• Journal of Astronomy and Space Sciences
• /
• 제27권4호
• /
• pp.337-343
• /
• 2010

Optical observation system provides angle-only measurement for orbit determination of space object. Range measurement can be directly acquired using laser ranging or tone ranging system. Initial orbit determination (IOD) by using angle- only data set shows discrepancy according to the measurement time interval. To solve this problem, range measurement data should be added for IOD. In this study, two-site optical observation was used to derive the range information. We have observed nine geostationary earth orbit satellites by using two-site optical observation system. The determination result of the range shows the accuracy over 99.5% compared to the results from the satellite tool kit simulation. And we confirmed that the orbit determination by the Herrick-Gibbs method with the range information obtained from the two-site observation is more accurate than the orbit determination by Gauss method with the one-site observation. For more accurate two-site optical observation, a baseline should satisfy an optimal condition of length and more precise observation system needed.

• 한국해양공학회지
• /
• 제24권4호
• /
• pp.72-77
• /
• 2010

This paper presents a method for measuring the shaft power of a marine main engine. Usually, in traditional systems for measuring shaft power, a strain gauge is used even though it has several disadvantages. First, it is difficult to set up the strain gauge on the shaft and acquire the correct signal for analysis. Second, it is very expensive and complicated. For these reasons, we investigated alternative approaches for measuring shaft power and proposed a new method that uses a vision-based measurement system. For this study, templates for image processing and CCD cameras were installed at the both ends of the shaft. Then, in order for the cameras to capture the images synchronously, we used a trigger mark and a optical sensor. The position of each template between the first and the second camera images were compared to calculate the torsion angle. The proposed measurement system can be installed more easily than traditional measurement systems and is suitable for any shaft because it does not contact the shaft. With this approach, it is possible to measure the shaft power while a ship is operating.

• 한국항공우주학회지
• /
• 제31권10호
• /
• pp.105-111
• /
• 2003

위성체 정렬은 위성체 조립 및 시험과정에서 중요한 부분이다. 인공위성이 우주궤도상에서 성공적인 임무를 수행하기 위해서는 자세제어 및 탑재체용 부분품들에 대하여 측정허용오차 $0.1^{\circ}{\sim}0.7^{\circ}$의 정밀하고 정확한 측정이 요구되며 정렬된 상태에서의 위성체 좌표계의 정확한 방향좌표를 측정하여 지상에 위치한 위성체 관제부에서 위성체의 자세제어 등에 사용하도록 제공하게 된다. 본 논문에서는 자동시준에 의한 위성체 정렬 측정 이론에 대하여 기술하고 데오도라이트를 사용하여 위성체 정렬을 측정할 수 있는 측정방법 및 그 측정 결과에 대하여 고찰해 보고자 한다.

• 한국기계가공학회지
• /
• 제18권8호
• /
• pp.74-81
• /
• 2019

Cars are inspected in the transport sector for their ability to achieve the greenhouse gas reduction targets. A vehicle (automobile) inspection broadly consists of regular and total checks, and both the safety level and the amount of exhaust gas are checked simultaneously during a vehicle inspection. This study deals with the efficiency of a soot probe to measure soot emissions from diesel vehicles. When the vehicle exhaust gas measurement is performed, there may be a difference between the exhaust gas temperature and the soot suction amount because of the different shape and angle of the exhaust port for each vehicle type. This may result in some incidents where the correct inspection nonconforming vehicle is not selected. Therefore, in this study, the shape of the probe was improved to increase the soot measurement efficiency under the condition of the exhaust pipe angle change.

• 로봇학회논문지
• /
• 제14권1호
• /
• pp.58-64
• /
• 2019

The paper proposes a stiffness measurement device composed of a measurement part including six indenters and a fixing part including four fixtures. The device is able to make simultaneously measurements of the stiffness of human arm. The six indenters make use of both position and force control schemes sequentially whenever needed. In addition, the loadcells and the digital encoders are attached to the indenters and electric motors, respectively, so that the data can be provided in real time. On the end of the indenter, two-axis potentiometer is attached in order to measure the angle difference between the applied force axis and the axis normal to the skin of human arm, and to convert the force measured on the loadcell into the actual applied force to skin. For this purpose, the mapping between the voltage output and the angle of potentiometer was obtained by fitting it for each axis. Ultimately, the measurement device was able to measure the stiffnesses of six regions of human arm.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.181.2-181.2
• /
• 2015

