• 제어로봇시스템학회:학술대회논문집
• /
• 1999.10a
• /
• pp.133-136
• /
• 1999

Many researches on the identification of a system have been carried out using a least square method, an adaptive filter, and so on. However, it is difficult to apply these methods in a nonlinear system. In the case of a nonlinear system, it is known that the signal compression method is able to estimate uncertain parameters of linear element in a nonlinear system because it is able to separate linear element and nonlinear element in a nonlinear system. However, the signal compression method cannot be applied to a motion simulator because actuators of the simulator is single-rod cylinders which includes expansion and compression dynamic properties. Therefore, this paper proposes a modified signal compression method which is able to estimate uncertain parameters of the motion simulator dynamics. The dynamic properties of this system are identified by separating expansion and compression properties when applying the signal compression method. And then, the identified parameters are applied to design a sliding mode controller for the simulator. The performance of the designed sliding mode controller is evaluated experimentally.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.4
• /
• pp.78-84
• /
• 2009

This paper presents development results of integrated operating program and its simulator for an inshore test miner. The inshore test miner drives on the seabed and collects manganese nodules. For operating the test miner, integrated operating program (IOP) is needed for remote control and monitor of the miner in real-time. However, it is hard to develop the practical IOP for the test miner system, because the system is big, expensive, and unique. So a simulator was developed as a test substitute in order to save time and to reduce cost. Using test results of the simulator, the IOP of the test miner was developed. The developed IOP consists of remote program, host program, monitoring program and database program. The operating program was developed using PXI and Labview of NI. The experimental results are presented to show the applicability of the developed program.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.11
• /
• pp.1069-1076
• /
• 2007

This paper presents the road simulator control technology for reproducing the road input signal to implement the real road data. The simulator consists of the hydraulic pump, servo valve, hydraulic actuator and its control equipment. The QFT(Quantitative Feedback Theory) is utilized to control the simulator effectively. The control system illustrates a tracking performance of the closed-loop controller with low order transfer function G(s) and pre-filter F(s) for a parametric uncertain model. A force controller is designed to communicate the control signal between simulator and digital controller. Tracking specification is satisfied with upper and lower bound tolerances on the steep response of the system to the reference signal. The efficacy of the QFT force controller is verified through the numerical simulation, in which combined dynamics and actuation of the hydraulic servo system are tested. The simulation results show that the proposed control technique works well under uncertain hydraulic plant system. The conventional software (Labview) is used to make up for the real controller in the real-time basis, and the experimental works show that the proposed algorithm works well for a single road simulator.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.2
• /
• pp.227-235
• /
• 2006

For a sophisticated humanoid that explores and learns its environment and interacts with humans, anthropomorphic physical behavior is much desired. The human vision system orients each eye with three-degree-of-freedom (3-DOF) in the directions of horizontal, vertical and torsional axes. Thus, in order to accurately replicate human vision system, it is imperative to have a simulator with 3-DOF end-effector. We present a 3-DOF anthropomorphic oculomotor system that reproduces realistic human eye movements for human-sized humanoid applications. The parallel link architecture of the oculomotor system is sized and designed to match the performance capabilities of the human vision. In this paper, a biologically-inspired mechanical design and the structural kinematics of the prototype are described in detail. The motility of the prototype in each axis of rotation was replicated through computer simulation, while performance tests comparable to human eye movements were recorded.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.2
• /
• pp.125-133
• /
• 2017

This paper presents the inter-rater reliability of finger spasticity assessment tested realized by using finger simulator that mimics finger spasticity of patients after a stroke. For controlling the simulator torque, finger spasticity was modeled, and the model parameters were obtained by measuring quantitative data while grading based on Modified Ashworth Scale (MAS). A robotic finger simulator was designed for mimicking finger spasticity. Evaluation of this simulator with the help of seven rehabilitation doctors showed that the simulator had a Cohen's kappa value of 0.619 for Metacarpophalangeal Joint and 0.514 for Proximal Interphalangeal Joint. Fleiss' kappa between raters is 0.513 for Metacarpophalangeal Joint and 0.486 for Proximal Interphalangeal Joint. Therefore, the spasticity assessment made by MAS grade system is not reliable owing to the subjectivity of the assessment. The proposed robotic simulator can be used as a training tool for improving the reliability of the spasticity assessment.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1749-1753
• /
• 2007

The reliability, that is Long-Term Quality, require an approaching different from Short-Term Quality which is used before. As the electronic components are able to be easily normalized on the reliability testing, various testing standards are used. In this study, we proposed two reliability simulator that is PoF(Physics of Failure)-based and failure rate models-based. PoF-based simulator is introduced based on CalceEP program that is created by University of Maryland. This simulator can be modified by user interface of properties and PoF models and operated on stand alone system. Failure rate models-based simulator introduced according to analyzing reliability prediction documents. Also, unified database including failure data models is built from existing MIL-HDBK-217F N2, PRISM, and Bellcore, and web-based simulator is developed. The developed reliability simulator will service of the PoF model, properties, failure rate model accumulated and its data by web and internet.

