• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.12a
• /
• pp.53-57
• /
• 2006

In this paper, maxwell 3D finite element analysis program (Ansoft) was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 250 kHz and some specific conditions. The electromagnetic field in the ferrite core was shown to be high and symmetric. An LS-100 luminance meter and a Darsa-2000 spectrum analyzer were used in the experiment. According to data on the lamp tested using high magnetic field ferrite, the optical and thermal wave fields were shown to be high around the ring-shaped electrodeless fluorescent lamp. The optical or light field was high at the center of the bulb rather than around the ferrite core. The light conditions of the bulb were assumed to be complex, depending on the condition of the filler gas, the volume of the bulb, and the frequency of the inverter. Our results have shown coupling between the gas plasma and the field of the light emitted to be nonlinear.

• Journal of Magnetics
• /
• v.21 no.4
• /
• pp.652-659
• /
• 2016

In this study, the efficiencies for both the angular aligned and unaligned positions of the receiver and transmitter coils of wireless power transfer (WPT) systems are examined. Some parameters of the equivalent circuit were calculated with Maxwell 3D software. The analytical solution of the circuit was calculated in MATLAB program through the composition of the system's mathematical modeling. The numerical solution of the system, however, was calculated using PSIM, which is circuit simulation software. In addition, with the use of the finite element method (FEM) in Maxwell 3D software, transient analysis of the three-dimensional system was performed. The efficiency of the system was estimated through the calculation of input and output power. The results demonstrated that power was efficiently transmitted to a certain extent in aligned and unaligned positions. The results also revealed that, for aligned positions, high efficiency with air gaps of 15-20 cm can be obtained and that the efficiency quickly dropped with air gaps of more than 20 cm. For spatially unaligned positions, it was observed that wireless power transfer could be realized with high efficiency with air gaps of up to 10 cm and that efficiency quickly dropped with air gaps of more than 10 cm.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.6
• /
• pp.255-261
• /
• 2005

Recently, the RF inductive discharge or inductively coupled plasma continues to attract growing attention as an effective plasma source in many industrial applications, the best known of which are plasma processing and lighting technology. To the point of lighting sources, the ring-shaped electrodeless fluorescent lamps utilizing an inductively coupled plasma have been objects of interest and research during the last decades, mainly because of their potential for extremely long life, high lamp efficacies, rapid power switching response. In this paper, maxwell 3D finite element analysis program (Ansoft) was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 250 kHz and some specific conditions. The electromagnetic field in the ferrite core was shown to be high and symmetric. An LS-100 luminance meter and a Darsa-2000 spectrum analyzer were used in the experiment. According to data on the lamp tested using high magnetic field ferrite, the optical and thermal wave fields were shown to be high around the ring-shaped electrodeless fluorescent lamp. The optical or light field was high at the center of the bulb rather than around the ferrite core. The light conditions of the bulb were assumed to be complex, depending on the condition of the filler gas, the volume of the bulb, and the frequency of the inverter. Our results have shown coupling between the gas plasma and the field of the light emitted to be nonlinear.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.172-174
• /
• 1996

In this paper, the characteristics of single-phase induction motors is studied using TDFE(Time Domain Finite Element) analysis. The magnetic field equation from the Maxwell's equations is solved using 2-Dimensional TDFE method, and the circuit equations from the stator and rotor are solved simultaneously. The 3-D effects, which are the end-leakage reactance and the resistance of end-rings are considered in 2-D combined equations. The proposed method is applied to the commercial single-phase induction motor. The calculated waveforms of the currents shows a good agreement with the measured ones.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.93-99
• /
• 2016

The present study aims to increase the amount of surface flux by changing the magnetic directions of a spherical magnet (NdFeB) consisting of four poles. For this purpose, the magnetic directions of quartile spherical slices constituting the spherical magnet are manipulated and their three-dimensional analyses are carried out by using finite-element method via Maxwell environment. The analysis of the magnetic quartile spheres with four different magnetic directions are compared to the each other, and then the quartile sphere with the best surface flux distribution is suggested for rotor structure. It is clear emphasized that the induced torque of the spherical motor, in which such a rotor is used, will be improved as well.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2003.11a
• /
• pp.161-163
• /
• 2003

Ring-shaped electrodeless fluorescent lamp is removed the internal electrodes and heating filaments that are a light-limiting factor of conventional fluorescent lamps. The ring-shaped electrodeless lamp is intended as a high efficacy replacement for the incandescent reflector lamp in many applications. In this paper, maxwell 3D finite element analysis program (Ansoft) was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 250[㎑]and some specific conditions. The optical measurement measured luminance and a temperature and an optical spectrum distribution for 10 minutes in a one minute interval at the same time.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.3
• /
• pp.191-199
• /
• 2000

In this paper, a numerical analysis using the finite element method (FEM) is presented which models the eddy current testing (ECT) of tubes with 3-dimensional defects. For the description of 3-dimensional eddy current problems, the governing equation is derived from the Maxwell's equations. The 3-dimensional FEM formulation with hexahedral elements is carried out using the Galerkin weighted residual method. The INCONEL 600 steam generator tube with inner and outer diameter defects is adopted for the numerical analysis, and the ECT signal, which is the trajectory of the probe impedance, is calculated. For the verification of the numerical analysis method, results of numerical calculations and experiments are compared and they show good agreements. Based on this verification, several defect signals are predicted and their characteristics are investigated with the variation in the defect depth and the circumferential angle of the defect.

• Steel and Composite Structures
• /
• v.43 no.5
• /
• pp.533-552
• /
• 2022

The current article deals with the dynamic stability, and structural improvement of vibrating electrically curved screen on the viscoelastic substrate. By considering optimum value for radius curvature of the electrically curved screen, the structure improvement of the system occurs. For modeling the electrically system, the Maxwell's' equation is developed. Hertz contact model in employed to obtain contact forces between impactor and structure. Moreover, variational methods and nonlinear von Kármán model are used to derive boundary conditions (BCs) and nonlinear governing equations of the vibrating electrically curved screen. Galerkin and Multiple scales solution approach are coupled to solve the nonlinear set of governing equations of the vibrating electrically curved screen. Along with the analytical solution, 3D finite element simulation via ABAQUS package is provided with the aid of a FE package for simulating the current system's response. The results are categorized in 3 different sections. First, effects of geometrical and material parameters on the vibrational performance and stability of the curves panel. Second, physical properties of the impactor are taken in to account and their effect on the absorbed energy and velocity profile of the impactor are presented. Finally, effect of the radius and initial velocity on the mode shapes of the current structure is demonstrated.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.3
• /
• pp.208-213
• /
• 2012

With great advancement of the automobile functions, environmental factors become important performances, especially noise. This paper investigates noise sources of outer rotor type BLDC motor using in the air-conditioner of the automobiles. To this end, this paper is analyzed two viewpoints, structural and electromagnetic causes. Structural analysis is conducted through modal test and analysis. For modal analysis, 3D finite element analysis is carried out using commercial program ansys. Electromagnetic causes are analyzed from local force that is computed by Maxwell stress tensor method. Local force excites structure of motor directly. Finally, correlation analysis is performed to determine effect between noise causes.

• Proceedings of the KIEE Conference
• /
• 2008.04c
• /
• pp.245-246
• /
• 2008

In this paper we calculated and compared the arc driving force of two spiral-tyre vacuum interrupter electrode models which have 3petals and 4petals respectively by means of commercial finite element method software Maxwell 3D. As a result we can find that the more petals the electrode has, the stronger arc driving force was generated. This simulation method can contribute to optimization of spiral-type electrode designs in a view of arc driving force.