• Clean Technology
• /
• v.27 no.1
• /
• pp.61-68
• /
• 2021

Selective catalytic reduction (SCR) is widely used as a method of removing nitrogen oxide in large-capacity thermal power generation systems. Uniform mixing of the injected ammonia and the inlet flue gas is very important to the performance of the denitrification reduction process in the catalyst bed. In the present study, a computational analysis technique was applied to the ammonia injection system design process of a denitrification facility. The applied model is the denitrification facility of an 800 MW class coal-fired power plant currently in operation. The flow field to be solved ranges from the inlet of the ammonia injection system to the end of the catalyst bed. The flow was analyzed in the two-dimensional domain assuming incompressible. The steady-state turbulent flow was solved with the commercial software named ANSYS-Fluent. The nozzle arrangement gap and injection flow rate in the ammonia injection system were chosen as the design parameters. A total of four (4) cases were simulated and compared. The root mean square of the NH3/NO molar ratio at the inlet of the catalyst layer was chosen as the optimization parameter and the design of the experiment was used as the base of the optimization algorithm. The case where the nozzle pitch and flow rate were adjusted at the same time was the best in terms of flow uniformity.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.4
• /
• pp.438-446
• /
• 2006

A lab-scale batch test was conducted to develop capping materials to reduce the sediment phosphorus in the stagnant water zone of Gyeongancheon in Paldang Lake. The mean grain size(Mz) of sediment in the investigated area was 7.7 ${\phi}$, which is very fine, and the contents of organic carbon($C_{org}$) was 2.4%, which is very high. For the phosphorous release experiment to select the optimal capping material, sand layer, powder-gypsum($CaSO_4{\cdot}2H_2O$), granule-gypsum, complex layer(gypsum+sand) and the control were compared and evaluated in the 150 L reactor for 45 days. In case of the capping with the sand, it was found that the phosphorous from the sediment could be reduced by around 50%. However, it was found that this caused the reduction of the dissolved oxygen in the water column(by less than 3 mg/L) due to the resuspension of sediment and the organic matter decomposition that comes from the generation of $CH_4$ gas in the 1 cm of the sand layer. Therefore, it is likely that the sand layer has to be thickener in case of the sand capping. Powder-gypsum and granule-Gypsum reduced phosphorous release by more than 80%. However, the concentration of ${SO_4}^{2-}$ in the water column increased, making it difficult to apply it to the drinking water protection zone. We developed Fe-Gypsum and $SiO_2$-gypsum materials to reduce the solubility of ${SO_4}^{2-}$. Powder-Gypsum creates the interception film that does not have any aperture on the sediment layer when it is combined with the water. However phosphorous release caused by the generation of $CH_4$ gas may happen at a time when the gypsum layer has the crack. Capping through the complex layer(granule-Gypsum+sand(1 cm)) found to be suitable for the drinking water protection zone because it was effective to prevent phosphorus release. Moreover, this leads to the lower solubility from the concentration of ${SO_4}^{2-}$ into the water column than the powder-Gypsum and granule-Gypsum. The addition of gypsum($CaSO_4{\cdot}2H_2O$) into the sediment can reduce the progress of methanogensis because fast early diagenesis and sufficient supply of ${SO_4}^{2-}$ to the sediment, stimulate the SRB(sulfate reducing bacteria) highly.

• Korean Journal of Environmental Biology
• /
• v.37 no.4
• /
• pp.568-578
• /
• 2019

