• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2002.09a
• /
• pp.28-34
• /
• 2002

The b-value in the magnitude-frequency relationship logN(m) = $\alpha$ - bmwhere N(m) is the number of earthquakes exceeding magnitude m, is important seismicity parameter In hazard analysis. Estimation of the b-value for earthquake data observed on KSRS array network is done employing the maximum likelihood technique. Assuming the whole Korea Peninsula as a single seismic source area, the b-value is computed at 0.9. The estimation for KMA earthquake data is also similar to that. Since estimate is a function of minimum magnitude, we can inspect the completeness of earthquake catalog in the fitting process of b-value. KSRS and KMA data lists are probably incomplete for magnitudes less than 2.0 and 3.0, respectively. Examples from probabilistic seismic hazard assessment calculated for a range of b-value show that the small change of b-value has seriously effect on the prediction of ground motion.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.1
• /
• pp.123-131
• /
• 2005

In this research, shaking table tests for three types of gravity quay wall system were performed to analyze the influence of excess pore pressure in backfill soils on the natural frequency of gravity quay wall systems. The elastic modulus of backfill soils was also estimated from the back analyses using the results of the shaking table tests. From the test results, it was observed that as the magnitude of excess pore pressures increased, the natural frequency of the gravity quay wall system decreased and vice versa. The natural frequency was about 44Hz when no excess pore pressure was generated in backfill soils, and decreased to about 16Hz at the pore pressure ratio of 0.55. The elastic modulus of backfill soils reached the constant maximum value when the pore pressure ratio was less than 0.2, and abruptly decreased as the pore pressure ratio became larger than that. The elastic modulus of backfill soils decreased to $10\%$ of the maximum value when the pore pressure ratio was 0.55.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.646-653
• /
• 2001

LQG/LTR Control Methology is recently used for the analysis of multi-variable control in frequency domain. Target filter loop is designed by the demanding requirements such as cross-over frequency, disturbance rejection in low frequency domain, zero steady-state error, identification of maximum and minimum singular values and sensor noise rejection in high frequency domain. Loop transfer recovery is accomplished by solving the cheap control and then simulation close to the target filter loop. In this study, LQG/LTR Control Methodology is applied to the seat suspension system. It is found that this technique is very effective to control the system and improve the ride quality of human body.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.3
• /
• pp.436-442
• /
• 2022

In this paper, the performance of the selective combining according to the channel selection decision method of frequency diversity is evaluated in the underwater frequency selective channel. The underwater acoustic channel in the shallow sea has a complex multipath characteristic by combining various environmental factors such as boundary surface reflection and sound wave refraction according to the water temperature layer. In particular, frequency selectivity due to multipath causes energy fluctuation in a communication channel, which reduces SNR (Signal to Noise Ratio) and deteriorates communication performance. In this paper, we applied the frequency diversity technique using multiple channels to secure the communication performance according to the frequency selectivity by multipath. For each channel, 4-FSK (Frequency Shift Keying) and selective combining were applied, the performance was evaluated by applying the maximum value, average value, and majority decision of the signal in order to decide the demodulation channel selection of the selective combining.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.21 no.1
• /
• pp.21-34
• /
• 1984

This paper is concerned with the experimental investigation of transverse vibration characteristics in water of rectangular plates having an inner free cutout. Systematic experiments are carried out to investigate effects of the surrounding water on the added mass and the natural frequency of the plates due to the changes of the aspect ratio, hole size and eccentricity. The main subject is the clamped rectangular plate with a circular hole. For the purpose of comparative evaluations, some other common-type boundary conditions and hole shapes such as ellipses and rectangles are also investigated. Some of the results obtain are as follows; 1) For each given aspect ratio of the plate, there is a hole area ratio which gives a minimum value of the nondimensional frequency parameter for each mode. The hole area ratio increases as the order number of the mode increases. 2) The nondimensinal mass-increment parameter decreases as the aspect ration or the order number of the mode increases. For each given aspect ratio, the parameter the fundamental mode decreases monotonically as the hole area ratio increase. In cases of the second and higher order modes, however, each mode has a hole area ratio which gives a maximum value of the parameter for each aspect ratio more then 2/3. 3) Comparing elliptic holes with rectangular ones with same hole area ratio, nondimensional frequency parameters are almost same for each given ratio of the shorter axises to the longer one. 4) The influences of difference in boundary condion on nondimensional frequency parameters in water are similar to those in air.

