• Geomechanics and Engineering
• /
• 제24권5호
• /
• pp.431-441
• /
• 2021

Rock-socketed drilled shafts are widely used to transfer the heavy loads from the superstructure especially in mountainous area. Extensive research has been done on the behavior of rock-socketed drilled shafts under compressive load. However, little attention has been paid to uplift behavior of drilled shaft in rock, which govern the overall behavior of the foundation system. In this paper, a series of centrifuge tests have been performed to investigate the uplift response of rock-socketed drilled shafts. The pull-out tests of drilled shafts installed in layered rocks having various strengths were conducted. The load-displacement response, axial load distributions in the shaft and the unit skin friction distribution under pull-out loads were investigated. The effects of the strength of rock socket on the initial stiffness, ultimate capacity and mobilization of friction of the foundation, were also examined. The results indicated that characteristics of rock-socket has a significant influence on the uplift behavior of drilled shaft. Most of the applied uplift load were carried by socketed rock when the drilled shaft was installed in the sand over rock layer, whereas substantial load was carried by both upper and lower rock layers when the drilled shaft was completely socketed into layered rock. The pattern of mobilized shaft friction and point where the maximum unit shaft friction occurred were also found to be affected by the socket condition surrounding the drilled shaft.

• 한국운동역학회지
• /
• 제32권3호
• /
• pp.103-110
• /
• 2022

Objective: The aim of this study was to investigate effect of core stabilization exercises on the erector spinae contractile properties and trunk isokinetic muscle function of middle age with low physical activity and sedentary lifestyle. Method: Twenty (female: n=10, male: n=10) middle-age subjects (age: 37.25 ± 6.08 years, height: 168.01 ± 6.84 cm, weight: 71.37 ± 11.75 kg) participated in this study. Tensiomyography was measured on the erector spinae, and the isokinetic trunk muscle function test was measured at an angular velocity of 60 °/s and 90 °/s. All subjects performed the core stabilization exercises for 60 min per day, 3 times a week, for 7 weeks. A paired t-test was performed with a significance level of 0.05. Results: Tensiomyography of the erector spinae revealed a significant post-exercise increase in the maximum radial displacement (p < .05) and velocity of contraction (p < .05), however, there wasn't a significant post-exercise change in the contraction time. Additionally, the isokinetic muscle function test of the trunk revealed a significant post-exercise increase in trunk extensor relative strength (p < .05) and strength ratio (p < .05). Conclusion: Our results indicated that core stabilization exercises reduced erector spinae muscle stiffness, increased the velocity of erector spinae contraction. Additionally, data showed the improvement in the trunk extensor strength help induce a more balanced development in trunk muscle.

• Steel and Composite Structures
• /
• 제46권4호
• /
• pp.497-512
• /
• 2023

Using light weight concrete as infill material in conventional cold-formed steel (CFS) shear wall systems can considerably increase their load bearing capacity, ductility, integrity and fire resistance. The compressive strength of the filler concrete is a key factor affecting the structural behaviour of the composite wall systems, and therefore, achieving maximum compressive strength in lightweight concrete while maintaining its lightweight properties is of significant importance. In this study a new type of optimum polystyrene lightweight concrete (OPLC) with high compressive strength is developed for infill material in composite CFS shear wall systems. To study the seismic behaviour of the OPLC-filled CFS shear wall systems, two full scale wall specimens are tested under cyclic loading condition. The effects of OPLC on load-bearing capacity, failure mode, ductility, energy dissipation capacity, and stiffness degradation of the walls are investigated. It is shown that the use of OPLC as infill in CFS shear walls can considerably improve their seismic performance by: (i) preventing the premature buckling of the stud members, and (ii) changing the dominant failure mode from brittle to ductile thanks to the bond-slip behaviour between OPLC and CFS studs. It is also shown that the design equations proposed by EC8 and ACI 318-14 standards overestimate the shear force capacity of OPLC-filled CFS shear wall systems by up to 80%. This shows it is necessary to propose methods with higher efficiency to predict the capacity of these systems for practical applications.

