• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.1
• /
• pp.63-78
• /
• 2009

This paper presents the development of dynamically combined Typhoon generated surge-tide-wave numerical model which is applicable to shallow water. The newly developed model is based on both POM (Princeton Ocean Model) for the surge and tide and WAM (WAve Model) for wind-generated waves, but is modified to be applicable to shallow water. In this paper which is the first paper of the two in a sequence, we verified the accuracy and numerical stability of the hydrodynamic part of the model which is responsible for the simulation of Typhoon generated surge and tide. In order to improve the accuracy and numerical stability of the combined model, we modified algorithms responsible for turbulent modeling as well as vertical velocity computation routine of POM. Verification of the model performance had been conducted by comparing numerical simulation results with analytic solutions as well as data obtained from field measurement. The modified POM is shown to be more accurate and numerically stable compare to the existing POM.

• Structural Engineering and Mechanics
• /
• v.65 no.2
• /
• pp.173-181
• /
• 2018

In this paper, finite element (FE) model updating based on multi-objective optimization with the surrogate model for a steel plate girder bridge is investigated. Conventionally, FE model updating for bridge structures uses single-objective optimization with finite element analysis (FEA). In the case of the conventional method, computational burden occurs considerably because a lot of iteration are performed during the updating process. This issue can be addressed by replacing FEA with the surrogate model. The other problem is that the updating result from single-objective optimization depends on the condition of the weighting factors. Previous studies have used the trial-and-error strategy, genetic algorithm, or user's preference to obtain the most preferred model; but it needs considerable computation cost. In this study, the FE model updating method consisting of the surrogate model and multi-objective optimization, which can construct the Pareto-optimal front through a single run without considering the weighting factors, is proposed to overcome the limitations of the single-objective optimization. To verify the proposed method, the results of the proposed method are compared with those of the single-objective optimization. The comparison shows that the updated model from the multi-objective optimization is superior to the result of single-objective optimization in calculation time as well as the relative errors between the updated model and measurement.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.18 no.3
• /
• pp.97-113
• /
• 2023

In order to generalize the social entrepreneurship model with cooperation orientation and increase the possibility of using the model, this study developed a measurement tool and tested it with 389 executives of social enterprises. For the development of the measurement tool, preliminary measurement items were formed through review of previous studies, and a questionnaire was tentatively composed of 40 measurement items in five areas through an expert panel review of the measurement items. A total of 389 questionnaires were collected by conducting a questionnaire survey targeting Korean social enterprise managers, and exploratory and confirmatory factor analysis were conducted using 375 questionnaires that could be analyzed. Five factors for 24 items were derived through exploratory factor analysis and reliability analysis. Through a series of analysis processes including primary and secondary confirmatory factor analysis, the model fit of the newly constructed social entrepreneurship research model was confirmed, and the validity and reliability of the measurement tools were verified. As a result of this study, the model fit of the social entrepreneurship model(social value orientation; innovativeness; pro-activeness; risk-taking; cooperation orientation) is verified, thereby improving the theoretical explanatory power of social entrepreneurship research and at the same time providing the basis and basis for theoretical expansion of follow-up research. The study proved the possibility of generalizing the social entrepreneurship model with added cooperation orientation, and at the same time, the measurement tool used in this study was widely used as a tool to measure social entrepreneurship theoretically and practically. In addition, it was confirmed that the cooperation orientation is manifested in corporate decision-making and activity behaviors for resource mobilization and capacity building, opportunity and performance creation, social capital and network reinforcement, and governance establishment of social enterprises.

• International Journal of Automotive Technology
• /
• v.5 no.1
• /
• pp.33-46
• /
• 2004

A finite element model development of a 50th percentile male cervical spine is presented in this paper. The model consists of rigid, geometrically accurate vertebrae held together with deformable intervertibral disks, facet joints, and ligaments modeled as a series of nonlinear springs. These deformable structures were rigorously tuned, through failure, to mimic existing experimental data; first as functional unit characterizations at three cervical levels and then as a fully assembled c-spine using the experimental data from Duke University and other data in the NHTSA database. After obtaining satisfactory validation of the performance of the assembled ligamentous cervical spine against available experimental data, 22 cervical muscle pairs, representing the majority of the neck's musculature, were added to the model. Hill's muscle model was utilized to generate muscle forces within the assembled cervical model. The muscle activation level was assumed to be the same for all modeled muscles and the degree of activation was set to correctly predict available human volunteer experimental data from NBDL. The validated model is intended for use as a post processor of dummy measurement within the simulated injury monitor (SIMon) concept being developed by NHTSA where measured kinematics and kinetic data obtained from a dummy during a crash test will serve as the boundary conditions to "drive" the finite element model of the neck. The post-processor will then interrogate the model to determine whether any ligament have exceeded its known failure limit. The model will allow a direct assessment of potential injury, its degree and location thus eliminating the need for global correlates such as Nij.

