• Elastomers and Composites
• /
• v.48 no.1
• /
• pp.18-23
• /
• 2013

Nylon 12 elastomer was slightly crosslinked in molten state by the addition of small amount of dicumyl peroxide (DCP) as a crosslink agent and triallycyanuate (TAC) as a co-agent during melt compounding at $160^{\circ}C$ in an internal mixer. The effect of the peroxide crosslinking on mechanical, dynamic mechanical and rheological properties of the nylon 12 elastomer was investigated by means of tensile testing, dynamic mechanical analysis (DMA) and small amplitude oscillating rheometer, respectively. With modification, there is an improvement in tensile modulus and Young's modulus with decease in elongation at break. DMA results for peroxide modified nylon 12 elastomers demonstrated that the glass transiaiton temperature of PTMG segment shifted to higher temperature and the storage modulus remained constant above the melting temperature of nylon 12 segments. Melt rheological studies revealed that the peroxide modified nylon 12 elastomer exhibited a more solid like behavior and stronger shear thinning behavior compared to neat nylon 12 elastomer, which was more prominent at higher TAC content in the polymer matrix. The peroxide modified nylon 12 elastomer exhibited good elastic recoverability and improved mechanical properties without sacrificing melt processibilty, and especially the service temperature range increased as compared to neat nylon 12 elastomer.

• Polymer(Korea)
• /
• v.35 no.4
• /
• pp.356-362
• /
• 2011

The branched polycarbonates (B-PCs) with two different branching agents were synthesized from melt polymerization. The contents of branching agent were in the range of 0.001~0.005 mol%. The chemical structure of the synthesized PC was determined by FTIR, $^1H$ NMR, and $^{13}C$ NMR, spectroscopy. The molecular weight, glass transition and degradation temperatures were determined by GPC, DSC, and TGA. The molecular weight of the phloro type B-PC had a lower value than the other one, and the glass transition temperature increased with molecular weight. Compared with linear PC, the rheological properties of the B-PC indicated an increase of complex viscosity in the low frequency region and shear thinning tendency. Power law index(n) representing shear thinning was calculated by linear regression and the values were in the range of 0.483~0.996. The rheological properties of the B-PCs were measured by a dynamic rheometer.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.166-169
• /
• 2004

Permalloys were successfully fabricated by melt drag casting in the present study, and their variation of microstructure and consequent magnetic properties were investigated as a function of Si contents and annealing temperature. The increases in Si content and annealing temperature resulted in the increases of grain size and amount of $FeNi_3$ ordered phase. Both the grain size and $FeNi_3$ ordered phase controlled by Si and annealing temperature had a important role on permeability of permalloys.

• Journal of Mechanical Science and Technology
• /
• v.14 no.2
• /
• pp.177-187
• /
• 2000

Dilution is an important factor which influences the properties of clad layer. In this paper the change of dilution during laser cladding and the control of dilution are simulated by a finite element method. The adaptive mesh method is adopted for the time-dependent finite element method computation so that the shape of melt pool can be well represented. The situation of the width control of melt pool is also simulated, which indicates that the dilution can be controlled if the width of melt pool is controlled. Computational results indicate that if a line energy (input energy per unit distance) remains constant the dilution will increase with time, especially at the beginning. Simulation results show that it is possible to control dilution in a certain range if the line energy decreases with time. Experiment of Nd: YAG laser cladding with wire feeding is performed. Experiment results coincide well with the FEM results.

• Progress in Superconductivity
• /
• v.2 no.1
• /
• pp.15-19
• /
• 2000

[ $YBa_2Cu_3O_{7-\delta}$ ] thin films were deposited by laser ablation using modified melt-textured grown targets. As the laser energy density was increased, the films showed an increasing c-axis orientation and an improvement of superconducting properties. However, at 4 $J/cm^2$, the degree of c-axis alignment and $J_c$ of the film were considerably reduced. These were attributed to the enhanced a-axis outgrowths. It was shown that the increased laser energy density resulted in the formation of $Y_2O_3$ inclusions during the c-axis film growth, and that these inclusions nucleated the a-axis outgrowths.

