• Journal of Hydrogen and New Energy
• /
• v.20 no.1
• /
• pp.38-44
• /
• 2009

Recently, the research focused on fuel cell hybrid vehicles (FCHVs) is becoming an attractive solution due to environmental pollution generated by fossil fuel vehicles. The proper energy control strategy will result in extending the fuel cell lifetime, increasing of energy efficiency and an improvement of vehicle performance. Battery state of charge (SoC) is an important quantity and the estimation of the SoC is also the basis of the energy control strategy for hybrid electric vehicles. Estimating the battery's SoC is complicated by the fact that the SoC depends on many factors such as temperature, battery capacitance and internal resistance. In this paper, battery charging time estimated by SoC is studied by using the speed response and current response. Hybrid system is consist of a fuel cell unit and a battery in series connection. For experiment, speed response of vehicle and current response of battery were determined under different state of charge. As the results, the optimal battery charging time can be estimated. Current response time was faster than RPM response time at low speed and vice versa at high speed.

• Journal of Hydrogen and New Energy
• /
• v.24 no.2
• /
• pp.113-120
• /
• 2013

A steam reformer is a chemical reactor to produce high purity hydrogen from fossil fuel. In the steam reformer, since endothermic steam reforming is heated by exothermic combustion of fossil fuel, the heat transfer between two reaction zones dominates conversion of fossil fuel to hydrogen. Steam Reforming is complex chemical reaction, mass and heat transfer due to the exothermic methane/air combustion reaction and the endothermic steam reforming reaction. Typically, a steam reformer employs burner to supply appropriate heat for endothermic steam reforming reaction which reduces system efficiency. In this study, the heat of steam reforming reaction is provided by anode-off gas combustion of stationary fuel cell. This paper presents a optimization of heat transfer effect and average temperature of cross-section using two-dimensional models of a coaxial cylindrical reactor, and analysis three-dimensional models of a coaxial cylindrical steam reformer with chemical reaction. Numerical analysis needs to dominant chemical reaction that are assumed as a Steam Reforming (SR) reaction, a Water-Gas Shift (WGS) reaction, and a Direct Steam Reforming(DSR) reaction. The major parameters of analysis are temperature, fuel conversion and heat flux in the coaxial reactor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.193-197
• /
• 2003

As one of the core technologies in the field of the optical communication with WDM, the optical cross connector with movements of micro mirrors is getting important day by day. The packaging structure of 2-dimensional NxN MOEMS switch should be determined by the harmonization of the following items such as the geometrical compatability between optical and structural components, the characteristics of optical input and output parts with device, and the electrical performance for the operation of micro mirrors. Therefore, the packaging process could be defined as the integrated technology completed by the optical and electrical science and the material science for the understanding of its thermo-mechanical properties with packaging materials. In the present study, the harmonization between the optical and structural components as well as the optical characteristics of lens system used will be investigated.

• Journal of the Korean Geosynthetics Society
• /
• v.10 no.4
• /
• pp.93-103
• /
• 2011

In order to design suitable geo-structures in cold region, it is generally required to consider the mechanical properties of permafrost soils. 'Frost heave' as one of the primary phenomenon is considered to be an important factor together with 'adfreeze bond-strength' and 'creep deformation' for structural design process in permafrost area. Therefore, the fundamental study for frost heave has to be preceded for design of geo-structures in cold region. While various experimental apparatuses have been developed, there still exist a certain level of limitation to evaluate the frost-heave characteristics as design parameters. In this paper, a new type of experimental apparatus is proposed to evaluate the engineering characteristics of frost heave in permafrost soils and a set of verification test results is presented. Based on the verification tests, the proposed apparatus is a suitable to obtain frost characteristics of soils.

• Smart Structures and Systems
• /
• v.18 no.5
• /
• pp.955-982
• /
• 2016

Recent studies integrating vibration control and structural health monitoring (SHM) use control devices and control algorithms to enable system identification and damage detection. In this study real-time SHM is used to enhance structural vibration control and reduce damage. A newly proposed control algorithm, including integrated real-time SHM and semi-active control strategy, is presented to mitigate both damage and seismic response of the main structure under strong seismic ground motion. The semi-active independently variable stiffness (SAIVS) device is used as semi-active control device in this investigation. The proper stiffness of SAIVS device is obtained using a new developed semi-active control algorithm based on real-time damage tracking of structure by damage detection algorithm based on identified system Markov parameters (DDA/ISMP) method. A three bay five story steel braced frame structure, which is equipped with one SAIVS device at each story, is employed to illustrate the efficiency of the proposed algorithm. The obtained results show that the proposed control algorithm could significantly decrease damage in most parts of the structure. Also, the dynamic response of the structure is effectively reduced by using the proposed control algorithm during four strong earthquakes. In comparison to passive on and off cases, the results demonstrate that the performance of the proposed control algorithm in decreasing both damage and dynamic responses of structure is significantly enhanced than the passive cases. Furthermore, from the energy consumption point of view the maximum and the cumulative control force in the proposed control algorithm is less than the passive-on case, considerably.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.3
• /
• pp.233-242
• /
• 2011

This study aims to evaluate the applicability of high-strength concrete mixed with blast furnace slag to shield segment lining in order to improve its performance and economic efficiency. Especially, it was also intended to derive the optimum replacing ratio of ground granulated blast furnace slag to ordinary cement as well as the optimum steam curing condition for shield segment concrete with the design strength of 60 MPa. From a series of experiments, the condition of 50% replacement of ordinary cement by ground granulated blast furnace slag and unit water content of 125 kg/$m^3$ was proposed as the optimum mixing condition. Comparing with standard curing conditions, it was also possible to expect approximately 110~442% strength improvement of concrete by steam curing in the same mixing condition.