• Journal of Biomedical Engineering Research
• /
• v.24 no.4
• /
• pp.363-367
• /
• 2003

Contact area and pressure are important factors which directly influence a life of knee implants. Since implant's mechanical functions should be experimentally evaluated for clinical use, many studies using a knee simulator and a pressure sensor system have been conducted. However it has not been reported that the contact pressure's distribution of a knee implant motion was estimated in real-time during a gate cycle. Therefore. the objective of this study was to analyze the contact pressure distribution for the motion of a joint using the knee simulator and I-scan sensor system. For this purpose, we developed a force-controlled dynamic knee simulator to evaluate the mechanical performance of artificial knee joint. This simulator includes a function of a soft tissue and has a 4-degree-of-freedom to represent an axial compressive load and a flexion angle. As axial compressive force and a flexion angle of the femoral component can be controlled by PC program. The pressure is also measured from I-scan system and simulator to visualize the pressure distribution on the joint contact surfaces under loading condition during walking cycle. The compressive loading curve was the major cause for the contact pressure distribution and its center move in a cycle as to a flexion angie. In conclusion, this system can be used to evaluate to the geometric interaction of femoral and tibial design due to a measured mechanical function such as a contact pressure, contact area and a motion of a loading center.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.1
• /
• pp.14-22
• /
• 2010

Hybrid Electronic Vehicle (HEV) is one of the solutions of high oil price and environment problem. Recently, study of HEV is important for automobile industry. However HEV has a lot of components and there are many cases for assembling, it's impossible to test results from assembling by using real vehicles. To solve this problem, hybrid system simulator is required. The purpose of this study is to develop and optimize of engine module for hybrid system simulator. The commercial 1-D engine simulation program, WAVE is used to get the engine capacity and performance data and 1-D simulation model of base engine is compared with engine experiment results. Using the data, the engine module is developed based on the MATLAB Simulink. There are blocks of base engine, Single-CVVT engine and Dual-CVVT engine. The effect of acceleration and deceleration is applied to each engine block. In addition, the control and processing logics for CIS technology are developed. Finally the simulator operates FTP-72 mode test.

• Journal of Drive and Control
• /
• v.10 no.4
• /
• pp.1-6
• /
• 2013

With aggravation of environmental contamination and energy resource exhaustion, Hybrid Electric Vehicles (HEV) that can be economically operated with low fuel consumption are receiving greater attention. For performance improvement of such HEV, the development of efficient transmission can be seen as one of core technologies such as performance of components and driving strategy. Dual clutch transmission (DCT) is actively studied as a transmission type for HEV due to its advantages of having excellent power transmission efficiency based on manual transmission characteristic, resolving the problem of power interruption, and realizing driving convenience of automatic transmission (AT). In this paper, one diesel HEV equipped with 6-Speed DCT, modelled using MATLAB/Simulink, and a performance simulator developed for this vehicle are introduced. Driving simulation with driving cycles such as FTP75 and NYCC was performed using the developed performance simulator, and the simulated results regarding state of charge and fuel economy, when AT and DCT are applied to this diesel hybrid vehicle respectively, are compared. This performance simulator can be utilized to develop a control algorithm for improving the fuel economy of HEV with DCT.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.3
• /
• pp.292-300
• /
• 2011

Control systems in machinery equipment provide correction signals to motion units in order to reduce or cancel out the mismatches between sensor feedback signals and command or desired values. In this paper, we introduce a simulator for control characteristics of machinery equipment. The purpose of the simulator development is to provide mechanical system designers with the ability to estimate how much dynamic performance can be achieved from their design parameters and selected devices at the designing phase. The simulator has a database for commercial parts, so that the designers can choose appropriate components for servo controllers, motors, motor drives, and guide ways, etc. and then tune governing parameters such as controller gains and friction coefficients. The simulator simulates the closed-loop control system which is built and parameter-tuned by the designer and shows dynamic responses of the control system. The simulator treats the moving table as a 6 degrees-of-freedom rigid body and considers the motion guide blocks stiffness, damping and their locations as well as sensor locations. The simulator has been under development for one and a half years and has a few years to go before the public release. The primary achievements and features will be presented in this paper.