• International Journal of Highway Engineering
• /
• v.18 no.3
• /
• pp.59-65
• /
• 2016

PURPOSES : This paper aims to develop a road pavement de-icing system using carbon sheet to replace the older snow de-icing method. Carbon sheet is a light and high-strength metal. Hence, various bodies of research for its applications in many industries have progressed. METHODS : The experiment was conducted in a laboratory. The carbon sheet supplied voltage through a power supply system, and produced heat transfers to the concrete surface. Various factors, such as pavement material, carbon sheet width, penetration depth, and freezing-thawing resistance, were considered in the conducted experiments to confirm the heating transfer efficiency of the carbon sheet. RESULTS : The carbon sheet used was a conductor. Therefore, it produced heat if voltage was supplied. The exposed carbon sheet on the atmosphere did not affect the carbon sheet width when it provided constant voltage. However, the sheet showed different heating behaviors by width change when the carbon sheet penetrated into the concrete. Moreover, the freezing-thawing resistance was decreased by the carbon sheet with increasing width. CONCLUSIONS : The experiments confirmed the possibility of developing a road snow melting system using a carbon sheet. The antiicing system using the carbon sheet to replace the traditional anti-icing system has disadvantages of environmental pollution risk and electric leakage. The pavement also improved its toughness resistance. The utilization value will be very high in the future if carbon sheet heat loss can be minimized and durability is improved.

• Journal of Korea Foundry Society
• /
• v.8 no.3
• /
• pp.287-295
• /
• 1988

The experiment was carried out for the purpose of studying the carburization of pure iron ingot and sintered iron powder by solid carbon in the atmosphere of CO gas. The volocity of carburization was estimaed by the diffusion coefficient D calculated by carburization equation. The results obtained were as follow: 1. The higher the carburization temperature, carburization depth and carbon concentration were increased, and the melting zone which had $2.8{\sim}3.4%C$ at the $3{\sim}4mm$ from interface of carburization was formed at $1300^{\circ}C$. 2. The main carburization mechanism of pure iron ingot and the sintered iron powder were proceeded by CO gas up to $1100^{\circ}C$, solid carbon over than $1300^{\circ}C$, respectively. 3. The main carburization mechanism of pure iron ingot at $1200^{\circ}C$ was proceeded by solid carbon, and sintered iron powder was proceeded bs CO gas, however, in case the reaction time, the carburization was proceeded by solid carbon over than 5hrs. 4. The diffusion coefficient D of carbon were $0.559{\times}10^{-6}cm^2.sec^{-1}$ at $1100^{\circ}C$, $0.237{\times}10^{-6}cm^2.sec^{-1}$ at $1200^{\circ}C$, $0.087{\times}10^{-6}cm^2.sec^{-1}$ at $1300^{\circ}C$, in case of pure iron ingot carburized. 5. The diffusion coefficient D of carbon were $0.124\;cm^2.sec^{-1}$ at $1100^{\circ}C$, $0.102\;cm^2.sec^{-1}$ at $1200^{\circ}C$, $0.480\;{\times}10^{-6}cm^2.sec^{-1}$ at $1300^{\circ}C$, in the case of sintered iron carburized at the pressuring $4ton\;/\;cm^2$.

• Resources Recycling
• /
• v.27 no.5
• /
• pp.30-37
• /
• 2018

For recylcing of high purity tantalum (Ta) scrap, We investigated manufacture of tantalum powder using hydride-dehydride (HDH) process. Tantalum had excellent properties such as ductile, hardness and high melting point. Usually these properties made difficult to make a powder. In this study, Tantalum powder was manufactured using Tantalum hydride via hydridation. Tantalum hydride was formed at $500^{\circ}C$, 5 hr/$700^{\circ}C$, 3 hr and it is easy to make a tantalum hydride powder because hydrogen in the tantalum act as a defect dislocation and lattice expansion. The powder was pulverized to a size of less than $10{\mu}m$ under a condition of 1300 rpm, 30 min using a ring mill, and tantalum powder with less than 50 ppm hydrogen was prepared through dehydridation in an Ar and low vacuum atmosphere.

