• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.311-318
• /
• 2018

When reinforced concrete structures are exposed to fire, their mechanical properties such as compressive strength, elasticity coefficient and rebar yield strength, are degraded. Therefore, the structure's damage assessment is essential in determining whether to dismantle or augment the structure after a fire. In this study, the confinement effect of lateral reinforcement of RC column according to the numbers of fire exposure face and stirrup was verified by fire resistant test with the heating temperatures of $400^{\circ}C$, $600^{\circ}C$ and $800^{\circ}C$. The test results showed that the peak stress decreases and peak strain increases as the temperature is getting higher, also transverse ties are helpful in improving the compressive resistance of concrete subjected to high temperature. Based on the results of this study, the residual stress of confined concrete under thermal damage is higher at the condition of more lateral reinforcement ratio and less fire exposure faces. The decreasing ratio of elastic modulus of more confined and less exposure faces from the relationship of load and displacement was also smaller than that of opposite conditions.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.4
• /
• pp.15-21
• /
• 2006

Composite materials were prepared by impregnating water glass into the wood, followed by soaking in solutions of boric acid or phosphoric acid. The effects of these treatments on the physical and mechanical properties of the specimens and especially on its heat resistance were investigated. 1) Weight Percent Gain (WPG)s increased with increase of concentrations of water glass. However, there was little relationship between treatment temperatures and WPG. Generally, WPGs of double treated specimens were higher than single treated ones. 2) Percent shrinkages in each directions of the specimens treated with water glass had higher value than other specimens. Percent shrinkages of the specimens treated with boric acid or phosphoric acid were decreased as compared with untreated specimen. However, the specimens treated with water glass or phosphoric acid showed very high hygroscopicity. 3) The bending strengths of all specimens treated inorganic substances were slightly decreased. However, the values of compressive strength and hardness of most specimens treated with inorganic substances increased or similar to that of untreated specimen except for a phosphoric acid treated specimens. 4) The specimens had good heat resistance. Weight losses of all specimens treated inorganic substances were about 50~70%. In particular, the specimens treated at $300^{\circ}C$ and $400^{\circ}C$ almost kept their shapes.

• Nuclear Engineering and Technology
• /
• v.56 no.1
• /
• pp.106-113
• /
• 2024

Understanding the tritium release and retention behavior of candidate tritium breeder materials is crucial for breeder blanket design. Recently, a melt spraying process was developed to prepare Li₄SiO₄ pebbles, which were subsequently subjected to the in-pile tritium production and extraction platform in China Mianyang Research Reactor (CMRR) to investigate their in-situ tritium release behavior and irradiation performance. The results demonstrate that HT is the main tritium release form, and adding hydrogen to the purge gas reduces tritium retention while increasing the HT percent in the purge gas. Post-irradiation experiments reveal that the irradiated pebbles darken in color and their grains swell, but the mechanical properties remain largely unchanged. It is concluded that the tritium residence time of Li₄SiO₄ made by melt spraying method at 467 ℃ is approximately 23.34 h. High-density Li₄SiO₄ pebbles exhibit tritium release at relatively low temperatures (<600 ℃) that is mainly controlled by bulk diffusion. The diffusion coefficient at 525 ℃ and 550 ℃ is 1.19 × 10^-11 cm²/s and 5.34 × 10^-11 cm²/s, respectively, with corresponding tritium residence times of 21.3 hours and 4.7 hours.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.2
• /
• pp.276-285
• /
• 2012

The objective of this research is to develop the coating technique by a porous self-fluxing alloy for improving the mechanical properties of run-out table roller surface with the hot rolling. To enhance the durability of run-out table roller with the hot rolling, the high hardness of roller surface should be maintained at high temperatures, and the improvement of wear resistance, corrosion resistance, heat resistance, burn resistance and adhesion resistance should be maintained. In order to be able to transport reliably a hot rolled steel sheet, also, the appropriate friction coefficient on the roller surface should be maintained and the slip between roller and steel should not occur. In this study, the wear resistance of roller increases after the self-fluxing alloy is changed to a cermet by adding the tungsten carbide(WC), and the coefficient of friction increases and the ability of grip is improved because the porosities are made by coating with fine iron powder on the roller surface. As a result, it is found that the ability of grip between the steel and the roller coated by a porous self-fluxing alloy contained to 5 ~ 10 wt% of Fe in the coating layer is improved compared to the roller coated by Ni-Cr. This is because the porosities are made after Fe contained in the roller is partially alloyed by heating with a furnace in the fusing process and the rest is eliminated by oxidation and dissolution.

• Food Science and Preservation
• /
• v.21 no.3
• /
• pp.308-314
• /
• 2014

The storage characteristics of milled rice produced using the dry-type (DT), semi-dry-type (SDT), and wet-type (WT) systems were studied. Immediately after rice was milled with these systems, storage experiments on the milled rice were conducted for 12 weeks at three temperatures (10, 20, and $30^{\circ}C$). As the storage period increased, the color (b value) and the fat acidity slowly increased, and the whiteness, moisture content, turbidity, solid matter, and number of total bacteria decreased. The effects of the storage temperature on the moisture content, total number of bacteria, and fat acidity were greater than those of the milling system type. The high storage temperature showed greater potential for increasing the moisture content and the fat acidity and decreasing the total number of bacteria. The initial moisture content of the sample produced using the WT milling system was higher than that of the other samples. Also, the initial turbidity and solid matter of the WT system sample were lower than those of the other samples, but the degree of the decrease was similar to that of the others as the storage period passed. These results showed that the system type and the storage temperature are important factors in the safe storage of wash-free rice. Specifically, the wet type milling system affected the initial quality properties, which made its safe storage period shorter than in the other types.