• Computers and Concrete
• /
• v.20 no.5
• /
• pp.563-572
• /
• 2017

Ordinary reinforced concrete (RC) and prestressed concrete bridges are two popular and typical types of short- and medium-span bridges that accounts for the vast majority of all existing bridges. The cost of maintaining, repairing or replacing degraded existing RC bridges is immense. Detecting the abnormality of RC bridges at an early stage and taking the protective measures in advance are effective ways to improve maintenance practices and reduce the maintenance cost. This study proposes a systematic method from influence line (IL) identification to damage detection with applications to RC bridges. An IL identification method which integrates the cubic B-spline function with Tikhonov regularization is first proposed based on the vehicle information and the corresponding moving vehicle induced bridge response time history. Subsequently, IL change is defined as a damage index for bridge damage detection, and information fusion technique that synthesizes ILs of multiple locations/sensors is used to improve the efficiency and accuracy of damage localization. Finally, the feasibility of the proposed systematic method is verified through experimental tests on a three-span continuous RC beam. The comparison suggests that the identified ILs can well match with the baseline ILs, and it demonstrates that the proposed IL identification method has a high accuracy and a great potential in engineering applications. Results in this case indicate that deflection ILs are superior than strain ILs for damage detection of RC beams, and the performance of damage localization can be significantly improved with the information fusion of multiple ILs.

• Journal of computational fluids engineering
• /
• v.18 no.3
• /
• pp.1-7
• /
• 2013

A pure oxygen combustion technology is crucial in Carbon Capture and Storage (CCS) technology especially in capturing of $CO_2$, where CCS will reduce 9 $GtCO_2$ by 2050, which is 19% of the total $CO_2$ reduction amount. To make pure oxygen combustion feasible, a regenerative system is required to enhance the efficiency of pure oxygen combustion system. However, an existing air combustion technology is not directly applicable due to the absence of nitrogen that occupies the 78% of air. This study, therefore, investigates the heat and fluid flow in a regenerative system for pure oxygen combustion by using commercial CFD software, FLUENT. Our regenerative system is composed of aluminium packed spheres. The effect of the amount of packed spheres in regenerator and the effect of presence or absence of a bypass of exhaust gas are investigated. The more thermal mass in regenerator makes the steady-state time longer and temperature variation between heating and regenerating cycle smaller. In the case of absence of bypass, the regenerator saturates because of enthalpy imbalance between exhaust gas and oxygen. We find that 40% of exhaust gas is to be bypassed to prevent the saturation of regenerator.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.1
• /
• pp.88-93
• /
• 2010

In this paper, an edge detecting sensor using ultrasonic detection module is developed which will be used for areas of industrial applications such as plastic film winding system, cloth winding system, paper roll industry, etc. The developed sensor have properties that more exactly detect the edge line, that less affected by environmental noise, and that it produced more stable measurement output. The mass of the winding object is dominantly affect the dynamics of the system and it could produce undesirable result of the system such as stability of the closed-loop system and accuracy of edge-line-following-control(ELFC) objective. Also, there exist sensor noise due to the mechanical vibration or other environmental effect. These noise also degrade the efficiency of control system. In order to compensate these problems, this paper present a fuzzy PI/PID edge-line-controller, and which is designed and implemented.

• Journal of Korean Society of Forest Science
• /
• v.83 no.3
• /
• pp.357-364
• /
• 1994

In this paper, the characteristics of cable logging systems, of which skyline length is adjustable during operation are discussed from a standpoint of system geometry. Among the cable logging systems, the live skyline is the typical one, of which operation is easy to understand. To analyze the cable logging mechanics of the live skyline, computer models were developed. In developing the computer models, the concept of the live skyline operation was classified into 'true live skyline' and 'live skyline with lift'. The former assumes to adjust skyline length continuously to maintain the skyline clearance over ground constant during inhaul ; the latter assumes to shorten the skyline length only to keep the minimum skyline clearance during inhaul. The computer model was used in investigating the mechanical efficiency and the operational characteristics of the live skyline system. First, the payload capability of live skyline was compared with that of standing skyline. Second, the effect of the change in the log-drag geometry on the payload capability of live skyline was investigated. Finally, the payload capability of live skyline with lift was compared with that of true live skyline as an effort to explain the concepts of true live skyline and live skyline with lift.