• 항공우주시스템공학회지
• /
• 제14권6호
• /
• pp.18-25
• /
• 2020

This study investigated the structural behaviors and safety of an electro-mechanical linear actuator and a load simulator with a plate spring. The material and dimensions of the plate spring were determined by theoretically calculating the stress and torsional angle for the rating load of the actuator. Thereafter, a flexible multibody dynamics (FMBD) analysis was conducted on the linear actuator and load simulator to confirm the performance of the load simulator and acquire the reaction forces acting on the actuator and simulator. The structural safety of the linear actuator and load simulator was evaluated via finite element analysis using the aforementioned reaction forces. Consequently, the proposed linear actuator and load simulator were determined to be structurally safe; however, the safety factors for the actuation rod and the housing on the actuator were excessively high. Therefore, the weight and cost must be reduced to improve their design parameters in the future.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.180-188
• /
• 2003

The vehicle simulator is a useful virtual reality system. The simulator enables engineers to effectively research and analyze various experiments. Therefore, the development of a specific vehicle simulator is required, and its performance must be verified. This paper verifies the performance of Pusan National University Vehicle Simulator. Human sensibility ergonomic tests of vehicle simulator were also executed. The sense of simulator motion was chosen as the standard of performance evaluation. The driver's senses were subdivided into senses of rectilinear and rotational velocities. This study extracted ergonomic sensibility words that can be used to evaluate the performance of the simulator As a practical application of simulator, the relation was studied between the sense of simulator motion and the characteristics of drivers, who are classified into their sexes and driving careers. A statistical method was applied to human sensibility ergonomic tests of vehicle simulator.

• 대한의용생체공학회:의공학회지
• /
• 제29권4호
• /
• pp.323-328
• /
• 2008

A patient with respiratory disorders such as a sleep apnea is increasing as the obese patient increase on the modern society. Positive Airway Pressure (PAP) devices are used in curing patient with respiratory disorders and turn out to be efficacious for patients of 75%. However, these devices are required for evaluating their performance to improve their performance by the mechanical breathing simulator. Recently, the mechanical breathing simulator was studied by the real time feedback control. However, the mechanical breathing simulator by an open loop control was specially required in order to analyze the effect of flow rate and pressure after operating the breathing auxiliary devices. Therefore the aims of this study were to make the mechanical breathing simulator by a piston motion and a valve function from the characteristic test of valve and motor, and to duplicate the flow rate and pressure profiles of some breathing patterns: normal and three disorder patterns. The mechanical simulator is composed cylinder, valve, ball screw and the motor. Also, the characteristic test of the motor and the valve were accomplished in order to define the relationship between the characteristics of simulator and the breathing profiles. Then, the flow rate and pressure profile of human breathing patterns were duplicated by the control of motor and valve. The result showed that the simulator reasonably duplicated the characteristics of human patterns: normal, obstructive sleep apnea (OSA), mild hypopnea with snore and mouth expiration patterns. However, we need to improve this simulator in detail and to validate this method for other patterns.

• 한국CDE학회논문집
• /
• 제19권4호
• /
• pp.423-433
• /
• 2014

For the proper decision making and responsibility enhancement for an unexpected accident in large-scale facilities, it is important to train operators or first responders to minimize potential human errors and consequences resulted from them. Simulation technologies, including human-computer interaction and virtual reality, enables personnel to participate in simulated hazardous situations with a safe, interactive, repetitive way to perform these training activities. For the development of accident response training simulator, it is necessary to define components comprising the simulator and to integrate them for the given training purpose. In this paper, we analyze requirements of the training simulator, derive key components, and design the training simulator. Based on the design, we developed a prototype training simulator and verified the simulator through experiments.

• Journal of Mechanical Science and Technology
• /
• 제17권2호
• /
• pp.221-229
• /
• 2003

In the virtual environment, reality can be enhanced by offering the motion based on a motion simulator in harmony with visual and auditory modalities. In this research the Stewart-Gough-platform-based motion simulator has been developed. Implementation of vehicle dynamics is necessary in the motion simulator for realistic sense of motion, so bicycle dynamics is adopted in this research. In order to compensate for the limited range of the motion simulator compared with the real vehicle motion, washout algorithm composed of high-pass filter, low-pass filter and tilt coordination is usually employed. Generally, the washout algorithm is used with fixed parameters. In this research a new approach is proposed to tune the filter parameters based on fuzzy logic in real-time. The cutoff frequencies of the filters are adjusted according to the workspace margins and driving conditions. It is shown that the washout filter with the fuzzy-based parameters presents better performance than that with the fixed ones.

