosphere and nitrogen atmosphere. The minimum amount of $SF_6$ gas decreased by 0.13 wt%CaO added AZ91D Mg alloy in the sealed condition.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.4
• /
• pp.360-364
• /
• 1999

The growth of crystals with high melting point$t_{fus}$$\geq$$1600^{\circ}C$ faces the researcher with experimental problems, as the choice of materials that withstand such high t is rather limited. Many metallic construction materials are in this high t range already molten or exhibit at least a drastically reduced mechanical strength. The very few materials with$t_{fus}$$1600^{\circ}C$ as e.g. W, Mo, and partially even Ir are more or less sensitive against oxygen upon heating. Whenever possible, high t crystal growth is performed under inert atmosphere (noble gases). Unfortunately, many oxides are not thermodynamically stable under such conditions, as reduction takes place within such atmosphere. A thoroughly search for suitable growth conditions has to be performed, that are on the one side "oxidative enough" to keep the oxides stable and on the other side "reductive enough" to avoid destruction of constructive parts of the crystal growth assembly. The relevant parameters are t and the oxygen partial pressure${po}_{2}$. The paper discusses quantitatively relevant properties of interesting oxides and construction materials and wasy to forecast theri behavior under growth conditions.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1999.06a
• /
• pp.51-67
• /
• 1999

The growth of crystals with high melting points tfus$\geq$1$600^{\circ}C$ faces the researcher with experimental problems, as the choice of materials that withstand such high t is rather limited. Many metallic construction materials are in this high t range already molten or exhibit at least a drastically reduced mechanical strength. The very few materials with tfus》1$600^{\circ}C$ as e.g. W, Mo, and partially even Ir are more or less sensitive against oxygen upon heating. Whenever possible, high t crystal growth is performed under inert atmosphere (noble gases). Unfortunately, any oxides are not thermodynamically stable under such conditions, as reduction takes place within such atmosphere. A thoroughly search for suitable growth conditions has to be performed, that are on the one side "oxidative enough" to keep the oxides stable and on the other side "reductive enough" to avoid destruction of constructive parts of the crystal growth assembly. The relevant parameters are t and the oxygen partial pressure pO2. The paper discusses quantitatively relevant properties of interesting oxides and construction materials and ways to forecast their behavior under growth conditions.r growth conditions.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.189-192
• /
• 2012

Manufacturing process for silicate glass phosphors containing Eu2+ activator and their photoluminescence property have been studied. We adopted powder sintering process instead of traditional glass melting process for making glass phosphor. At first, phosphor powders were synthesized at 1200 ℃ for 2-3 hours under a reducing atmosphere with 10% H2-90% N2 gas mixture. The reduced powders were compacted into discs and then the discs weresintered at 1400 ~ 1500 ℃ for 1 hr under a reducing atmosphere of 5H2-95% N2. The enhancement of PL intensity by Al2O3 addition, XPS binding energy shift of Si 2p and O 1s, sintering shrinkage, and crystallization were characterized.

• Journal of the Korean Ceramic Society
• /
• v.18 no.4
• /
• pp.247-256
• /
• 1981

Silica bricks had been in arc-furnace roofs of various sizes and steelmaking practices. The resulting materials were examined with reference to mineral and chemical changes. Silica bricks develope definite zones while in service. These zones represent a concentration gradient through the brick that results from the thermal gradient across the brick and from the furnace atmosphere. There are major brick losses by spalling as well as by melting of the hot-face surface in an iron-oxide rich liquid.

• Journal of the Korean Magnetic Resonance Society
• /
• v.6 no.2
• /
• pp.113-117
• /
• 2002

The chalcogenide glass (ALS, $Al_2S_3-La_2S_3$) was prepared by melting a stoichiometric mixture of aluminum powder and $La_2S_3$ under $H_2S$ atmosphere at $1200{\circ}C$. Glasses containing 0.1-0.1% of $Mn^{2+},\;Gd^{3+}$ and $Cu^{2+}$ were also prepared. The characteristic features of the ESR spectra for the transition metal containing ALS glasses are interpreted.

• Journal of the Korean Ceramic Society
• /
• v.21 no.3
• /
• pp.231-238
• /
• 1984

Heavy metal fluoride glasses exhibit considerable promise as high transparency materials from the UV to the IR. These glasses are prepared by fusion of the mixture of metal fulorides($ZrF_4$, $BaF_2$, $LaF_3$ etc) at 800-1, 00$0^{\circ}C$ under the inert$(N_2)$ or reactive ($CCl_4$, $Cl_2$) atmosphere following the casting into glass on cooling. Infrared absorption at the 3, 400 cm-1 -OH peak has been measured as a function of thickness for several ZrF-$BaF_2$-LaF and $HfF_4$-$BaF_2$-$LaF_3$ glasses to separate contributions from bulk and surface -OH. For glasses melted under $CCl_4$ reactive atmosphere the peak is due almost entirely to surface-OH. and melting in a closed reactor was best for removing -OH. In ambient atmosphere the -OH peak exhibited no time dependence over a 30 d period indicating a very small rate of surface attack by atmospheric H2O. Removal of -OH absorption processing was generally easier and more complete for the $BaF_2$/ThF4-glasses than for the $ZrF_4$-or $HfF_4$-based glasses.