• Geomechanics and Engineering
• /
• 제32권5호
• /
• pp.483-494
• /
• 2023

High-speed trains became common nowadays due to the need for fast and safe mean to transport goods and people. However, the use of high-speed trains necessitates the examination of the critical speed, which is the train speed at which the maximum settlement of the railway track occurs. The critical speed and railway track settlement have been investigated considering only one train in previous studies. However, it is normal to have two adjacent trains moving at the same time. This paper aims to understand how the interference of two moving trains affects the settlement and critical speed of ballasted railway track. Calibrated three-dimensional finite element models of railway track subjected to one moving train and two moving trains have been developed to address the aim of the study. It is found that the interference dramatically increases the railway track settlement with a percentage increase ranges between 5 and 100%. It is also found that the percentage increase of the railway track settlement depends on the train speed and the distance between the moving trains. In addition, it is found that the thickness of the ballast layer and the stiffness of the subgrade have minor influence on the percentage increase of the settlement. Importantly, the results of this paper illustrate the importance of the interference of the moving trains on the dynamic response of the railway track. Thus, there is a need to consider the dynamic interaction between the adjacent moving trains in the design of railway track foundation.

• Structural Engineering and Mechanics
• /
• 제87권6호
• /
• pp.529-540
• /
• 2023

A novel laminated-hybrid-composite-beam (LHCB) of glass-epoxy infused with flyash and graphene is constructed for this study. The conventional mixture-rule and constitutive-relationship are modified to incorporate filler and lamina orientation. Eringen's non-local-theory is used to include the filler effect. Hamilton's principle based on fifth-order-layer-wise-shear-deformation-theory is applied to formulate the equation of motion. The analogous shear-spring-models for LHCB with multiple-cracks are employed in finite-element-analysis (FEA). Modal-experimentations are conducted (B&K-analyser) and the findings are compared with theoretical and FEA results. In terms of dimensionless relative-natural-frequencies (RNF), the dynamic-response in cantilevered support is investigated for various relative-crack-severities (RCSs) and relative-crack-positions (RCPs). The increase of RCS increases local-flexibility in LHCB thus reductions in RNFs are observed. RCP is found to play an important role, cracks present near the end-support cause an abrupt drop in RNFs. Further, multiple cracks are observed to enhance the nonlinearity of LHCB strength. Introduction of the first to third crack in an intact LHCB results drop of RNFs by 8%, 10%, and 11.5% correspondingly. Also, it is demonstrated that the RNF varies because of the lamina-orientation, and filler addition. For 0° lamina-orientation the RNF is maximum. Similarly, it is studied that the addition of graphene reduces weight and increases the stiffness of LHCB in contrast to the addition of flyash. Additionally, the response of LHCB to moving mass is accessed by appropriately modifying the numerical programs, and it is noted that the successive introduction of the first to ninth crack results in an approximately 40% to 120% increase in the dynamic-amplitude-ratio.

• 한국지진공학회논문집
• /
• 제27권1호
• /
• pp.37-47
• /
• 2023

A new clamped mechanical splice system was proposed to develop structural performance and constructability for precast concrete connections. The proposed mechanical splice resists external loading immediately after the engagement. The mechanical splices applicable for both large-scale rebars for plants and small-scale rebars for buildings were developed with the same design concept. Quasi-static lateral cyclic loading tests were conducted with reinforced and precast concrete members to verify the seismic performance. Also, shaking table tests with three types of seismic wave excitation, 1) random wave with white noise, 2) the 2016 Gyeongju earthquake, and 3) the 1999 Chi-Chi earthquake, were conducted to confirm the dynamic performance. All tests were performed with real-scale concrete specimens. Sensors measured the lateral load, acceleration, displacement, crack pattern, and secant system stiffness, and energy dissipation was determined by lateral load-displacement relation. As a result, the precast specimen provided the emulative performance with RC. In the shaking table tests, PC frames' maximum acceleration and displacement response were amplified 1.57 - 2.85 and 2.20 - 2.92 times compared to the ground motions. The precast specimens utilizing clamped mechanical splice showed ductile behavior with energy dissipation capacity against strong motion earthquakes.

