• International Journal of Highway Engineering
• /
• v.19 no.6
• /
• pp.191-199
• /
• 2017

PURPOSES : The objective of this study is to develop a methodology to estimate the minimum required separation distance (MRSD) between a vehicle and a bicycle when overtaking. METHODS : Three steps have been conducted to develop a methodology to estimate MSRD. First, a literature review has been conducted on the measurement of MSRD, and how it may be applied in Korea. Second, two assumptions have been made to develop a methodology to estimate the MSRD. The first assumption is that the maximum separation distance between a vehicle and a bicycle can be observed when they are at the same location longitudinally. In addition, it is assumed that the separation distance is invalid when the contra-flow exists. Finally, three cameras were installed at a height of 10 m to record the vehicle-bicycle interaction. Moreover, the vehicle trajectories as well as the separation distance were coded and analyzed. Through the hypothesis test and the interval estimation, the sample mean was tested and the confidence interval was estimated. RESULTS : 141 records of separation distance data were collected, and the hypothesis test demonstrated that the MSRD in Korea is significantly higher than other countries. In addition, the confidence interval of the population mean of MSRD is from 1.51 m to 1.65 m with 95% level of confidence. CONCLUSIONS : It is expected that the proposed methodology to estimate MSRD would be beneficial in studying road safety of vehicles and bicycles. Also, the proposed MSRD is expected to be designated in the act of road and transportation.

• Journal of the Regional Association of Architectural Institute of Korea
• /
• v.20 no.6
• /
• pp.47-54
• /
• 2018

The purpose of this study is to verify the long - range measurement performance for practical field application of VDMS. The reliability of the VDMS was verified by comparison with the existing monitoring sensor, GPS, Accelerometer and LDS. It showed the ability to accurately measure the dynamic displacement by tracking a motion of free vibration of target. And using the PSD function of measured data, the results in the frequency domain were also analyzed. We judged that VDMS is able to identify the higher system mode and has sufficient reliability. Based on the reliability verification, we conducted tests for long-distance applicability for actual application of VDMS. The distance from the stationary target model structure was increased by 50m interval, and the maximum distance was set to 400m. From the distance of 150m, the image obtained by the commercial camcorder has an error in the analysis, so the measured displacement comparison was performed between the LDS and the refractor telescope measurement results. In the measurement results of the displacement area of VDMS, the data validity was deteriorated due to the data shift by the external force and the quality degradation of the enlarged image. However, even under the condition that the effectiveness of the displacement measurement data of VDMS is low, the first mode characteristic included in the free vibration of the object is clearly measured. If the influence from the external environment is controlled and stable data is collected, It is judged that reliability of long-distance VDMS can be secured.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2002.03a
• /
• pp.42-50
• /
• 2002

The duration and H/V ratio(the amplitude ratio of the horizontal to vertical components) of ground motions caused by earthquakes in southern Korea are analyzed. Total 329 seismograms of horizontal component recorded at hypocentral distances of 10 to 350 km from 27 earthquakes with local magnitude 2 to 4 are used for the analysis. Simplified relation between the duration of ground motion( $T_{d}$) and the ratio($\chi$) of Arias intensity( $I_{A}$) and squared maximum acceleration($\alpha$$_{max}$$^{2}$) is determined to be $T_{d}$ = 3.423$\chi$$^2$+ 8.200$\chi$ + 0.029, which is useful for the estimation of the duration in southern Korea. There are three distinct distance ranges with different linear variations of the duration in hypocentral distance. They are distance intervals of 10~80km, 80~140km, and the distance greater than 140km. The duration in southern Korea shows clear proportionality to the local magnitude at magnitudes greater than 3.1. The value 1.37 of the H/V ratio obtained in southern Korea is similar to the value 1.4 of ENA(Eastern North America). The H/V ratio in southern Korea increases in the frequency range from 0.3 to 10Hz. The duration and H/V ratio of ground motions derived in this study could be used in the stochastic simulation of strong ground motion.ion.n.n.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.113-113
• /
• 2014

This study has been conducted for evaluation of qualitative/quantitative risk of HCNG filling station. In case of fire explosion occurred because of hydrogen, CNG, and HCNG leaking on same conditions, maximum overpressure was measured as 30kPa for hydrogen, 3.5kPa for HCNG, and 0.4kPa for CNG. The overpressure of HCNG was measured 7.75 times higher than that of CNG, but it was only 11.7% compared with hydrogen. When the explosion was occurred, in case of hydrogen, the measured influential distance of overpressure was 59m and radiant heat was 75m. In case of CNG, influential distance of overpressure was 89m and radiant heat was 144m would be estimated. In case of 30% HCNG that was blended with hydrogen and CNG, influential distance of overpressure was 81m and radiant heat was 130m were measured. As the explosion occurred with the same sized container that had 350bar for hydrogen and 250bar of CNG and HCNG, the damage distance that explosive overpressure and radiant heat influenced CNG was seen as the highest. HCNG that was placed between CNG and hydrogen tended to be seen as more similar with CNG.

• Journal of Biosystems Engineering
• /
• v.32 no.3
• /
• pp.145-152
• /
• 2007

Uniformity of spray deposit is one of the important factors in spray performance affecting efficacy of pest management. Distributions of spray deposit on artificial targets were measured and analyzed to enhance the efficiency of spray application. The research was studied to understand the deposition characteristics of spray droplets and to determine the optimum conditions of chemical application. The deposit and its pattern by the lower fan speed was more uniform and higher than that by the higher fan speed. The upward blasting distance was limited within 3 m, but the limit to the ground level was expanded the distance more than 3.5 m because of the accumulated droplets. When the fan speed was higher at the distance of 2.5 m, deposit reached to maximum. When the distance increased, deposit was getting lower. At the both fan speeds, the deposit was concentrated below $30^{\circ}$ because of the gravitation and the resistance of wind. This research can be useful in designing an orchard sprayer and its operation for various tree canopies. To achieve a uniform distribution of deposit using the air-blast type orchard sprayer, the application rate from the middle boom should be increased as the air velocity to the upward increased. The spray rate to the side boom should be limited in a minimal level.