• Journal of Advanced Navigation Technology
• /
• v.14 no.2
• /
• pp.176-182
• /
• 2010

This paper proposes that an inverse class-E amplifier is used a tunable parallel resonator at output port in order to maintain a high power-added efficiency(PAE) and output power with wide frequency ranges. A tunable circuit has a constant Q factor at operating frequency ranges and because of using varactor diode, the inductor and capacitor values of resonator can be changed. Also, the inductance value for zero-current switching (ZCS) is implemented a lumped element and the capacitance value is made a distributed element for phase compensation. The inverse class E amplifier using tunable parallel resonator is obtained to deliver 25dBm output power and achieve maximum power added efficiency(PAE) of 75% at 65-120MHz frequency ranges.

• Korean Journal of Optics and Photonics
• /
• v.30 no.2
• /
• pp.48-58
• /
• 2019

We investigate the signal-to-noise ratios (SNRs) of time-domain (i.e. pulsed illumination) and frequency-domain (i.e. chirped illumination) photoacoustic signals measured by a spherically focused ultrasound transducer for spherical absorbers. The simulation results show that the time-domain photoacoustic SNR is higher than that of frequency-domain photoacoustic signals, as reported in the previous literature. We understand the reason for this SNR gap between the two measurement modes by analyzing photoacoustic-signal spectra, considering the incident beam energy controlled by the maximum permissible exposure. As the result of this approach, we find that filtering off the DC term in the chirped signal's spectrum improves frequency-domain photoacoustic SNRs by up to approximately 5 dB. In particular, it is observed that photoacoustic SNRs are highly sensitive to an upper-frequency value of frequency filtering functions, and the optimal upper-frequency values maximizing the SNR are different in time- and frequency-domain photoacoustic measurements.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.710-715
• /
• 1997

This paper deals with the analysis of the optimum value of honeycomb core considering variable design parameter. As thickness and height of core rises in design parameter, natural frequency of laminated composite plate increases. The angle-phy has the maximum value when the plate of honeycomb core join to opposite direction. This paper shows that the natural frequency of CFRP was higher than that of GFRP and mode shapes were various at angle-ply.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.2
• /
• pp.43-50
• /
• 1986

Numerical analysis has been made on the dynamic behavior of an elastically supported beam subjected to an axial force and solid viscosity when the frequency of external force passes through the first critical frequency of the beam. Within the Euler-Bernoulli beam theory the solutions are obtained by using finite Fourier sine transform and Laplace transformation methods with respect to space and time variables. Integrations involved in the theoretical results are carried out by Simpson's numerical integration rule. The result shows that the maximum value of the dynamic deflection are much affected by the value of a solid viscosity, an axial force, an elastic constant and ratio of .omega.$_{max}$/.omega.$_{1}$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.10
• /
• pp.887-894
• /
• 2000

In this paper, we have studied the effect of earth (Gd, Er) on the various properties (microstructure, shrinkage, initial permeability, permeability as a function of frequency, etc) of Ba-ferrite. The permeabilities were analyzed by Impedance Analyzer(100KHz~40MHz) and Network Analyzer(30KHz~3㎓). As the result of XRD, all of the Ba-ferrite doped with rat earth was found to be Y-hexagonal phase. The resonance frequencies at the maximum imaginary value of complex permeability were observed near 2㎓. The complex permeabilities of the Ba-ferrite doped with Gd$_2$O$_3$at 3wt% and doped with Er$_2$O$_3$at 3wt% and 5wt% as a function of frequency showed the highest value at sintered temperature at 95$0^{\circ}C$/3h.