• Architectural research
• /
• 제25권1호
• /
• pp.1-9
• /
• 2023

Structural ageing influences the structural performance in a negative way by reducing the seismic resilience of the structure which makes it a major concern around the world. Retrofitting is considered to be a pragmatic and feasible solution to address this issue. Numerous retrofitting techniques are devised by researchers over the years. The viability of using steel bracings as retrofitting component is evaluated on a G+30 storied building model designed according to ACI318-14 and ASCE 7-16. Four different types of steel bracing arrangements (V, Inverted V/ Chevron, Cross/ X, Diagonal) are assessed in the model developed in commercial nu-merical analysis software while considering both material and geometric nonlinearities. Reducing displacement and cost in the structures indicates that the design is safe and economical. Therefore, the purpose of this article is to find the best bracing system that causes minimum displacement, which indicates maximum lateral stiffness. To evaluate the seismic vulnerability of each system, incremental dynamic analysis was conducted to develop fragility curves, followed by the formation of collapse margin ratio (CMR) as stipulated in FEMA P695 and finally, a cost estimation was made for each system. The outcomes revealed that the effects of ge-ometric nonlinearity tend to evoke hazardous consequences if not considered in the structural design. Probabilistic seismic and economic probes indicated the superior performance of V braced frame system and its competency to be a germane technique for retrofitting.

• 한국지반공학회논문집
• /
• 제26권8호
• /
• pp.67-75
• /
• 2010

본 연구에서는 연약 점성토 지반에 근입된 모형말뚝을 대상으로 다양한 입력 가속도 크기 및 진동수 조건에서 1g 진동대 실험을 수행하였다. 실험 결과를 이용하여, 각각의 동적 p-y 곡선을 산정하였으며, 이 p-y 곡선 상에서 최대지반반력이 나타나는 꼭지점들을 연결하여 연약 점성토의 동적 p-y 중추곡선(Backbone curve)을 쌍곡선 함수로 나타내었다. 이 쌍곡선 함수를 정의하는데 필요한 초기 기울기와 극한 저항력은 Matlock의 p-y 곡선 공식을 이용하여 제안하였다. 새로 제안한 동적 p-y 중추곡선은 실제 내진설계에 사용되고 있는 정적 p-y 곡선과 다른 연구자들의 원심모형실험 결과 및 수치해석 결과와 비교하여 검증하였다.

• 대한토목학회논문집
• /
• 제30권3B호
• /
• pp.315-324
• /
• 2010

본 논문에서는 대규모 유탄성 해석을 통해 초대형 부유식 해상구조물의 설계 차트를 개발했다. 초기 설계단계에 본 챠트를 이용해서 고비용의 유탄성 해석을 사용하지 않고도 초대형 부유식 해상구조물의 유탄성 거동을 예측이 가능하다. 본 논문에서는 두 가지 종류의 설계챠트 I, II을 개발하여 제시하였다. 설계차트 I은 특정 주파수의 파랑에 대한 구조물의 최대응력 응답진폭함수를 얻을 수 있도록 개발되었다. 설계차트 I의 경우 동일한 변장비와 무차원 구조강성계수를 갖는 모든 구조물에 적용이 가능하다. 설계챠트 I과 파랑스펙트럼의 적분을 통해 설계차트 II를 개발하였으며, Beaufort 풍력급에 따른 Bretschneider 스펙트럼을 적용해 해상의 환경요인을 고려하도록 구성되었다.

• Steel and Composite Structures
• /
• 제46권6호
• /
• pp.793-804
• /
• 2023

In this study, cyclic loading tests were conducted to assess the seismic performance of cast-in-place (CIP) concrete-filled hollow core precast concrete columns (HPCC) constructed using steel ducts and rubber tubes. The outer shells of HPCC, with a hollow ratio of 47%, were fabricated using steel ducts and rubber tubes, respectively. Two combinations of shear studs & long threaded bars or cross-deformed bars & V-ties were employed to ensure the structural integrity of the old concrete (outer shell) and new CIP concrete. Up to a drift ratio of 3.8%, the hysteresis loop, yielding stiffness, dissipated energy, and equivalent damping ratio of the HPCC specimens were largely comparable to those of the solid columns. Besides the similarities in cyclic load-displacement responses, the strain history of the longitudinal bars and the transverse confinement of the three specimens also exhibited similar patterns. The measured maximum moment exceeded the predicted moment according to ACI 318 by more than 1.03 times. However, the load reduction of the HPCC specimen after reaching peak strength was marginally greater than that of the solid specimen. The energy dissipation and equivalent damping ratios of the HPCC specimens were 20% and 25% lower than those of the solid specimen, respectively. Taking into account the overall results, the structural behavior of HPCC specimens fabricated using steel ducts and rubber tubes is deemed comparable to that of solid columns. Furthermore, it was confirmed that the two combinations for securing structural integrity functioned as expected, and that rubber air-tubes can be effectively used to create well-shaped hollow sections.