• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.719-724
• /
• 2016

This paper describes the performance improvement of an inrush current limiter to prevent damage or malfunctions in power converters due to the inrush current. When the power converter of military radar is operated, the circuit breaker of the power converter is often activated because the overcurrent flows through the circuit breaker of the power converter. Therefore, this study performed a cause analysis of the problem, which is a larger current flow than the intended current(250A). The operation principle of an inrush current limiter and SCR (Silicon Controlled Rectifier) used in the inrush current limiter was analyzed. As a result, the overcurrent flow through the circuit breaker was found to be due to dv/dt triggering of SCR. Based on cause analysis, this paper proposes a technique by adding the resistor in front of the SCR to prevent an unnecessary inrush current. Finally, the effectiveness of the improvement was verified by measuring the output current in the inrush current limiter. The power converter equipped with the improved inrush current limiter operated for more than 1 year without the circuit breaker of the power converter being activated.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.4
• /
• pp.449-455
• /
• 2019

This paper proposes a flyback diode of bridgeless PFC converter as SiC SBD (Schottky Barrier Diode) to achieve high efficiency. In addition, through the explanation of the operation principle of the bridgeless PFC converter, the conduction section of the freewheel diode is shown in the bridgeless PFC converter to verify the contribution of system loss due to the loss of the freewheel diode. The advantages of the SiC SBD device's physical properties and the reverse recovery characteristics are explained, and the efficiency is measured by measuring the turn-on and turn-off losses. The loss was calculated. The simulation results were calculated in consideration of device characteristics and verified through the waveform analysis and comparison of the actual system. In order to consider the device characteristics, the simulation was conducted using the thermal module of PSIM. As a result of the prototype test, the turn-on loss was 0.608W and the turn-off loss was 21.62W, resulting in the total switching loss of 22.228W. The comparison of the two results proved the validity of the experimental method. In addition, a high efficiency of 94.58% is achieved.

• The Journal of the Korea Contents Association
• /
• v.22 no.6
• /
• pp.69-77
• /
• 2022

Physical experiment through MBL has been used in many schools for a long time since students can check the experiment results immediately and conduct the experiment easily. However, conducting the experiment, not knowing the principle of the device or simply concentrating on the derived data has been raised as the problem of MBL experiment. To supplement this problem, this study measured the acceleration of gravity with the picket fence method, which is often used in MBL experiment, utilizing Arduino, calculated the error rate through a comparison to the actual acceleration of gravity and discussed the educational application of the experiment to measure it. As a result of the experiment, the error rate between the acceleration of gravity calculated by the experiment and the actual acceleration of gravity was about 1%, so it turned out that relatively accurate measurements were possible. Also, the sample mean of the experimental value was included in the confidence interval of 95%, so it could be concluded that it was a significant experiment. In addition, this study showed the possibility of the educational application of the experiment to measure it through the following: It can supplement the structural disadvantages of MBL; it can consider the interaction between Physics and Math; it is possible to converge with information course in STEAM education; and it is inexpensive to be equipped with the equipment. Hopefully, the physical experiment utilizing Arduino will further be revitalized in science gifted education based on this study.

• Journal of Bio-Environment Control
• /
• v.32 no.4
• /
• pp.484-491
• /
• 2023

Tomatoes in greenhouse are a widely cultivated horticultural crop worldwide, accounting for high production and production value. When greenhouse ventilation is minimized during low temperature periods, CO₂ enrichment is often used to increase tomato photosynthetic rate and yield. Plant-induced electrical signal (PIES) can be used as a technology to monitor changes in the biological response of crops due to environmental changes by using the principle of measuring the resistance value, or impedance, within the crop. This study was conducted to investigate the relationship between tomato growth data, vital response, and PIES resulting from CO₂ enrichment in greenhouse tomatoes. The growth of tomato treated with CO₂ enrichment in the morning was significantly better in all items except stem diameter compared to the control, and PIES values were also higher. The growth of tomato continuously applied with CO₂ was better in the treatment groups than control, and there was no significant difference in chlorophyll fluorescence and photosynthesis. However, PIES and SPAD values were higher in the CO₂ treatment group than control. CO₂ enrichment have a direct relationship with PIES, growth increased, and transpiration increased due to the increased leaf area, resulting in increased water absorption, which appears to be reflected in PIES, which measures vascular impedance. Through this, this study suggests that PIES can be used to monitor crops due to environmental changes, and that PIES is a useful method for non-destructively and continuously monitoring changes of crops.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.93-99
• /
• 2022

