• 한국화재소방학회논문지
• /
• 제29권2호
• /
• pp.33-38
• /
• 2015

고압과 정량 흡상을 목적으로 클리어런스가 없는 초고압 회전용적형 헬리컬기어 펌프의 개발을 진행하였다. 펌프의 내부 압력과 토출 유속을 검증하기 위해 CFD 해석을 수행하였다. 이에 따라 FVM 기법으로 유동해석을 수행하였는데 클리어런스가 없는 완전히 밀폐된 형태의 FVM 유동해석은 격자가 연속하게 구성되지 않아 유체영역이 분리되어 정상적인 결과를 얻어낼 수 없었다. 이러한 문제로 격자 구성이 필요치 않은 MPS 기법으로 유동해석을 수행하였고, MPS 유동해석을 통해 펌프의 내부 압력과 토출 유속을 확인할 수 있었다. 로터의 회전속도 1,000 rpm에서 펌프 내부의 압력은 최소일 때 19.5 bar, 최대일 때 44.6 bar이고, 평균 압력은 33.9 bar로 확인되었다. 토출 유속은 최소일 때 64.5 m/s, 최대일 때 84.8 m/s이고, 평균 유속은 76.1 m/s로 확인되었다. 본 연구를 통해 클리어런스가 없는 해석 모델의 유동해석은 FVM 기법보다는 MPS 기법이 더 적합하였음을 확인할 수 있었다. 또한 초고압 회전 용적형 헬리컬기어 펌프의 압력의 변화에 따른 유속과의 관계를 본 연구를 통해 규명할 수 있었다.

• 한국해양공학회지
• /
• 제28권6호
• /
• pp.500-507
• /
• 2014

This study aimed at conducting a flow analysis of the pressure distribution, discharge flow rate, and consequent thrust force according to the rotational speed of a three-dimensional screw propeller, and then investigating the effect of the rotational speed on the characteristics of the screw propeller by varying the relevant speed (3200, 2400, 1600, 800 rpm). In particular, the computational domain was considered by the analysis in the blades and outlet chamber, using boundary conditions. The difference between the minimum and maximum pressures was 5.5 MPa under the given conditions. The discharge flow rate at this pressure difference was on the level of 1956.67 kg/s, as a thrust force of 47083.7 T(N) was obtained. This study showed that the discharge flow rate linearly increased with the rotational speed, proportional to the RPM, while the thrust force was gradually and steadily increased with the relevant speed. In addition, it was proved that the occurrence of cavitation under the given conditions was closely related to the decrease in the durability of the screw propeller because the thrust force depends on the speed.

• 한국전기전자재료학회논문지
• /
• 제16권10호
• /
• pp.902-907
• /
• 2003

In this paper, the ITO thin film, which is considered as one of the most currently used material for the high performance transparent conducting films for the PDP cell, was made in a parallel-plate, capacitively coupled DC magnetron sputtering system. Some electrical and optical properties of ITO films were investigated and discussed on the basis of glow discharge characteristics. The optimized thin film fabricating conditions of Ar gas pressure and substrate temperature were derived from the Paschen curve and glow discharge characteristics. The maximum transmittance of 89.61 % in the visible region and optical band gap of 3.89 eV and resistivity of 1.67${\times}$10$\^$-3/ $\Omega$-cm were obtained under the conditions of 300 C of substrate temperature and 10∼15 mtorr of pressure, which corresponds nearly to that of Paschen minimum.

• 전기의세계
• /
• 제17권3호
• /
• pp.39-42
• /
• 1968

We have been studying on the discharged phenomena if compound dielectrics for insulator which is very important in electric machinery and et al. In this paper we come to the couclusion that as a result of studying on the electric design of Ozonizer, the higher frequency becomes the better output could be got, and then discharge power could be the greatest by selecting the distance of the discharge gap and atomospheric pressure properly under the same applied voltage, and that power factor of the Ozonizer reached the maximum power at a particular frequency when the discharge power is maintained at constant.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.163-170
• /
• 2008

Auxiliary port which had been known to be used to reduce the expansion loss of a refrigeration system was applied to a R134a reciprocating compressor in a household refrigerator cycle with an intention of improving the compressor performance. Effects of the auxiliary port on the compressor performance was investigated by a computer simulation program. When a simple hole was made on the side wall of the cylinder as an auxiliary port and surrounding gas inside the compressor shell was assumed to be drawn into the cylinder through the hole, maximum COP improvement of 1.66% was obtained. With auxiliary port equipped with a plate type of check valve, maximum COP was raised to be 1.99%. COP improvement was more distinctive with decreasing the discharge pressure; COP improvement was 5% with discharge pressure of 7 bar.

