• Journal of Welding and Joining
• /
• 제33권4호
• /
• pp.17-23
• /
• 2015

Laser-gas metal arc hybrid welding has been considered as an alternative process of gas metal arc welding for offshore pipe laying. Fiber delivered high power lasers which enable deep penetration welding were recently developed but high power welding characteristics were not fully understood yet. In this study, the influence of shielding gas composition on welding phenomena in high power laser welding was investigated. Bead shapes, melt ejection and dropping were observed after autogenous laser welding with 100% Ar, Ar-20% $CO_2$, Ar-50% $CO_2$, and 100% $CO_2$ shielding gas. Process parameter window was widest with Ar-50% $CO_2$ shielding gas and the penetration was deepest with 100% $CO_2$ shielding gas. The melt dropping was not observed when Ar-50% $CO_2$ or 100% $CO_2$ shielding gas was supplied.

• Journal of Welding and Joining
• /
• 제26권2호
• /
• pp.92-97
• /
• 2008

In welding of thin plate, some defects such as melt through and unmelted zone occur easily at welding start, however there is a limited study on those problems. Therefore the effects of start block and arc length on melt through and unmelted zone at start were investigated in this study. When start block height was lower than base metal, there was melt through at start. And when the height was even with base metal, no unmelted zone existed. Unmelted zone was increased as start block height increased from 0mm to 0.5mm. However unmelted zone was not much changed as the height increasing from 0.5mm to 1.0mm. When gap existed between start block and base metal, melt through occurred. However, unmelted zone was increased as the contact force of start block on base metal was increased from 0kgf to 7.5kgf. And when arc length was decreased from 3.8mm to 3.0mm, unmelted zone was decreased. It was concluded that the optimum condition to prevent melt through and to minimize unmelted zone would be with start block height 0.25mm, contact force 3.0kgf, and arc length 3.4mm. This optimum condition was applied to the mass production line and resulted in satisfied outcome.

• 한국생산제조학회지
• /
• 제6권3호
• /
• pp.73-81
• /
• 1997

This study was to find the best adhesive condition comparing mechanical property in case of hot-melt adhesion using glue-gun, ultrasonic welding with adhesion and only ultrasonic welding in order to adhere thermoplastic resin of polyethylene (PE) in which reliable adhesion was resulted in case of ultrasonic welding with same materials of PE. The best welding condition were acquired at welding time 1 second, welding pressure 250kPa for PE-PE where welding time and welding pressure were increased in accordance with the increase of material strength. At the best ultrasonic welding conditions, bonding strength of PE-PE welding was about 21MPa of which material have tensile strength of 24MPa. Through the analysis of microscophic test for ultrasonic welding structure, it was distinguished between well welded structure with higher intermolecule flow and bad welded structure with lower flow, of which result is mostly correspond with the result of tensile strength test.

• 해양환경안전학회지
• /
• 제3권2호
• /
• pp.23-31
• /
• 1997

The results of high speed photography, acoustic emission detection and plasma UV radiation intensity measurement during CO2 laser welding of stainless steel 304 are presented. Video images with high spatial and temporal resolution allowed to observe the melt dynamics and keyhole evolution. The existence of a high speed melt flow which originated from the part of weld pool and flowed along the sides wall of keyhole was confirmed by the slag motion on the weld pool. the characteristic frequencies of flow instability and keyhole fluctuations at different welding speed were measured and compared with the results of Fourier analyses of temporal acoustic emission (AE) and light emission (LE) spectra. The experimental results were compared with the newly developed numerical model of keyhole dynamics. (The model is based on the assumption that the propagation of front part of keyhole into material is due to the melt ejection driven by laser induced surface evaporation.) The calculations predict that a high speed melt flow is induced at the front part of keyhole when the sample travel speed exceeds several 10mm/s. The numerical analysis also shows the hump formation on the front keyhole wall surface. Experimentally observed melt behavior and transformation of the AE and LE spectra with variation of welding speed are qualitatively in good agreement with the model predictions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권3호
• /
• pp.282-292
• /
• 2007

The present paper describes the results of high speed photography, acoustic emission (AE) detection and plasma light emission (LE) measurement during $CO_2$ laser welding of 304 stainless steel in different processing conditions. Video images with high spatial and temporal resolution allowed to observe the melt dynamics and keyhole evolution. The existence of keyhole was confirmed by the slag motion on the weld pool. The characteristic frequencies of flow instability and keyhole fluctuations at different welding speed were measured and compared with the results of Fourier analyses of temporal AE and LE spectra. The experimental results were compared with the newly developed numerical model of keyhole dynamics. The model is based on the assumption that the propagation of front part of keyhole into material is due to the melt ejection driven by laser induced surface evaporation. The calculations predict that a high speed melt flow is induced at the front part of keyhole when the sample travel speed exceeds several 10 mm/s. The numerical analysis also shows the hump formation on the front keyhole wall surface. Experimentally observed melt behavior and transformation of the AE and LE spectra with variation of welding speed are qualitatively in good agreement with the model predictions.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.88-90
• /
• 2007

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권3호
• /
• pp.68-77
• /
• 1994

TIG welding process is applied for the active metal such as aluminum and titanium, also sometimes for overlay welding of superalloy. However the welding speed to be applied is very low because of the unstable bead formed in the region of high current and high welding speed. The present study was carried out to examine the basic phenomena of high speed TIG melt run welding by the 2% Th - W electrode(dia.3.2mm) of various tip shapes.

• Korean Chemical Engineering Research
• /
• 제55권4호
• /
• pp.561-566
• /
• 2017

폴리머 재질의 관을 융착 시키기 위해서는 버트 융착 공정을 거치는데, 최근 융착면에 굴곡을 주어 융착 강도를 높이고자 하는 시도가 있었다. 본 연구에서는 융착면의 굴곡이 폴리머의 열유체 거동 및 융착 강도에 어떠한 영향을 미칠 것인지 2차원 축대칭 평면에서 유한요소법을 사용하여 살펴보았으며, 고밀도폴리에틸렌 관을 대상으로 하였다. 열유화 단계에서 융착면의 형상을 따라 굴곡진 상경계면이 나타남을 확인할 수 있었다. 접합 단계에서는 굴곡진 상경계면과 융착면 사이에서의 멜트의 압착 흐름이 나타남을 확인할 수 있었으며, 굴곡융착부의 낮은 전단율은 관의 축과 수직 방향 배향을 완화시켜 융착부 강도 향상에 도움을 줄 수 있을 것으로 예상된다.

• Journal of Welding and Joining
• /
• 제13권3호
• /
• pp.46-54
• /
• 1995

The structural changes of Al-Cr alloys due to the difference in the growth rates were investigated in the study using the water cooled copper chill apparatus, the levitation apparatus, and the melt spinner. Growth rate was evaluated by means of thermal analysis could measured the cooling rate up to 10$^{5}$ K/sec. The transformation from the cell structure to the massive transformed structure was obtained the Al-3.43wt%Cr alloy in the melt spinner method.

• Journal of Welding and Joining
• /
• 제1권2호
• /
• pp.76-82
• /
• 1983

The chemical composition of deposit metal by flux cored arc welding can be easily regulated though addition of deoxidizers and alloying elements in cored flux and fluxes of flux coored wire arc analogous to those of coated electrode. It is necessary to investigate the transfer and yield efficiency due to addition of necessary alloy elements in deposit metal. This report is made to intorduce an experimental equation from the relation between welding condition and extent of penetration, deposit metal and weld melt slag and to estimate transfer and yield efficiency of alloy components in fluxes through chemical analysis of deposit metal.