• Journal of the Korean earth science society
• /
• v.41 no.1
• /
• pp.1-18
• /
• 2020

This study presented the effects of the assumed mass-size relationship for snow on the simulated surface precipitation by using cloud microphysics parameterizations in Weather Research and Forecasting (WRF) model. The selected cloud microphysics parameterizations are WRF Double-Moment 6-class (WDM6) and WRF Single-Moment 6-class (WSM6) in the WRF model. We replaced the mass-size relationship for snow in WDM6 and WSM6 with Thompson's mass-size relationship retrieved from measurement data. The sensitivity of the modified WDM6 and WSM6 was tested for the idealized 2-dimensional squall line and winter precipitation system over the Korean peninsula, respectively. The modified WDM6 and WSM6 resulted in the increase of graupel/rain mixing ratios and the decrease of snow mixing ratio in the low atmosphere. The changes of hydrometeor mixing ratio and surface precipitation could be due to the collision-coalescence process between raindrops and snow and the graupel melting process.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.1
• /
• pp.28-33
• /
• 2017

SiC fiber can be used up to $1800^{\circ}C$ in both inert and air atmosphere without any problems such as melting and oxidation. SiC fibers can be applied to dust filtering processes as a bag filter at a high temperature above $700^{\circ}C$, which is far beyond the temperature range of currently available industrial bag filter. However the studies for the degradation of SiC fibers were still lacked in the harsh environment of steel industries and thermoelectric power plants. In this study, SiC fibers were reacted with steel dust and thermal power plant dust at a high temperature of $500^{\circ}C$ or higher, and the degraded shape of the fiber surface was observed by SEM. Also the degree of oxygen diffusion on the surface and inside of SiC fiber was analyzed by EDS.

• International Journal of Safety
• /
• v.4 no.1
• /
• pp.14-17
• /
• 2005

Recycled polyol was obtained by glycolysis of MDI-based Polyurethane(PU) rigid foam. The chemical structure of the recycled pclyol was confirmed by GC(gas chromatography) and 1H-NMR. The recycled polyol throughout the glycolysis contained liquid polyol and methylenedianiline(MDA). MDA which could cause liver cancer is carcinogenic material. TWA(Time Weighted Average.) amount for MDA in MSDS(Material Safety Data Sheets) was confined less than 0.1 ppm. The melting temperature of MDA is $92^{\circ}C$, and boiling temperature is $398^{\circ}C$. During the gylcolysis most of MDA was dissolved in liquid polyol. The probability that MDA diffuses into the atmosphere is low but there could be an absorption of MDA into skin. Furthermore because MDA is amine compound, recycled polyol which contained MDA had a difficulty in reaction control of polyurethane. Therefore reduction of MDA amount was needed strongly. In this study the elimination of MDA were performed through deamination of the recycled polyol by glycidyl ether compounds. As glycolysis was proceeded, the amount of MDA was 9.8 wt % at early stage and increased up to 14.0 wt % after 8 hours reaction. It was found that 2-Ethylhexyl glycidyl ether which contains aliphatic moiety was very effective compound for eliminating the primary aromatic amine compound :md the optimal mole ratio of 2-ethylhexyl glycidyl ether to MAD was 3. The final polyol after deamination by 2-ethylhexyl glycidyl ether has an appropriate viscosity(less than 500 centi poise) for polyurethane reaction.

• Journal of Korea Foundry Society
• /
• v.18 no.4
• /
• pp.383-388
• /
• 1998

Effects of $CaCN_2$ addition on the grain refinement in the AM60 magnesium ingots were investigated. The effects of the $CaCN_2$ are estimated with different inoculation temperatures, inoculation contents, and holding time to find out the optimum condition. AM60 alloy was melted in the low carbon steel crucible by cylindrical electric furnace under an argon atmosphere. The melting and casting apparatus is specially designed for magnesium alloys. The grain size of AM60 magnesium alloy decreased significantly with an increase in $CaCN_2$ content and, at 0.8 wt% $CaCN_2$ or more, grain size becomes constant at about $85 {\mu}m$. The optimum condition was obtained in the 0.8 wt% $CaCN_2$ for holding molten metal of 30 min. at the temperature of $710^{\circ}C$. The tensile properties of AM60 magnesium alloys were improved due to grain refinement by addition of $CaCN_2$. In the optimum condition, the yield strength, tensile strength and elongation were ${\sigma}_{0.2}=107 MPa$, ${\sigma}_{T.S}=234 MPa$ and e=14.2%. The variation of stress with strain obeyed the relationship of the ${\sigma}=K{\varepsilon}^n$. The strain-hardening exponent, n and strength coefficient, K obtained in the 0.8 wt% $CaCN_2$ added AM 60 magnesium alloy were n=0.21 and K=390 MPa.