• Journal of the Korea Society of Computer and Information
• /
• v.28 no.9
• /
• pp.177-188
• /
• 2023

The purpose of this study is to develop and validate a scale for measuring digital literacy by identifying the factors consisting of digital literacy and extracting items for each factor. Preliminary items for the Delphi study were developed through the analysis of previous literature and the deliberation of the research team. As a result of two rounds of the expert Delphi study, 65 items were selected for the main survey. The validation of the items was carried out in the process of exploratory and confirmatory factor analyses, reliability test, and criterion validity test using the data collected in the main survey. As a result, a 4-factor structure composed of 31 questions(factor 1: digital technology & data literacy- 9 questions, factor 2: digital content & media literacy- 8 questions, factor 3: digital communication & community literacy- 9 questions, factor 4: digital wellness literacy - 5 questions) was confirmed. Also, the goodness of fit indices of the model were found to be good and the result of reliability test revealed the scale had a very appropriate level of Cronbach's alpha(α=.956). In addition, a statistically significantly positive correlations(p<.001) were found between digital literacy and internet self-efficacy and between digital literacy and self-directed learning ability, which were predicted in the existing evidence, therefore the criterion validity of the developed scale was secured. Finally, practical and academic implications of the study are provided and future study and limitations of the study are discussed.

• Women's Health Nursing
• /
• v.26 no.4
• /
• pp.326-335
• /
• 2020

Purpose: This study was conducted to evaluate the construct validity, reliability, measurement invariance, and latent mean differences in the Breastfeeding Adaptation Scale-Short Form (BFAS-SF) for use with mothers at 2 weeks postpartum. Methods: This methodological study was designed to evaluate the validity, reliability, and measurement invariance of the BFAS-SF at 2 weeks postpartum, with data collected from 431 breastfeeding mothers. Confirmatory factor analysis and multi-group confirmatory factor analysis were conducted to assess the factor structure and the measurement invariance across employment status, delivery mode, parity, and previous breastfeeding experience, and the latent mean differences were then examined. Results: The goodness of fit of the six-factor model at 2 weeks postpartum was acceptable. Multi-group confirmatory factor analysis supported strict invariance of the BFAS-SF across employment status and delivery mode. Full configural invariance, full metric invariance, and partial scalar invariance across parity and full configural invariance and full metric invariance across previous breastfeeding experience were supported, respectively. The results for latent mean differences suggested that mothers who were employed showed significantly higher scores for breastfeeding confidence. Mothers who had a vaginal delivery showed significantly higher scores for sufficient breast milk and baby's feeding capability. Multiparous mothers showed significantly higher scores for baby's feeding capability and baby's satisfaction with breastfeeding. Conclusion: The validity and reliability of the BFAS-SF at 2 weeks postpartum are acceptable. It can be used to compare mean scores of breastfeeding adaptation according to employment status, delivery mode, and parity.

• Journal of Korea Water Resources Association
• /
• v.52 no.12
• /
• pp.1047-1055
• /
• 2019

Various types of numerical modeling techniques are used to predict the behavior of pollutants under various water environmental conditions in the event of a water pollutant accident. Among them, a hydraulic model that can consider water flow characteristics is the most basic and very important. The process of evaluating whether the hydraulic model accurately predicts the applied river characteristics is very important. In the verification of the modeling result, the measuring data are often used in the river. Currently, ADCP and FlowTrackers are widely used to measure the flow velocity of rivers. However, ADCP is not accurate when the depth is less than 0.6 m and also when the ratio of irreversibility near the surface is more than 40%. Futhermore, FlowTracker has a limitation in measuring at high depth and high velocity due to the direct measurement method in rivers. Simuation results, which are validated by these methods, are not reliable for low depth conditions of low flowrate and high velocity conditions of high flowrate. In this study, Lagrangian GPS floaters which measures physical quantity of water according to particle movement is used without the conventional method measured by Eulerian technique. The verification method of the model results was studied by comparing the simulation results of the hydraulic model with the velocities measured using the GPS floaters. When comparing the traveling distance of the GPS floaters with the traveling distance of the LPT simulations, the average error rate was 13.6% on distances, and the average error rate was 3.2% on velocities except for the stagnant section. Therefore, GPS floaters can be used for a correction and verification method of hydraulic model simulations.