The nymphal development of the potato aphid, Macrosiphum euphorbiae (Thomas), was studied at seven constant temperatures (12.5, 15.0, 17.5, 20.0, 22.5, 25.0, and 27.5±1℃), 65±5% relative humidity (RH), and 16:8 h light/dark photoperiods. The developmental investigation of M. euphorbiae was separated into two steps, the 1^st through 2^nd and the 3^rd through 4^th stages. The mortality was under 10% at six temperatures. However, it was 53.0% at 27.5℃. The developmental time of the entire nymph stage was 15.5 days at 15.0℃, 6.7 days at 25.0℃, and 9.7 days at 27.5℃. In the immature stage, the lower threshold temperature of the larvae was 2.6℃ and the thermal constant was 144.5 DD. In our analysis of the temperature-development experiment, the Logan-6 model equation was most appropriate for the non-linear regression models (r²=0.99). When the distribution completion model of each development stage of M. euphorbiae larvae was applied to the 2-parameter and 3-parameter Weibull functions, each of the model's goodness of fit was very similar (r²=0.92 and 0.93, respectively). The adult longevity decreased as the temperature increased but the total fecundity of the females at each temperature was highest at 20℃. The life table parameters were calculated using the whole lifespan periods of M. euphorbiae at the above six temperatures. The net reproduction rate (R₀) was highest at 20.0℃(63.2). The intrinsic rate of increase (r_m) was highest at 25℃(1.393). The finite rate of doubling time (D_t) was the shortest at 25.0℃(2.091). The finite rate of increase (λ) was also the highest at 25.0℃(1.393). The mean generation time(T) was the shortest at 25.0℃(9.929).

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.2
• /
• pp.153-160
• /
• 2009

A PM10 (aerodynamic diameter${\leq}$10 ${\mu}m$) sampler is used to quantify the potential human exposure to suspended particulate matter (PM) and to comply with the governmental regulation. This study was conducted to compare and evaluate the same PM10 cutpoint and different slopes between United States Environmental Protection Agency (USEPA) PM10 sampling criterion and American Conference of Governmental Industrial Hygienists/$Comit\acute{e}$ $Europ\acute{e}en$ de Normalization/International Organization for Standardization thoracic PM10 sampling criterion through theory and experiment. Four PM10 samplers according to the USEPA criterion and one RespiCon sampler in accordance with the thoracic PM10 criterion were used in the present study. In addition, one DustTrak monitor was used to measure real time PM10 mass concentrations. All six aerosol samplers were tested in a PM generation chamber using polydisperse fly ash. Theoretical mass concentrations were calculated by applying the measured particle size distribution characteristics (geometric mean = 6.6 ${\mu}m$, geometric standard deviation = 1.9) of fly ash to each sampling criterion. The measured mass concentrations through a chamber experiment were consistent with theoretical mass concentrations in that a RespiCon sampler with the thoracic PM10 criterion collected less PM than a PM10 sampler with the USEPA criterion. The overall chamber experiment results indicated, when a PM10 sampler was used as a reference sampler, that (1) a RespiCon sampler had a normalizing factor of 1.6, meaning that this sampler underestimated an average 60% of PM10 mass sampled from a PM10 sampler, and (2) a DustTrak real-time monitor using a PM10 inlet had a calibration factor of 2.1.

• Korean journal of applied entomology
• /
• v.42 no.1
• /
• pp.43-51
• /
• 2003

This study was carried out to develop the forecasting model of Pseudococcus comtocki Kuwana for timing spray. Field phonology and temperature-dependent development of p. comstocki were studied, and its stage transition models were developed. p comstocki occurred three generations a year in Suwon. The 1 st adults occurred during mid to late June, and the 2nd adults were abundant during mid to late August. The 3rd adults were observed after late October. The development times of each instar of p. comstocki decreased with increasing temperature up to 25$^{\circ}C$, and thereafter the development times increased. The estimated low-threshold temperatures were 14.5, 8.4, 10.2, 11.8, and 10.1$^{\circ}C$ for eggs, 1st+2nd nymphs, 3rd nymphs, preoviposition, and 1st nymphs to preoviposition, respectively. The degree-days (thermal constants) for completion of each instar development were 105 DD for egg,315 DD for 1st+2nd nymph, 143 DD for 3rd nymph, 143 DD for preoviposition, and 599 DD for 1 st nymph to preoviposition. The stage transition models of p. comstocki, which simulate the proportion of individuals shifted from a stage to the next stage, were constructed using the modified Sharpe and DeMichele model and the Weibull function. In field validation, degree-day models using mean-minus-base, sine wave, and rectangle method showed 2-3d, 1-7d, and 0-6 d deviation with actual data in predicting the peak oviposition time of the 1st and 2nd generation adults, respectively. The rate summation model, in which daily development rates estimated by biophysical model of Sharpe and DeMichele were accumulated, showed 1-2 d deviation with actual data at the same phonology predictions.