• Atmosphere
• /
• v.23 no.3
• /
• pp.265-273
• /
• 2013

To investigate properties of cloud and rainfall occurred at Boseong on 10 July 2012, Raindrop Size distributions (RSDs) and other parameters were analyzed using observation data collected by Micro Rain Radar (MRR) and PARticle SIze and VELocity (PARSIVEL) disdrometer located in the National center for intensive observation of severe weather at Boseong in the southwest of the Korean peninsula. In addition, time series of RSD parameters, relationship between reflectivity-rain rate, and vertical variation of rain rates-fall velocities below melting layer were examined. As a result, good agreements were found in the reflectivity-rain rate time series as well as their power relationships between MRR and PARSIVEL disdrometer. The rain rate was proportional to reflectivity, mean diameter, and inversely proportional to shape (${\mu}$), slope (${\Lambda}$), intercept ($N_0$) parameter of RSD. In comparison of the RSD, as rain rate was increased, the slope of RSD became less steep and the mean diameter became larger. Also, it was verified that reflectivities are classified in three categories (Category 1: Z (reflectivity) > 40 dBZ, Category 2: 30 dBZ < Z < 40 dBZ, Category 3: Z < 30 dBZ). As reflectivity was increased, rain rate was intensified and larger raindrops were existed, while reflectivity was decreased, shape (${\mu}$), slope (${\Lambda}$), intercept ($N_0$) parameter of RSD were increased. We expected that these results will lead to better understanding of microphysical process in convective rainfall system occurred during short-term period over Korean peninsula.

• Journal of Powder Materials
• /
• v.22 no.4
• /
• pp.266-270
• /
• 2015

The synthesis of NiTi alloy powders by hydrogen reduction and dehydrogenation process of NiO and $TiH_2$ powder mixtures is investigated. Mixtures of NiO and $TiH_2$ powders are prepared by simple mixing for 1 h or ball milling for 24 h. Simple-mixed mixture shows that fine NiO particles are homogeneously coated on the surface of $TiH_2$ powders, whereas ball milled one exhibits the morphology with mixing of fine NiO and $TiH_2$ particles. Thermogravimetric analysis in hydrogen atmosphere reveals that the NiO and $TiH_2$ phase are changed to metallic Ni and Ti in the temperature range of 260 to $290^{\circ}C$ and 553 to $639^{\circ}C$, respectively. In the simple-mixed powders by heat-up to $700^{\circ}C$, agglomerates with solid particles and solidified liquid phase are observed, and the size of agglomerates is increased at $1000^{\circ}C$. From the XRD analysis, the presence of liquid phase is explained by the formation and melting of $NiTi_2$ inter-metallic compound due to an exothermic reaction between Ni and Ti. The simple-mixed powders, heated to $1000^{\circ}C$, lead to the formation of NiTi phase but additional Ni-, Ti-rich and Ti-oxide phases. In contrast, the microstructure of ball-milled powders is characterized by the neck-grown particles, forming $Ni_3Ti$, Ti-oxide and unreacted Ni phase.

• Korean Journal of Materials Research
• /
• v.22 no.5
• /
• pp.243-248
• /
• 2012

ZrN nanoparticles were prepared by an exothermic reduction of $ZrCl_4$ with $NaN_3$ in the presence of NaCl flux in a nitrogen atmosphere. Using a solid-state combustion approach, we have demonstrated that the zirconium nitride nanoparticles synthesis process can be completed in only several minutes compared with a few hours for previous synthesis approaches. The chemistry of the combustion process is not complex and is based on a metathesis reaction between $ZrCl_4$ and $NaN_3$. Because of the low melting and boiling points of the raw materials it was possible to synthesize the ZrN phase at low combustion temperatures. It was shown that the combustion temperature and the size of the particles can be readily controlled by tuning the concentration of the NaCl flux. The results show that an increase in the NaCl concentration (from 2 to 13 M) results in a temperature decrease from 1280 to $750^{\circ}C$. ZrN nanoparticles have a high surface area (50-70 $m^2/g$), narrow pore size distribution, and nano-particle size between 10 and 30 nm. The activation energy, which can be extracted from the experimental combustion temperature data, is: E = 20 kcal/mol. The method reported here is self-sustaining, rapid, and can be scaled up for a large scale production of a transition metal nitride nanoparticle system (TiN, TaN, HfN, etc.) with suitable halide salts and alkali metal azide.