With the rapid development of ultra-small and wearable device technology, continuous electricity supply without spatiotemporal limitations for driving electronic devices is required. Accordingly, Triboelectric nanogenerator (TENG), which utilizes static electricity generated by the contact and separation of two different materials, is being used as a means of effectively harvesting various types of energy dispersed without complex processes and designs due to its simple principle. However, to apply the TENG to real life, it is necessary to increase the electrical output. In addition, stable generation of electrical output, as well as increase in electrical output, is a task to be solved for the commercialization of TENG. In this study, we proposed a method to not only improve the output of TENG but also to stably represent the improved output. This was solved by using the contact layer, which is one of the components of TENG, as an electret for improved output and stability. The utilized electret was manufactured by sequentially performing corona charging-thermal annealing-corona charging on the Fluorinated ethylene propylene (FEP) film. Electric charges artificially injected due to corona charging enter a deep trap through the thermal annealing, so an electret that minimizes charge escape was fabricated and used in TENG. The output performance of the manufactured electret was verified by measuring the voltage output of the TENG in vertical contact separation mode, and the electret treated to the corona charging showed an output voltage 12 times higher than that of the pristine FEP film. The time and humidity stability of the electret was confirmed by measuring the output voltage of the TENG after exposing the electret to a general external environment and extreme humidity environment. In addition, it was shown that it can be applied to real-life by operating the LED by applying an electret to the clap-TENG with the motif of clap.

• Journal of Intelligence and Information Systems
• /
• v.24 no.1
• /
• pp.101-124
• /
• 2018

Recently, most of the technologies have been developed in various forms through the advancement of single technology or interaction with other technologies. Particularly, these technologies have the characteristic of the convergence caused by the interaction between two or more techniques. In addition, efforts in responding to technological changes by advance are continuously increasing through forecasting promising convergence technologies that will emerge in the near future. According to this phenomenon, many researchers are attempting to perform various analyses about forecasting promising convergence technologies. A convergence technology has characteristics of various technologies according to the principle of generation. Therefore, forecasting promising convergence technologies is much more difficult than forecasting general technologies with high growth potential. Nevertheless, some achievements have been confirmed in an attempt to forecasting promising technologies using big data analysis and social network analysis. Studies of convergence technology through data analysis are actively conducted with the theme of discovering new convergence technologies and analyzing their trends. According that, information about new convergence technologies is being provided more abundantly than in the past. However, existing methods in analyzing convergence technology have some limitations. Firstly, most studies deal with convergence technology analyze data through predefined technology classifications. The technologies appearing recently tend to have characteristics of convergence and thus consist of technologies from various fields. In other words, the new convergence technologies may not belong to the defined classification. Therefore, the existing method does not properly reflect the dynamic change of the convergence phenomenon. Secondly, in order to forecast the promising convergence technologies, most of the existing analysis method use the general purpose indicators in process. This method does not fully utilize the specificity of convergence phenomenon. The new convergence technology is highly dependent on the existing technology, which is the origin of that technology. Based on that, it can grow into the independent field or disappear rapidly, according to the change of the dependent technology. In the existing analysis, the potential growth of convergence technology is judged through the traditional indicators designed from the general purpose. However, these indicators do not reflect the principle of convergence. In other words, these indicators do not reflect the characteristics of convergence technology, which brings the meaning of new technologies emerge through two or more mature technologies and grown technologies affect the creation of another technology. Thirdly, previous studies do not provide objective methods for evaluating the accuracy of models in forecasting promising convergence technologies. In the studies of convergence technology, the subject of forecasting promising technologies was relatively insufficient due to the complexity of the field. Therefore, it is difficult to find a method to evaluate the accuracy of the model that forecasting promising convergence technologies. In order to activate the field of forecasting promising convergence technology, it is important to establish a method for objectively verifying and evaluating the accuracy of the model proposed by each study. To overcome these limitations, we propose a new method for analysis of convergence technologies. First of all, through topic modeling, we derive a new technology classification in terms of text content. It reflects the dynamic change of the actual technology market, not the existing fixed classification standard. In addition, we identify the influence relationships between technologies through the topic correspondence weights of each document, and structuralize them into a network. In addition, we devise a centrality indicator (PGC, potential growth centrality) to forecast the future growth of technology by utilizing the centrality information of each technology. It reflects the convergence characteristics of each technology, according to technology maturity and interdependence between technologies. Along with this, we propose a method to evaluate the accuracy of forecasting model by measuring the growth rate of promising technology. It is based on the variation of potential growth centrality by period. In this paper, we conduct experiments with 13,477 patent documents dealing with technical contents to evaluate the performance and practical applicability of the proposed method. As a result, it is confirmed that the forecast model based on a centrality indicator of the proposed method has a maximum forecast accuracy of about 2.88 times higher than the accuracy of the forecast model based on the currently used network indicators.

