• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.1865-1870
• /
• 2014

Torque converter is a complex turbomachine used to transfer power smoothly from an engine to a transmission by lock-up clutch. A torque converter consists of the hydrodynamic clutch device and the lock-up clutch device. The retaining plate and driven plate are part of the lock-up clutch. The lock-up clutch connects directly to achieve the improvement of efficiency and fuel consumption. In this paper, using structure analysis of stress distribution on the shape of the mechanical stopper on retaining plate. The shape of mechanical stopper has effect on the stress distribution of lock-up clutch.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.9-15
• /
• 2006

Experiments are conducted to compare fuel economy of FTP-75 mode on two different lock-up conditions; (A) Lock-up on at engine speed of 1,200(rpm) and above for 3rd & 4th gear, (B) Lock-up on at engine speed of 1400rpm and above for 4th gear only. As a result, case A had better fuel economy about 2.75(%) than case B for FTP-75 mode. Simulation(CRUISE, AVL) study is also carried out in order to estimate the effect of Lock-up control strategy for vehicle fuel economy. The fuel economy simulation result agrees with the measured fuel economy within error of 2(%). The improved Lock-up control strategy is proposed by simulation.

• Journal of Aerospace System Engineering
• /
• v.17 no.1
• /
• pp.10-15
• /
• 2023

Wet multi-disk clutch, a power switching device of the ducted fan, was optimized and results were analyzed. The clutch was divided into two types depending on whether a mechanical lock-up was applied or not. It was optimized under each design condition. Transfer torque capacity, friction material surface pressure, friction surface temperature, and drag torque were calculated as factors to optimize the clutch. The volume of separator plate and drag torque were used as the objective function for optimization. In the case of Type 1, which did not include a mechanical lock-up, the clutch could be operated regardless of the pitch angle of the ducted fan. However, the outer diameter of the friction surface was doubled, the volume was increased by 5~7 times, and the drag torque was increased by 7~12 times compared to those of Type 2, which included a mechanical lock-up.

• Journal of Mechanical Science and Technology
• /
• v.17 no.4
• /
• pp.521-527
• /
• 2003

Modern automatic transmissions equip torque converters with lock-up clutches to reduce the energy loss of hydraulic systems. Instead of simply engaging the clutch disks, the new technology of clutch slip has been developed to improve the overall efficiency of power transmission. There are two major problems with the clutch slip system. The first is how to keep the slip between the two disks within a small range and the second is when to start or stop the slip. In this paper, the second problem is discussed in view of the vehicle economy. With a simple vehicle dynamic model, the fuel economy is calculated to determine the lock-up strategy. Then the lock-up strategy is developed for a slip schedule.

• International Journal of Automotive Technology
• /
• v.8 no.5
• /
• pp.599-603
• /
• 2007

An efficient optimum design process has been developed and applied to systematically design a lock-up clutch system for a torque converter used in an automatic transmission. A simulated annealing algorithm was applied to determine the parameters of the compressive helical damper springs in the clutch. The determination of the number, location, a number of turns, and deflection of damper springs plays an important role in reducing vibration and noise in the lock-up system. Next, FE-based shape optimization was coded to find the shape of the clutch disk that would satisfy the strength, noise and vibration requirements. Using the optimum code, parametric studies were performed to see how spring diameters and frequencies of clutch systems changed as the damper spring traveling angles and the torques were varied. Based on the optimum results, five different designs for clutches with different springs were fabricated and vibration analyses and tests were conducted to validate the accuracy of the proposed method. Results from the two methods show a good correlation.

• Tribology and Lubricants
• /
• v.21 no.3
• /
• pp.122-129
• /
• 2005

The floating ring seal has the ability of minimizing clearance without rubbing phenomenon. However, the seal ring can be unstable due to extremely high lock-up eccentricity ratio arisen from the poor design of height and surface finish of the ring. The exact prediction of the lock-up position of the floating ring is necessary to design the floating ring properly. The governing equations are developed and solved numerically. The test facility for the measurement of the boundary-lubrication-friction coefficient of the ring‘s surface has been established. Based on the results of analysis, the geometric conditions of the floating ring seal are suggested for operating at a low lock-up eccentricity ratio.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.8
• /
• pp.1129-1136
• /
• 2010

Damper springs in a drive-line absorb the impulsive torque generated when a lock-up clutch is connected directly, instead of via a fluid coupling. Design optimization and finite element analysis were performed to improve the shock- and vibration-absorption capacity of the lock-up clutch. For this purpose, a multi-body dynamics model was developed by including the main parts of a vehicle, such as an engine with a clutch, a transmission, drive shafts and wheels, and a whole mass of a vehicle. The spring constants were selected so that resonance of a system could be avoided. Damper springs were optimized on the basis of the spring constants, impulsive torques, compressed angles, spring counts, fatigue constraints, etc. Topology optimization was performed for three plates with the damper springs. The compliance was set up as an objective function, and volume fraction was fixed below 0.3. A new shape for the plates was proposed on the basis of the topology result.

• Journal of Drive and Control
• /
• v.21 no.1
• /
• pp.1-7
• /
• 2024

The locking performance of a multi-plate clutch with a mechanical lock-up system is governed by the engagement algorithm. In this paper, a control algorithm to improve the locking performance of the clutch was studied. A 1D dynamic model was constructed and simulated according to the developed algorithm. The developed algorithm was composed of a method in which the locking device is engaged while generating artificial slip on the friction plate by controlling the piston pressure of the clutch. Furthermore, a case study of the parameters within the developed algorithm was conducted to explore combinations that maximize locking performance and analyze trends according to these parameters.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.99-102
• /
• 2003

This paper aims to observe the micro-mechanical behaviour of tow geometry during deformation of dry woven carbon-fiber fabric. With the increment of shear angle fabric experiences 'lock-up'phenomenon. In this paper, deformation of micro-mechanical parameters such as tow interval, change in tow amplitude and wavelength are investigated. To observe the micro-deformation of the fabric structure, appropriate specimens from bias extension and biaxial tests are sectioned and observed under the microscope. It was found that different loading conditions cause geometric deferences in the tow architecture.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1334-1339
• /
• 2003

An efficient method is developed for the shape optimization of 2-D structures. The sequential linear programming is used for minimization problems. Selected set of master nodes are employed as design variables and assigned to move towards the normal direction. After adapting the nodes on the design boundary, the B-spline curves and mesh smoothing schemes are used to maintain the finite element in good quality. Finally, a numerical implementation of optimum design of an automobile torque converter piston subjected to pressure and centrifugal loads is presented. The results shows additional weight up to 13% may be saved after the shape optimization.