Sputtering is one of the most popular physical deposition methods due to their versatility and reproducibility. Synthesis of Cr thin films by DC magnetron sputtering using glancing angle deposition (GLAD) has been reported. Chromium thin films have been prepared at two different working pressure($2.0{\times}10-2$, 30, $3.3{\times}10-3torr$) on Si-wafer substrate using magnetron sputtering with glancing angle deposition (GLAD) technique. The thickness of Cr thin films on the substrate was adjusted about 1 mm. The electrical property was measured by four-point probe method. For the measurement of density in the films, an X-ray reflectivity (XRR) was carried out. The sheet resistance and column angle increased with the increase of glancing angle. However, nanohardness and density of Cr thin films decreased as the glancing angle increased. The measured density for the Cr thin films decreased from 6.1 to 3.8 g/cc as the glancing angle increased from $0^{\circ}$ to $90^{\circ}$ degree. The low density of Cr thin films is resulted from the isolated columnar structure of samples. The evolution of the isolated columnar structure was enhanced at the conditions of low sputter pressure and high glancing angle. This GLAD technique can be potentially applied to the synthesis of thin films requiring porous and uniform coating such as thin film catalysts or gas sensors.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.199-202
• /
• 2002

Interfacial properties and electrical sensing for fiber fracture in carbon and SiC fibers/epoxy composites were investigated by the electrical resistance measurement and fragmentation test. As fiber-embedded angle increased, interfacial shear strength (IFSS) of two-type fiber composites decreased, and the elapsed time was long to the infinity in electrical resistivity. The initial slope of electrical resistivity increased rapidly to the infinity at higher angle, whereas electrical resistivity increased gradually at small angle. Furthermore, both fiber composites with small embedded angle showed a fully-developed stress whitening pattern, whereas both composites with higher embedded angle exhibited a less developed stress whitening pattern. As embedded angle decreased, the gap between the fragments increased and the debonded length was wider for both fiber composites. Electro-micromechanical technique can be a feasible nondestructive evaluation to measure interfacial sensing properties depending on the fiber-embedded angle in conductive fiber reinforced composites.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 춘계학술발표대회 논문집
• /
• pp.55-60
• /
• 2008

This study is on the analysis of power output of transparent thin-film PV windows which are integrated into the building envelope instead of traditional windows. 3 installation angles of vertical, horizontal and $30^{\circ}C$ inclination are investigated. To measure power output of PV windows, full scale mock-up house was designed and constructed. The power performance of PV window system was analyzed for horizontal angle, declination angle and vertical angle according to incline angle. Monitoring data are gathered from November 2006 to August 2007 and statistical analysis is performed to analysis a characteristics of power performance of transparent PV windows. Results show that annual power output of PV window with horizontal angle is 844.4kWh/kWp/year, declination angle 1,060kWh/kWp/year and vertical angle 431.6 kWh/kWp/year.

• 한국항행학회논문지
• /
• 제22권6호
• /
• pp.500-506
• /
• 2018

본 논문에서는 유도탄의 정확한 자세를 알기 위해 주 관성항법장치와 유도탄 내부 관성항법장치를 이용하는 one-shot 정렬에 대해 고려하였다. One-shot정렬을 수행하기 위해서는 주 관성항법장치와 부 관성항법장치 사이의 비정렬각을 구해야 되는데, 장입유도탄과 부 관성항법장치 사이의 비정렬각을 구하여 보상하면 된다. 비정렬각은 장입유도탄의 롤 회전을 이용하여 산출되며, 장입유도탄을 회전하기 위한 정렬용 치구, 장입유도탄의 수평 상태를 측정하기 위한 수평각도계와 인터페이스 구조물이 제작되었다. TAS(tilt angle save) 점검 결과, 비정렬각 ${\alpha}$, ${\beta}$, ${\gamma}$ 값이 정상 범위이며 이 값을 보상하여 one-shot 정렬을 수행할 수 있다.

• 대한족부족관절학회지
• /
• 제14권2호
• /
• pp.161-164
• /
• 2010

Purpose: The purpose of this study is to find out the normal angles of the talus-1st metatarsal angle, the talo-horizontal angle and calcaneal pitch angle for diagnosis of foot deformity in Korea. This would be helpful as it would provide a basic angular measurement of flat and cavus foot that indicates the need for operation. Materials and Methods: Within a period of four months from January 2007 to April 2007, We have established 600 feet of 300 males without trauma history of foot. The source to image distance is 40 inches and erect weight bearing radiographs are obtained in anteroposterior and lateral projections. The significant angular measurements that define flat or cavus foot are the talus-1st metatarsal angle, the talo-horizontal angle and calcaneal pitch angle. Results: The mean age was 21 years (19-22 years) old. The mean talus-1st metatarsal angle was $0{\pm}6.9{^{\circ}}$, the mean talo-horizontal angle was $25.8{\pm}4.5{^{\circ}}$ and the mean calcaneal pitch angle was $23.9{\pm}5.1{^{\circ}}$. Conclusion: We can consider that mean talus-1st metatarsal angle, talo-horizontal angle and calcaneal pitch angle are $0{\pm}6.9{^{\circ}}$, $25.8{\pm}4.5{^{\circ}}$ and $23.9{\pm}5.1{^{\circ}}$ as an normal angle limit of young age in Korea.