• Journal of Veterinary Clinics
• /
• v.29 no.3
• /
• pp.233-236
• /
• 2012

Cefquinome, a fourth generation cephalosporin, has been solely used for veterinary medicine and has a broad antibacterial spectrum against gram-negatives and gram-positives being very stable to ${\beta}$-lactamases. This study was conducted to evaluate the bioequivalence of two cefquinome 2.5% products in piglets. Plasma cefquinome concentrations were analyzed by liquid chromatography-mass spectrometry (LC/MS). Mean maximum concentration ($C_{max}$) of test product ($Cequus^{(R)}$) and reference product ($Cobactan^{(R)}$) were $4.34{\pm}0.58$ and $4.22{\pm}0.47{\mu}g/mL$, and mean area under the concentration time curve ($AUC_{0{\rightarrow}{\infty}}$) values were $10.43{\pm}1.96$ and $10.25{\pm}2.98{\mu}g{\cdot}h/mL$, respectively. The 90% confidence intervals for the ratio of $C_{max}$ (0.941-1.115), and $AUC_{0{\rightarrow}{\infty}}$ (0.927-1.172) values for the test and reference products were within the acceptable bioequivalence limit of 0.80-1.25. It is concluded that two commercial cefquinome injectable solutions are bioequivalent in their extent of drug absorption in piglets.

• Korean journal of applied entomology
• /
• v.46 no.1 s.145
• /
• pp.37-42
• /
• 2007

To construct a life table and development model Schizaphis graminum (Rondani), its adult longevity and fecundity were studied at various constant temperatures ranging from 15 to $32.5^{\circ}C$, with $65{\pm}5%$ RH, and a photoperiod of 16L:8D. Adult longevity of the greenbug gradually increased with decreasing temperature below $32.5^{\circ}C$. Total fecundity was not significantly different at all temperatures except at $32.5^{\circ}C$. Daily fecundity gradually increased from $25.0^{\circ}C$. It was 3.6 at $27.5^{\circ}C$ and as temperatures either went down or up, it decreased to 1.4 at $15.0^{\circ}C$ and 0.4 at $32.5^{\circ}C$ Net reproduction rate (Ro) was highest with 47.6 at $25.0^{\circ}C$. The intrinsic rate of increase per day $(r_m)$ and the finite rate of increase per day $({\lambda})$ were highest with 0.4 and 1.5 at $30.0^{\circ}C$, respectively and the doubling time (Dt) was shortest with 0.98 at $32.5^{\circ}C$. The mean generation time (T) was 8.41 at $30.0^{\circ}C$.

• Korean journal of applied entomology
• /
• v.53 no.4
• /
• pp.449-456
• /
• 2014

Life table analysis and temperature-dependent development experiments were conducted to understand the biological characteristics of the cabbage aphid, Brevicoryne brassicae (Linnaeus) on detached Tah Tsai Chinese cabbage (Brassica campestris var. narinosa) leaves at seven constant temperatures (15, 18, 21, 24, 27, 30 and $33{\pm}1^{\circ}C$; $65{\pm}5%$ RH; 16L:8D). Mortality was lowest at $24^{\circ}C$ with 18% and 0% at $1^{st}{\sim}2^{nd}$ and $3^{rd}{\sim}4^{th}$ nymphal stages, respectively. The developmental period of $1^{st}{\sim}2^{nd}$ nymphal stage was 8.4 days at $18^{\circ}C$, and it decreased with increasing temperature. The developmental period of the $3^{rd}{\sim}4^{th}$ nymphal stage was 6.7 days at $18^{\circ}C$. The lower threshold temperature calculated using a linear model was $7.8^{\circ}C$, and the effective accumulative temperature was 120.1DD. Adult longevity was 14.9 days at $21^{\circ}C$, and total fecundity was observed 58.5 at $24^{\circ}C$. According to the life table, the net reproduction rate was 47.5 at $24^{\circ}C$, and the intrinsic rate of increase and the finite rate of increase were 0.36 and 1.43, respectively, at $27^{\circ}C$. The doubling time was 1.95d at $27^{\circ}C$, and mean generation time was 7.43d at $30^{\circ}C$.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.3
• /
• pp.323-330
• /
• 2008