• Journal of the Korean Ceramic Society
• /
• v.27 no.4
• /
• pp.567-573
• /
• 1990

Solidification condition for preparing transparent ${\gamma}$-6Bi2O3.GeO2 polycrystals by unidirectional solidification of melt, were investigaetd and the properties of the polycrystals prepared were measured. The ${\gamma}$-6Bi2O3.GeO2 polycrystals showing transparency like a single crystal were obtained by the unidirectional solidification of ${\gamma}$-6Bi2O3.GeO2 melt at a solidification rate of 0.5mm/h under a thermal gradient of 12$0^{\circ}C$/cm. The transparent polycrystals obtained showed the same photoconduction and optical activity as the ${\gamma}$-6Bi2O3.GeO2 single crystals grown by Czochralski method. But the electro-optic effect of polycrystals was heterogeneous because the colummar ${\gamma}$-6Bi2O3.GeO2 crystals were not oriented to the particular crystallographic direction.

• Korea-Australia Rheology Journal
• /
• v.19 no.3
• /
• pp.133-139
• /
• 2007

Low density polyethylene nanocomposites were prepared by melt intercalating maleic anhydride grafted polyethylene and montmorillonite clay. It has been found that maleic anhydride has promoted strong interactions between polyethylene and montmorillonite, leading to the homogeneous dispersion of clay layers. Rheological experiments revealed that prepared nanocomposites exhibited shear thinning behaviour. Polyethylene nanocomposites exhibited an increase in steady shear viscosities compared to virgin polyethylene owing to strong polymer clay interactions. The tensile strength of nanocomposites was improved but elongation at break decreased considerably. Also, barrier properties improved significantly with montmorillonite content.

• Electrical & Electronic Materials
• /
• v.10 no.10
• /
• pp.995-999
• /
• 1997

For melt-spun Fe-Nd-C alloy variation of phase development and magnetic properties with the variety of small Al addition was investigated. As the amount of Al addition increased the amorphization of Fe$_{14}$/Nd$_{2}$/C or $\alpha$-Fe was retarded and the residual Fe$_{14}$/Nd$_{2}$/C or $\alpha$-Fe did not eliminated after heat treatment resulting in poor coercivities of the ribbons. The grain size of Fe$_{14}$/Nd$_{2}$/C increased with the increase of Al addition and the abnormal grain was often found out in the ribbon heat treated for more then 10 min. The enhancement of coercivity was the highest with the addition of 0.5at%Al. As the amount of Al addition increase the coercivities dropped rapidly. The highest coercivity obtained so far is 13.9kOe which about 16% higher than that(11.2kOe) obtained from the Al-free specimen.

• Journal of Powder Materials
• /
• v.5 no.1
• /
• pp.50-56
• /
• 1998

A new process using rapid solidification (melt spinning method) followed by pressing and sintering was investigated to produce the n-type thermoelectric ribbons of 90% $Bi_2Te_3$+10% $Bi_2Se_3$ doped with $CdCl_2$. Quenched ribbons are very brittle and consisted of homogeneous $Bi_2Te_3-Bi_2Se_3$ pseudo-binary solid solutions. Property variations of the materials was investigated as a function of variables, such as dopant $CdCl_2$ quantity and sintering temperature. When the process parameters were optimized, the maximum figure of merit was $2.146{\times}10^{-3}K^{-1}$.

• 연구논문집
• /
• s.22
• /
• pp.127-139
• /
• 1992

The mechnial properties such as fracture strength, ductility and fatigue strength of Cu shape memory alloy are lower than those of Ti-Ni SMA, because of their high elastic anisotropy and large grain size. And in order to improve the mechanical property of Cu SMA, some techniques such as casting method by addition of refining element, powder metallurgy and rapid solidification process have been studied on the refinement of the grain size of Cu SMA. This study was carried out to refine the grain size of CuAlNi SMA by applying the melt spinning method. According to this study, the conclusions are as follows; - grain size of the melt-spun ribbon was about $1\mum$ - there was not change in grain size, although increasing of hot pressing temperature -grain size of the hot-extruded specimen was about $30-40\mum$, it is more refiner than that of castings