• 한국도로학회:학술대회논문집
• /
• 2002.10a
• /
• pp.271-276
• /
• 2002

• Journal of Mechanical Science and Technology
• /
• v.19 no.3
• /
• pp.731-742
• /
• 2005

A magnetic bearing even with multiple coil failure can produce the same decoupled magnetic forces as those before failure if the remaining coil currents are properly redistributed. This fault-tolerant, force invariance control can be achieved with simply replacing the distribution matrix with the appropriate one shortly after coils fail, without modifying feedback control law. The distribution gain matrix that satisfies the necessary constraint conditions of decoupling linearized magnetic forces is determined with the Lagrange Multiplier optimization method.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.8
• /
• pp.1086-1093
• /
• 1997

Conceptual system design of a multistage centrifugal air-compressor is the first loop of design procedure. The properly designed system is important for compactness, low manufacturing cost, easy controllability, fast extension for the new specification of the compressor. A simple procedure of conceptual system design is proposed in the present study using simple analysis. A few examples of the procedure for a real system are shown and several design aspects are discussed.

• Composites Research
• /
• v.34 no.4
• /
• pp.226-232
• /
• 2021

In this paper, development of tape-springs made of composite materials was conducted for the deployment structures along with design, analysis, fabrication, and numerical and experimental investigation of mechanical behavior of the tape-springs. To this end, the tape-springs were manufactured according to three stacking patterns, and numerical and experimental investigation were conducted to determine whether or not they were damaged during bending with various selected composite materials. Finally, optimal stacking patterns that do not cause damage were selected during bending. With this information, the four-point bending test was conducted to obtain the moment-rotation curves. From results, it was confirmed that the nonlinear hysteresis phenomenon of the tape-springs was properly realized according to folding and unfolding. Therefore, it was confirmed that the composite material tape spring was properly developed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.3
• /
• pp.293-300
• /
• 2013

This study used a water tank and wave maker to generate conditions similar to the real ocean environment. Given that the waves were properly generated in the water tank, a precise analysis indicated the quantitative value of the wave force acting on a body. A high-speed camera and wave-level gauge were used to measure the temporal wave motion and period. A series of artificial water waves were successfully generated using three different wave periods and amplitudes. Each of the waves captured by a high-speed camera was sinusoidal and did not maintain its shape properly without a wave absorber, but it was substantially improved and well shaped when the wave absorber was installed.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.4
• /
• pp.505-514
• /
• 2016

To study mechanical properties of fiberglass reinforced wood-based composite (FRWC), fiberglass with a diameter of $20{\mu}m$ was selected to prepare test specimens. Mechanical properties of fiberglass reinforced wood-based composite were determined by three-point-bending test while its microstructure was characterizes by scanning electron microscopy (SEM). The results showed that mechanical properties of fiberglass reinforced wood-based composite were superior to that of the wood fiberboard based on the contrasting mechanical curves and the analysis of fracture mechanism. It is believed that the material design with this "sandwich" structure brings a unique buffering capacity of fiberglass into play in the composites. So the specimen did not produce a sudden fracture failure at high level of applied loads because it had a bearing ability. The SEM analysis showed that the working strength of PVAc adhesive was high; under a bearing force, it could properly transfer a load. In addition, glass fiber mesh and wood fiber board combined well.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.2
• /
• pp.108-113
• /
• 2009

The mixing of two dissimilar aluminum alloys in friction stir welding (FSW) was investigated using etching. The results show that the materials from the retreating side mixed into the advancing side in rather narrow and elongated bands whereas the materials from the advancing side mixed into the retreating side in the form of thick bands and lobes. A computational method using smoothed particle hydrodynamics (SPH) is introduced as a way to properly describe the complex mixing behavior in FSW.

• Journal of the Korean Society of Visualization
• /
• v.16 no.1
• /
• pp.37-41
• /
• 2018

The two-fluid model is widely used for practical applications involving multi-phase flows in chemical reactor, nuclear reactor, desalination systems, boilers, and internal combustion engine. There are several modeling terms in the two-fluid model, which must be determined properly. This study suggests the best models for turbulent vertical bubbly flow.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1994.06a
• /
• pp.758-763
• /
• 1994

The work discusses the problems of modelling of the process of acoustic signal generation in machines. We have pointed out that in the task of minimizing of both moise and vibration, the key problem is identification of sources and paths of propagation, both in terms of their location and of definition of their characteristic features. Properly conducted identification makes possible the use of relatively simple mathematical models and this fact is particularly important for a broad application of the proposed methods in practice.

• Proceedings of the KSR Conference
• /
• 2001.05a
• /
• pp.155-161
• /
• 2001

In order to evaluate the sound transmission loss of a structure, a large reverberation room described by ISO is generally used. ISO test method is however for architectural structures, which is not properly implemented for small mechanical structures, such as rolling stocks. In this paper, evaluation procedure for railway vehicle structures has been proposed.