• Land and Housing Review
• /
• v.9 no.4
• /
• pp.25-32
• /
• 2018

Application of geothermal energy in buildings has been gaining popularity as it provides the benefits of both heating and cooling a building. Among the various types of geothermal energy systems, ground-coupled heat pump system is the most commonly applied one in South Korea. A ground heat exchanger plays an important role as a heat source in winter and a heat sink in summer. For the stable operation of a ground-coupled heat pump system, a ground heat exchanger should be sized so that it provides sufficient heating and cooling energy. Heating and cooling energies generated in ground heat exchangers mainly depend on the temperature difference between the heating medium in ground heat exchangers and the surrounding ground. In addition, the performance of ground heat exchangers influences the change in ground temperature. Therefore, it is necessary to consider this interrelation between the change in the ground temperature and the performance of ground heat exchanger for an accurate estimation of its performance. However, previous thermal analysis models for ground heat exchangers are not competent enough to allow a complete understanding of this interrelation. Therefore, this study proposes a three-dimensional equivalent, transient ground heat exchanger analysis model. First, a previous thermal analysis model for ground heat exchangers, including an analytical model, a g-function, and a numerical model are analyzed. Next, to overcome the limitations of the previous models, a three-dimensional equivalent, transient ground heat exchanger model is proposed. Finally, this study validated the proposed model with the measurement data of the thermal response test, sandbox test, and TRNSYS DST model. All validation results showed a good agreement. These findings helped us to investigate the thermal performance of ground heat exchangers more accurately than the analytical models, and faster than the numerical models. Furthermore, the proposed model contributes to the design of ground heat exchangers by considering the different operation conditions of buildings.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.17 no.2
• /
• pp.156-172
• /
• 2014

This research measures and compares on-site net radiation energy, air temperature, wind speed, and surface temperature considering various spatial characteristics with a focus on land use types in urban areas in Changwon, Southern Gyeongsangnam-do, to analyze the accuracy of an ENVI-met model, which is an analysis program of microclimate. The on-site measurement was performed for three days in a mobile measurement: two days during the daytime and one day during the nighttime. The analysis using the ENVI-met model was also performed in the same time zone as the on-site measurement. The results indicated that the ENVI-met model showed higher net radiation than the on-site measurement by approximately $300Wm^{-2}$ during the daytime whereas the latter showed higher net radiation energy by approximately $200Wm^{-2}$ during the nighttime. The temperature was found to be much higher by approximately $2-6^{\circ}C$ in the on-site measurement during both the daytime and nighttime. The on-site measurement also showed higher surface temperature than the ENVI-met by approximately $7-13^{\circ}C$. In terms of the wind speed, there was a significant difference between the results of the ENVI-met model and on-site measurement. As for the correlation between the results of the ENVI-met model and on-site measurement, the temperature showed significantly high correlation whereas the correlations for the net radiation energy, surface temperature, and wind speed were very low. These results appear to be affected by excessive or under estimation of solar and terrestrial radiation and climatic conditions of the surrounding areas and characteristics of land cover. Hence, these factors should be considered when applying these findings in urban and environment planning for improving the microclimate in urban areas.

• Journal of ILASS-Korea
• /
• v.25 no.1
• /
• pp.8-14
• /
• 2020

Recently, 1-D model-based engine development using virtual engine system is getting more attention than experimental-based engine development due to the advantages in time and cost. Injection rate profile is the one of the main parameters that determine the start and end of combustion. Therefore, it is essential to set up a sophisticated model to accurately predict the injection rate as starting point of virtual engine system. In this research, procedure of 1-D model setup based on AMESim is introduced to predict the dynamic behavior and injection rate of diesel injector. As a first step, detailed 3D cross-sectional drawing of the injector was achieved, which can be done with help of precision measurement system. Then an approximate AMESim model was provided based on the 3D drawing, which is composed of three part such as solenoid part, control chamber part and needle and nozzle orifice part. However, validation results in terms of total injection quantity showed some errors over the acceptable level. Therefore, experimental work including needle movement visualization, solenoid part analysis and flow characteristics of injector part was performed together to provide more accuracy of 1-D model. Finally, 1-D model with the accuracy of less than 10% of error compared with experimental result in terms of injection quantity and injection rate shape under normal temperature and single injection condition was established. Further work considering fuel temperature and multiple injection will be performed.