• Journal of Korean Society of Forest Science
• /
• v.85 no.3
• /
• pp.539-551
• /
• 1996

In this study, a number of distance-dependent competition indices on tree-level which incorporate the tree sizes and distances to competitors, and traditional stand-level density measures were estimated from the data compiled with position-dependent survey in a Pinus densiflora stand. The performance of the estimated competition indices was examined by comparing the relationship with the diameter growth, and a dbh growth function, in which the competition index is considered as a one of influence factors, are developed. In the searching method of competing trees, the competition index estimated with $30^{\circ}$ competition interrupting angle showed the highest correlation with the annual dbh growth, while the expanding the competing zone distance had no significant effect on the performance of competition index in estimating annual dbh growth. The most of the examined stand-level competition indices, based on distance-dependent single-tree competition indices, were evaluated to describe similarly the stand competition status. As a result of partial correlation analysis in which the effect of age and site index are eliminated, Alemdag's mean competition index and relative spacing index were determined to have the highest correlation with dbh. The relative spacing index, which can be easily measured in field without measuring the position of individual trees, was considered to be a better suited one for estimating mean dbh of a stand. Among distance-dependent competition indices on tree-level, Hegyi's competition index showed the best performance in their correlation with annual dbh growth, if eliminated the effect of site index and dbh. This enabled to derive the following annual dbh growth function of individual trees which incorporate age, dominant height, dbh and Hegyi's competition index as influence factors : $$dbh^{\prime}=3.975362676{\cdot}age^{-1.099274613}{\cdot}ho^{0.199893990}{\cdot}dbh^{0.269430865}{\cdot}HgCI^{-0.353643587}$$ This function is coincided to the growth principle in which site index has a positive effect on the annual dbh growth, while high age or competition causes to reduce the annual dbh growth, and can be used as a function in single tree growth model.

• Journal of Yeungnam Medical Science
• /
• v.11 no.2
• /
• pp.230-239
• /
• 1994

In Order to evaluate determinants of successful percutaneous transluminal coronary angioplasty (PTCA), PTCA was performed for 172 coronary arterial lesions in 120 patients (89 male, 31 female) at Yeungnam university hospital from Sep. 1992 to Aug. 1993. The corinary artery luminal diameter at the site of the original stenosis was eveluated from end-diastolic frames of identical projections of the preangioplasty and immediate post angioplasty. The coronary luminal and balloon diameters were measured with using of computer measuring system. Overall success rate of 172 attempted lesions was 87.2%. Success rate of female patients was 93.5% and higher than those of male patients. According to the clinical diagnosis, success rate in stable angina was 93.7% and higher than those of post myocardial infarction angina, unstable angina and acute myocardial infarcrion. Success rate of American Heart Association type C lesion was 65.5% and lower those of type A (95.7%), type B (89.5%). There was signfifcantly difference in preangioplasty luminal stenosis, elastic recoil and length of lesion between successful PTCA group and failed PTCA group. Success rate of lesion location at a bend > $45^{\circ}$ and presence of intracoronary thrombus were lower than than those of other angiographic findings. In coclusion, primary angioplasty success was affected by specific angiographic factors. Stenosis severity, thrombus, lesion location at a bend > $45^{\circ}$, elastic recoil, and length of lesion were the principle of determinants of coronary angioplasty success rate.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.32 no.2 s.57
• /
• pp.105-110
• /
• 2006

