• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1160-1169
• /
• 1999

In this study, the silane primers were introduced to improve the interface adhesion between copper and epoxy. Especially, the polymer types obtained by solution and emulsifier-free emulsion polymerization of vinyltriethoxysilane and the low molecular weight types of 3-aminopropyltriethoxysilane(3-APTES) and 3-glycidoxypropyltrimethoxysilane(3-GPTMS) were used to improve the adhesion strength between epoxy and copper. Also, the surface of copper was treated by 1,1,1-trichloroethane. According to the results, the interfacial adhesion strength of copper-epoxy increased about 2~5 times with the introduction of silane primer. Also, the optimum treatment time of copper surface was about 10 minutes. Additionally, the adhesion strength as a function of concentration of low molecular weight silane was maximum at about 0.5 vol.% for 3-APTES and about 0.2 vol% for 3-GPTMS.

• Journal of Sensor Science and Technology
• /
• v.25 no.4
• /
• pp.247-251
• /
• 2016

Au/PDMS membranes are widely used to fabricate strain sensors which can detect input signals. An interfacial adhesion between metal films and polydimethylsiloxane (PDMS) substrates is one of the important factors determining the performance of strain sensors, in terms of robustness, reliability, and sensitivity. Here, we fabricate Au/PDMS membranes with (3-mercaptopropyl) trimethoxysilane (MPTMS) treatment. PDMS membranes were fabricated by spin-coating and the thickness was controlled by varying the spin rates. Au electrodes were deposited on the PDMS membrane by metal sputtering and the thickness was controlled by varying sputtering time. Owing to the MPTMS treatment, the interfacial adhesion between the Au electrode and the PDMS membrane was strengthened and the membrane was highly transparent. The Au electrode, fabricated with a sputtering time of 50 s, had the highest gauge factor at a maximum strain of ~0.7%, and the Au electrode fabricated with a sputtering time of 60 s had the maximum strain range among sputtering times of 50, 60, and 120 s. Our technique of using Au/PDMS with MPTMS treatment could be applied to the fabrication of strain sensors.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.581-583
• /
• 1993

One of the principal problems encountered in the use of fiber reinforced composites is to establish an active fiber surface to achieve maximum adhesion between resin and fiber surface. In order to improve the interface bonding, the surface of glass fiber should be treated with silane coupling agent in ordinary composite manufacturing processes. However, the price of the coupling agent is very high and in the treating process voids are formed, which decreasees electrical and mechanical strength. We want to develope new process that will overcome the disadvantage of the coupling agent and achieve maximum adhesion at the interface between resin and fiber by active plasma treatment on the glass fiber surface. In this study, we investigate the improvement of contact angle on the glass plate surface as the first step in developing new GFRP.

• Tribology and Lubricants
• /
• v.23 no.6
• /
• pp.288-297
• /
• 2007

Adhesion and friction tests were carried out in order to investigate the effect of temperature on the tribological characteristics of poly (methylmethacrylate) (PMMA) film using AFM. The pull-off and friction forces on the PMMA film were measured under a high vacuum condition (below $1{\times}10^{-4}$ Pa) as the temperature of the PMMA film was increased from 300 K to 420 K (heating) and decreased to 300K (cooling). Friction tests were also conducted in both high vacuum and air conditions at room temperature. When the temperature was 420 K, which is 25 K higher than the glass transition temperature $(T_g)$ of PMMA, the PMMA film surface became deformable. Subsequently, the pull-off force was proportional to the maximum applied load during the pull-off force measurement. In contrast, when the temperature was under 395 K, the pull-off force showed no correlation to the maximum applied load. The friction force began to increase when the temperature rose above 370 K, which is 25 K lower than the $T_g$ of PMMA, and rapidly increased at 420 K. Decrease of the PMMA film stiffness and plastic deformation of the PMMA film were observed at 420 K in force-displacement curves. After the heating to 420 K, the fiction coefficient was measured under the air condition at room temperature and was found to be lower than that measured before the heating. Additionally, the RMS roughness increased as a result of the heating.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.1
• /
• pp.16-20
• /
• 2006

In this paper, we investigated the effects of short-term oxygen plasma treatment of semiconducting silicone layer to improve interfacial performances in joints prepared with a insulating silicone materials. Surface characterizations were assessed using contact angle measurement and x-ray photoelectron spectroscopy (XPS), and then adhesion level and electrical performance were evaluated through T-peel tests and electrical breakdown voltage tests of treated semi-conductive and insulating joints. Plasma exposure mainly increased the polar component of surface energy from $0.21\;dyne/cm^2$ to $47\;dyne/cm^2$ with increasing plasma treatment time and then leveled off. Based on XPS analysis, the surface modification can be mainly ascribed to the creation of chemically active functional groups such as C-O, C=O and COH on semi-conductive silicone surface. This oxidized rubber layer is inorganic silica-like structure of Si bound with three to four oxygen atoms ($SiO_x,\;x=3{\sim}4$). The oxygen plasma treatment produces an increase in joint strength that is maximum for 10 min treatment. However, due to brittle property of this oxidized layer, the highly oxidized layer from too much extended treatment could be act as a weak point, decreasing the adhesion strength. In addition, electrical breakdown level of joints with adequate plasma treatment was increased by about $10\;\%$ with model samples of joints prepared with a semi-conducting/ insulating silicone polymer after applied to interface.