• 설비공학논문집
• /
• 제20권10호
• /
• pp.637-644
• /
• 2008

Auxiliary port which had been known to be used to reduce the expansion loss of a refrigeration system was applied to a R134a reciprocating compressor in a household refrigerator cycle with an intention of improving the compressor performance. Effects of the auxiliary port on the compressor performance was investigated by a computer simulation program. When a simple hole was made on the side wall of the cylinder as an auxiliary port and surrounding gas inside the compressor shell was assumed to be drawn into the cylinder through the hole, maximum COP improvement of 1.66% was obtained. With auxiliary port equipped with a plate type of check valve, maximum COP was raised to be 1.99%. COP improvement was more distinctive with decreasing the discharge pressure; COP improvement was 5% with discharge pressure of 7 bar.

• 한국안전학회지
• /
• 제15권4호
• /
• pp.95-100
• /
• 2000

This study was performed in Hartmann type dust explosion apparatus in order to research the dust explosion characteristics of hydroxypropyl methyl cellulose(HPMC): minimum explosive limit, minimum ignition energy, limiting oxygen concentration, maximum explosion pressure, rate of pressure rise, etc. The samples of HPMC dust were distributed into 120-140 mesh, 170-230 mesh and 325 under, and the gap distance of the discharge electrode was setted up at 5mm. The experimental results were obtained as follows: (1) The minimum explosive limit for HPMC dust was founded at 180g/㎥. the minimum ignition energy at 9.8mJ and the limiting oxygen concentration at 12%. (2) The maximum explosion pressure of HPMC dust was $8.1kg/cm^2\;{\cdot}\;$abs at the concentration of $500g/m^3$ and the maximum rate of pressure rise was 203.98 bar/sec at the concentration of $480g/m^3$ for 325 under.

• 한국화재소방학회논문지
• /
• 제26권5호
• /
• pp.85-91
• /
• 2012

소방차에 설치되는 소방펌프에 대한 방수성능 기준이 현장에서 운용하고 있는 실태와 상이한 부분이 있고, 기준이 명확하게 규정되어 있지 않아 소방공무원이 화재현장에서 소방펌프의 사용시간, 최대사용압력, 사용 호스 직경 등 사용 실태를 분석하고, 그 결과를 토대로 소방펌프에 대한 압력별, 호스 직경별 수량별로 다양하게 성능시험을 실시하였다. 현장조사 결과, 소방자동차용 소방펌프의 성능에 관한 인정기준에서 규정하고 있는 규격방수압력(0.85MPa)과 고압방수압력(1.4 MPa)보다 현장에서는 더 높은 압력을 사용하고 있는 것으로 조사되었다. 또한, 펌프의 성능시험 결과는 방수량 및 방수압력 등이 호스의 직경, 관창에 따라 현재 규정하고 있는 인정기준과 매우 상이하게 측정되었으며, 본 연구 결과로 새로운 규격을 제안한다.

• 한국유체기계학회 논문집
• /
• 제8권6호
• /
• pp.33-39
• /
• 2005

A thermal vapor compressor in which the subsonic/supersonic flow appears simultaneously, has been accurately designed through the CFD analysis for the various shape parameters such as the primary nozzle shape, converging duct shape, mixing tube diameter, and so on. The performance of the developed thermal vapor compressor has been experimentally verified to be installed in a Multi Effect Desalination(MED) plant as an important element. In this paper, the effects of each parameter are discussed on the basis of CFD results and the experimental results for various boundary conditions(motive pressure, suction pressure, and discharge pressure) are presented in compared with CFD results. The two results show a good agreement with each other within 2 % accuracy with regard to the entrainment ratio.

• 한국가스학회지
• /
• 제12권2호
• /
• pp.105-109
• /
• 2008

안전밸브는 정압기지 내에 정압기의 파괴 또는 관 내 수분의 응축 등으로 인한 관내 압력의 비정상적인 증가를 자동적으로 완화시켜주는 메커니즘을 가지고 있는 밸브이다. 따라서 정압기지의 안전을 위해서 안전밸브의 유동 특성과 유동 형태를 살펴보는 것은 매우 중요하다. 본 논문은 안전밸브의 분출용량과 필요분출면적에 따른 유동 특성을 수치해석을 통해서 분석하였다. 본 결과를 국내 외 안전밸브 관련 규정인 미국의 API(America Petroleum Institute), 유럽 연합의 EN(European Standard), 프랑스의 NF(Norme Francise)를 이용하여 분석, 비교하였다. 또한 안전밸브의 최대 필요 분출 면적을 이용하여 국내 및 국외 규정을 각각 적용하였을 때의 안전밸브의 필요 설치 수량에 대한 고찰을 해보았다.