This study was to describe the differences in efficacy and effect of herbal extracts by the part and solvent extraction from the medical plants used as materials of oriental herbs cosmetics. And, this study was to apply to the test method of efficacy and effect related to the antioxidation as herbal extracts, complex of actual ingredient, not existing analytical methods of single ingredient. After screening the medical plants with the antioxidative activity primarily and selecting 11 sorts of medical plants to be used by the part in the literature, this study was to confirm the differences through the well-known test methods like DPPH radical scavenging activity test and hydroxyl radical scavenging activity test. For examples, in case of Trachelospermum asiaticum, compared with the aerial part and fruit, the value of DPPH radical scavenging activity test had $25.2 {\pm} 0.2$ and $62.4 {\pm}1.6$ each. It has shown that the value of fruit had 2.4 times higher effect than the one of aerial part. In case of hydroxyl scavenging activity test, it was effective in the fruit, but it has shown that there was no effect on the aerial part. It showed the same phenomena in some other plants. From the result above, this researcher could understand that it needed to consider extracting the medical plants or plants with the active principle by the part. Also, this study was to confirm the differences in effect according to the solvent as it changed the solvent extraction after selecting a plant (Lithospermum erythrorhizon) widely used for medicine and dye. As a result of measuring the actual value of superoxide scavenging activity test, this study was to consider that there were differences by the part or solvent extraction in extracting and using the medical plants as it has shown that the effect differences produced $10{\sim}80%$ according to the solvent. When it was applied to the products, this study has shown that it needed to decrease the possible errors.

• Journal of Sasang Constitution and Immune Medicine
• /
• v.11 no.2
• /
• pp.95-117
• /
• 1999

1. Purpose of study There are many Constitution theories. But, In the Sasang Constitutional medicine, the theory and the practice are connected systematically. So it has been used in Korea popularly. Lee Je-Ma suggested that the external form, the mind, the symptom are the criteria of Sasang constitution diagnosis at the Discourse on the Four Principle and the Discourse on the Identifying Four Constitutions. But The clinical importance study of three diagnostic criteria - the external form, the mind, the symptom - has never been studied. Therefore, there are many obstacles of using the three diagnostic criteria totally. And I think that it needs a study which we apply the three diagnostic criteria to practice and approve the clinical importance of one another. I classify and investigate the previous methods of Sasang constitution diagnosis by the three diagnostic criteria in this study. 2. Method of study I investigate the previous methods of Sasang constitution diagnosis bibliographically by Dongyi Soose Bowon, Journal of Constitutional medicine and other books. 3. Result of study (1) Study of the external form The Study of Ki-sang(氣像) and Sa-ki(詞氣) by experience and intuition was done previously, and study of imaginay formulation of each constitution by measuring Chae-hyung(體形) and yong-mo(容貌) has being done recently. (2) Study of the mind For the objectification of study and diagnosis, self-reporting questionnaire has been used. The ideal choice to determine an indivisual constitution, as far as questionnaire go, is to take results from both the modified version Sasang Pattern Identification Questionnaire and QSCCII. (3) Study of the symptom For the study of the symptom - constitution symptom and constitution symptom of disease - the study of principles, the clinical study of the type of disease and symptom, the study which the pathologic view of Oriental medicine apply the view of Sasang Constitutional medicine have been done. We must try to objectfy Sasang Constitutional disease.