The study presents the results of 1,4-dioxane degradation using zero valent (Fe$^0$) or Fe$^{2+}$ ions with and without UV. During the reaction, the change of [Fe$^{2+}$] and [Fe$^{2+}$]/[Fe(t)], the concentration ratio of ferrous ion to total iron ion in solution was measured. Less than 10% degradation of 1,4-dioxane was observed by UV-only, Fe$^0$-only, and Fe$^{2+}$-only conditions, and also the changes of [Fe$^{2+}$] and [Fe$^{2+}$]/[Fe(t)] were minimal in each reaction. However, the oxidation of Fe$^0$ was enhanced with the irradiation of UV by approximately 25% and the improvement of 1,4-dioxane degradation was observed. Fenton reaction ($Fe^{2+}+H_2O_2$) showed higher degradation efficiency of 1,4-dioxane until 90 min, which of the degradation was stopped after that time. In the reaction of Fe$^{2+}$ and UV, the ratio of [Fe$^{2+}$]/[Fe(t)] decreased then slowly increased after a certain time indicating the reduction of Fe3+ to Fe$^{2+}$. In case of Fe$^0$ in the presence of UV, the first-order rate constant was found to be 1.84$\times$10$^{-3}$ min$^{-1}$ until 90 min, and then changed to 9.33$\times$10$^{-3}$ min$^{-1}$ when the oxidation of Fe$^{2+}$ mainly occurred. In this case [Fe$^{2+}$]/[Fe(t)] kept decreasing for the reaction. However, the addition of perchlortae (ClO$_4^-$) in the reaction of Fe$^0$ and UV induced the continuous increase of [Fe$^{2+}$]/[Fe(t)] ratio. The results mean the primary degradation factor of 1,4-dioxane is the oxidation by the radicals generated from the redox reaction between Fe$^{2+}$ and Fe$^{3+}$. Also, both UV and ClO$_4^-$ played the role inducing the reduction of Fe$^{3+}$, which is important to degrade 1,4-dioxane by enhancing the generation of radicals.

• Tuberculosis and Respiratory Diseases
• /
• v.40 no.4
• /
• pp.378-383
• /
• 1993

Background: In recent reports, it has been reported that increased coagulation and decreased fibrinolytic activity has been responsible for abnormal fibrin turnover in exudative pleural effusion. In the cases of empyema, the fibrinopurulent stage is characterized by the fibrin deposition resulting in formation of limiting membranes in the visceral and parietal pleura. Recently attention has been focused on intrapleural fibrinolytic therapy capable of removing intrapleural fibrin deposits by urokinase (UK) in the treatment of empyema. However, these clinical trials have provided the clinical evidences for resolution of pleural loculation after intrapleural urokinase injection (UK-injection), the profiles of fibrinolytic activity following the treatment were still not investigated. Therefore in order to demonstrate the fibrinolytic evidences behind the clinical efficacy of intracavitary UK-injection, we examined intrapleural plasminogen activator activity (PA-activity) and D-dimer (D-Di) concentrations before and after each repeated UK-injection into the pleura in subjects with loculated empyema cavity. Methods: In a group of 14 patients with multiple loculated empyema cavity, PA-activity and D-Di concentrations were measured before and after repeated UK-injection. One hundred thousand IU of UK was injected at each time and all sujects had at least two times of UK injection accoring to clinical decisions. Nine out of 14 sujects had three times of UK-injection. Results: The mean (${\pm}SE$) PA-activity prior to treatemnt was $10.5{\pm}7.0$ and it was increased to $91.9{\pm}27.0,\;432.3{\pm}177.1,\;170.0{\pm}85.3$ IU tPA/ml after first, second and third time of UK-injection respectively (p<0.01). D-Di concentrations were also increased from $4.16{\pm}1.06{\times}10^5$ to $9.62{\pm}1.54{\times}10^5,\;12.31{\pm}1.89{\times}10^5,\;8.54{\pm}1.56{\times}10^5$ ng/ml in the same order as above (p<0.05). Conclusion: The suppressed fibrinolytic activity in the empyema cavity get removed sinificantly after inrracavitary injection of urokinase by generation of additional intrapleural plasmin.