• Journal of the Korean Institute of Gas
• /
• v.1 no.1
• /
• pp.73-80
• /
• 1997

This study was performed to develop the dispersion modeling methodology for quantitative prediction of the hazard distance or toxic buffer distance by comparing 10-min average, 30-min average, and 1-hr average maximum ground-level concentration with $Cl_2$ regultaion concentration, IDLH and ERPG-3 concentration for hazardous toxic gas, $Cl_2$ releases from the storage tank of the chemical plant facilities. For this dispersion modeling, the source term model, dispersion model, meteorological and topographical data are incorporated into the SuperChems model, and then the effects of the atmospheric stability, wind speed, and surface roughness length changes on the maxum ground-level concentration were estimated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.4
• /
• pp.1395-1405
• /
• 1996

The purpose of this experimental research is to investigate the local heat transfer characteristics in the upward free water jet impinged on a downward flat plate of uniform heat flux. The inner shape of rectangular nozzle used was sine curve type and its contraction ratio of inlet to outlet area was five. Experimental parameters considered were Reynolds number, nozzle exit-flat plate distance, and level of supplementary water. Local Nusselt number was influenced by Reynolds number, Prandtl number, supplementary water level, and distance between the nozzle exit and flat plate. Within the impingement region, the Nusselt number has a maximum value on the nozzle center axis and decreases monotonically outward from center. Outside of the impingement region, on the other hand, the Nusselt number has a secondary peak near the position where the distance from nozzle center reaches four times the nozzle width. However if nozzle exit velocity exceeds 6.2 m/s, the secondary peak appears also in the impingement region. The empirical equation for the stagnation heat transfer is a function of Prandtl, Reynolds, and axial distance from the nozzle exit. The optimum level of supplementary water to augment the heat transfer rate at stagnation point was found to be twice the nozzle width.

• Korean Journal of Environmental Biology
• /
• v.38 no.1
• /
• pp.106-113
• /
• 2020

This study identified the differences in the morphometric characteristics of the truss and classical dimensions between diploid and triploid Far Eastern catfish, Silurus asotus, and provided methods for sorting diploid and triploid Far Eastern catfish based on morphometric observations. The significant variables were the direct distance between the anterior edge of the lower lip and the anterior insertion of the dorsal fin(DALAD), the horizontal distance between the anterior edge of the lower lip and the anterior insertion of the ventral fin (HALAV), the direct distance between the anterior edge of the upper lip and the first nostril(DAUF), the direct distance between the anterior edge of the upper lip and the second nostril(DAUS), the interorbital width(IW), and the mandible barbel length (ManBL). The more significant variables were HALAV, DALAD, DAUF, IW, and DAUS. The most useful combination of variables for separating the two groups was DALAD, IW, and DAUF, which correctly classified 85% of the catfish as triploid or diploid, and that percentage was the maximum degree of value possible (p<0.05). Triploid Far Eastern catfish had a high rate of growth in the head region and body depth during the first year after hatching. Triploid Far Eastern catfish had smaller heads and shorter mandible barbels than diploid Far Eastern catfish.

• Journal of Communications and Networks
• /
• v.17 no.6
• /
• pp.634-646
• /
• 2015

Assuming perfect channel state information (CSI) at the transmitter and receiver, the optimization problem of maximizing the minimum Euclidean distance between two received signals by a linear precoder is considered for multiple-input multiple-output (MIMO) systems with arbitrary dimensions and arbitraryary quadrature amplitude modulation (QAM) input. A general precoding framework is first presented based on the Gram matrix, which is shown for 2-dimensional (2-D) and 3-dimensional (3-D) MIMO systems when employing the ellipse expanding method (EEM). An extended precoder for high-dimensional MIMO system is proposed following the precoding framework, where the Gram matrix for high-dimensional precoding matrix can be generated through those chosen from 2-D and 3-D results in association with a permutation matrix. A complexity-reduced maximum likelihood detector is also obtained according to the special structure of the proposed precoder. The analytical and numerical results indicate that the proposed precoder outperforms the other precoding schemes in terms of both minimum distance and bit error rate (BER).

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.6
• /
• pp.855-860
• /
• 1999

An experimental study of jet impingement on the surface with linear temperature gradient is conducted with the presentation of the turbulent characteristics and the heat transfer rates measured when this jet impinges normally to a flat plate. The jet Reynolds number ranges from 30,000 to 90,000, the temperature gradient of the plate is 2~$4.2^{\circ}C$/cm and the dimensionless nozzle to plate distance(H/D) is from 6 to 10. The results show that the peak of heat transfer rate occurs at the stagnation point, and the heat transfer rate decreases as the radial distance from the stagnation point increases. A remarkable feature of the heat transfer rate is the existence of the second peak. This is due to the turbulent development of the wall jet. Maximum heat transfer rate occurs when the axial distance from the nozzle to nozzle diameter(H/D) is 8. The heat transfer rate can be correlated as a power function of Prandtl number, Reynolds number and the dimensionless nozzle to plate distance(H/D). It has been found that the heat transfer rate increases with increasing turbulent intensity.