• International Journal of Automotive Technology
• /
• 제7권2호
• /
• pp.161-166
• /
• 2006

This paper presents shift characteristics of a dual clutch transmission(DCT). To obtain the shift force, dynamic models of the DCT are constructed by using MATLAB/Simulink and considering the rotational inertia of every component and the target pre-select time. Dynamic models of the shift and clutch actuators are derived based on the experimental results of the dynamic characteristics test. Based on the dynamic model of the DCT synchronizer, control actuator and vehicle model, a DCT vehicle performance simulator is developed. Using the simulator, the shift force and speed of the relevant shafts are obtained. In addition, the torque and acceleration of actuators are calculated during the shift process by considering the engaging and disengaging dynamics of the two clutches. It is observed from the performance simulator that uninterrupted torque can be transmitted by proper control of the two clutches.

• 한국자동차공학회논문집
• /
• 제17권4호
• /
• pp.16-23
• /
• 2009

Driving simulators are useful tools not only to test the components of future cars but also to evaluate the telematics service and HMI (Human-Machine Interface). However driving simulators cannot be implemented to test and evaluate the telematics service system because the GPS (Global Positioning System) which contains basic functional support for the telematics module do not work in the VR (virtual reality) environment. This paper presents a method to implement telematics service to a driving simulator by developing the GPS simulator which is able to emulate GPS satellite signals consist of NMEA-0183 protocol and RS232C communication standards. It is expected that the driving simulator with the GPS simulator can be used to study HMI and human-factor evaluations of the commercial telematics system to realize the HiLES (Human-in-the-Loop Evaluation System).

• Journal of Mechanical Science and Technology
• /
• 제19권spc1호
• /
• pp.272-282
• /
• 2005

A vehicle driving simulator is a virtual reality device which makes a man feel as if he drove an actual vehicle. Unlike actual vehicles, the simulator has limited kinematical workspace and bounded dynamic characteristics. So it is difficult to simulate dynamic motions of a multi-body vehicle model. In order to overcome these problems, a washout algorithm which controls the workspace of the simulator within the kinematical limitation is needed. However, a classical washout algorithm contains several problems such as generation of wrong sensation of motions by filters in tilt coordination, requirement of trial and error method in selecting the proper cut-off frequencies and difficulty in returning the simulator to its origin using only high pass filters. This paper proposes a washout algorithm with new tilt coordination method which gives more accurate sensations to drivers. To reduce the time in returning the simulator to its origin, an algorithm that applies selectively onset mode from high pass filters and return mode from error functions is proposed. As a result of this study, the results of the proposed algorithm are compared with the results of classical washout algorithm through the human perception models. Also, the performance of the suggested algorithm is evaluated by using human perception and sensibility of some drivers through experiments.

• 전자공학회논문지
• /
• 제49권10호
• /
• pp.122-127
• /
• 2012

Nano-electro-mechanical (NEM) 메모리 시뮬레이터를 Matlab을 이용하여 개발하였다. 구현된 simulator는 이력 곡선, 빔의 변위에 따른 힘의 변화, 정상상태와 과도상태의 빔의 이동, 에너지 소모, 시스템의 포텐셜 에너지의 간편한 분석을 가능하게 한다. 개발된 NEM 메모리 시뮬레이터는 간단한 조작만으로 NEM 메모리의 거동을 관찰할 수 있으므로 NEM 메모리 셀의 간편한 설계를 가능하게 한다.

• Journal of Mechanical Science and Technology
• /
• 제18권3호
• /
• pp.471-480
• /
• 2004

Statistical simulation approaches are proposed to evaluate the shift feeling for a manual transmission. First, shift force simulator for the manual transmission is developed by considering the dynamic models of the external and internal linkage, synchronizer, and drivetrain. It is found that the shift force by the simulator shows a good correlation with the test results. Using the simulator, two kinds of statistical simulation approaches are proposed and the objective parameters that can be used to evaluate the shift feeling quantitatively are obtained. It is expected that the shift force simulator with the statistical approaches, developed in this study can be used as a useful design tool to evaluate the shift feeling in the initial design stage.