• Fashion & Textile Research Journal
• /
• v.13 no.5
• /
• pp.790-796
• /
• 2011

This study was designed to investigate the influence of ratio of anionic/nonionic surfactant mixture on detergency of particulate soil under various solutions. The detergency of the particulate soil was determined by adhesion of particle to fabric and its removal from fabric separately. The PET fabric and ${\alpha}-Fe_2O_3$were used as materials of textile and model of particulate soil, respectively. The detergency was investigated as a function of surfactants concentration, ionic strength, kinds of electrolyte and mole numbers of oxyethylene ether of nonionic surfactant in different ratio of anionic/nonionic surfactant mixture. Although some deviations exist, the adhesion of particle to fabric generally increased with decreasing its removal from fabric. The detergency of particulate soil on PET fabric was relatively higher in anionic/nonionic surfactant mixed solution than in each single surfactant solution, but the influence of ratio of anionic/nonionic surfactant mixture on detergency of particulate soil was low. Generally the detergency of particulate soil on fabric was at its maximum at 0.1% surfactant concentration, $1{\times}10^{-3}$ ionic strength, $Na_5P_3O_{10}$ electrolytes and 10 mole numbers of oxyethylene ether of nonionic surfactant, regardless of ratio of anionic/nonionic surfactant mixture.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.8
• /
• pp.706-710
• /
• 2007

Ti-containing amorphous carbon (a-C:Ti) films shows attractive mechanical properties such as low friction coefficient, good adhesion to various substrate and high wear resistance. The incorporation of titanium in a-C films is able to improve the electrical conductivity, friction coefficient and adhesion to various substrates. In this study, a-C:Ti films were depositied on Si wafer by closed-field unbalanced magnetron (CFUBM) sputtering system composed two targets of carbon and titanium. The tribological properties of a-C:Ti films were investigated with the increase of DC bias voltage from 0 V to - 200 V. The hardness and elastic modulus of films increase with the increase of DC bias voltage and the maximum hardness shows 21 GPa. Also, the coefficient of friction exhibites as low as 0.07 in the ambient. In the result, the a-C:Ti film obtained by CFUBM sputtering method improved the tribological properties with the increase of DC bias volatage.

• Journal of Adhesion and Interface
• /
• v.13 no.2
• /
• pp.89-93
• /
• 2012

In this study, the properties of acryl emulsion with adjunction procedures of tackifier resin and tackifier emulsion were investigated. Glass transition temperature of acryl emulsions was increased with the content of tackifiers. The initial strength showed the maximum value when the contents of tackifier resin and tackifier emulsion were 10 phr and 15 phr, respectively. Additionally, the strengths on heat and water resistances were increased with the contents of tackifier.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.59-60
• /
• 2022

When a metal sprayed film of several hundred ㎛ on the concrete surface is possible to 80 dB of shielding effect electromagnetic waves (ElectroMagnetic Pulse, EMP). Therefore, in this study, as a way to secure EMP shielding performance by applying a metal spray coating showing excellent EMP shielding performance to a concrete structure, the metal spray welding efficiency and thin film adhesion performance according to the concrete spray direction and surface treatment method were evaluated. Metal sprayed efficieny according to the metal spraying direction and method was confirmed that the difference was insignificant by applying the roughening agent. However, the method of strengthening the concrete surface and applying the sealing agent show maximum adhesion strength of 3.98 MPa compared to other methods, and it is judged that this method can be utilized for the metal spraying method for concrete EMP shielding.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10a
• /
• pp.350-355
• /
• 1998

Preplaced aggregate concrete in the building fields has recently been used in the partial repair works for damaged reinforced concrete structures, and polymer-modified mortars have been employed as grouting mortars for the preplaced aggregate concrete. The objective of this study is to clear the properties of polymer-modified grouting mortars. Polymer-modified mortars using a polystyrene acrylic(St/Ac) emulsion as grouting mortars for preplaced aggregate concrete are prepared with various mix proportions, and tested for flexural and compressive strengths, adhesion in tension. The flexural strength of emulsion-modified grouting mortars does not give much variation with increasing fly ash replacement for cement and sand-binder ratio. With increasing polymer-binder ratio, the flexural strength and adhesion in tension of St/Ac emulsion-modified grouting mortars increases, become nearly constant or reaches a maximum at a polymer-binder ratio of 5%. From the test results, St/Ac emulsion-modified grouting mortar with a polymer-binder ratio of 5%, a fly ash replacement of 10% for cement and sand-binder ratio of 1.0 is recommended as a grouting mortar for preplaced aggregate concrete.