• 한국응용과학기술학회지
• /
• 제24권1호
• /
• pp.23-30
• /
• 2007

Kevlar was chemically surface modified with resorcinol-formaldehyde(RF) prepolymer and VP rubber latex for application to high strength tirecords. RF prepolymer was easily obtained by polymerization at room temperature in the presence of a base catalyst. The mechanical and thermal properties of Kevlar were not significantly changed during surface treated under various conditions. The change of adhesion with rubber were investigated through H-test method. Maximum increase of adhesion force between rubber and Kevlar was obtained up to 40% than that of untreated one when the fiber was soaked in RFL dipping solution and thermally treated at $170^{\circ}C$ for 3 - 5min.

• 공업화학
• /
• 제28권4호
• /
• pp.454-459
• /
• 2017

본 실험은 다양한 계면활성제를 이용해 수성 아크릴 에멀젼 접착제를 제조하고 그 특성을 조사하였다. 제조한 접착제의 특성으로 고형분, 전환율, 입도분포, 초기접착력 등의 물성을 통해 비교하였다. 접착제의 고형분을 측정한 결과는 60% 이상의 높은 값을 나타냈으며 에멀젼 중합의 전환율은 합성한 계면활성제를 2 wt% 농도로 첨가하였을 때 97%로 측정되었다. 입도분포의 분석 결과는 양이온 계면활성제를 첨가한 경우에 290~470 nm의 작은 입자의 접착제가 제조되었고 초기접착력과 접착 발현시간 또한 증가되었다. 최대 접착력은 단일의 계면활성제(POE 23)를 사용했을 때 2.55 kgf의 값을 나타냈고 다른 계면활성제를 사용한 경우보다 뛰어나다는 것을 알 수 있었다. 양이온 제미니 계면활성제를 첨가하여 제조한 접착제의 부식방지력은 48 h 동안 유지되는 것을 확인할 수 있었다.

• 전력전자학회논문지
• /
• 제8권4호
• /
• pp.366-374
• /
• 2003

본 논문에서는 최대 견인력 제어를 위해서 부하 토크 외란 관측기를 이용하여 점착력 계수를 추정하고 추정한 점착력 계수의 미분치를 PI 토크 제어하는 Anti-slip 제어를 제안한다. 부하 토크 외란 관측기는 회전자의 위치 정보와 토크 전류의 정보를 이용하여 부하 외란 토크를 추정하고, 부하 외란 토크에 철도차량 상수를 미용하여 점착력 계수를 추정한다. 또한 부하토크외란 관측기는 구조가 간단하며, 시스템의 외란 및 각종 제어이득. 시스템의 상수 변화에 대해서도 견실한 견인력 제어 특성을 가지고 있다. 이와 같은 제어 알고리즘을 구현하기 위하여 IC4M(1-Controller 4-Motor) 축소형 철도차량시스템을 이용하여 제안된 알고리즘을 시뮬레이션과 실험을 통하여 확인하였다. 또한 실제 철도차량시스템의 경우 선로 표면의 상태 변화 및 차량속도의 가감에 따른 공전속도에 대한 점착력의 관계를 축소형 철도차량시스템으로 구현하여, 실제 철도차랑시스템의 경우와 비교 분석하여 최대 견인력제어가 되도록 하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제34권2호
• /
• pp.37-45
• /
• 2006

The viscoelastic properties of blends of melamine-formaldehyde (MF) resin and poly(vinyl acetate) (PVAc) for engineered flooring used on the Korean traditional ONDOL house floor heating system were investigated by dynamic mechanical thermal analysis (DMTA). Because MF resin is a thermosetting adhesive, the effect of MF rein was shown across all thermal behaviors. The addition of PVAc reduced the curing temperature. The DMTA thermogram of MF resin showed that the storage modulus (E') increased as the temperature was further increased as a result of the cross-linking induced by the curing reaction of the resin. The storage modulus (E') of MF resin increased both as a function of increasing temperature and with increasing heating rate. From isothermal DMTA results, peak $T_{tan{\delta}}$ values, maximum value of loss modulus (E") and the rigidities (${\Delta}E$) of MF/PVAc blends at room temperature as a function of open time, peak $T_{tan{\delta}}$ and maximum loss modulus (E") values were found to increase with blend MF content. Moreover, the rigidities of the 70:30 and 50:50 MF/PVAc blends were higher than those of the other blends, especially of 100% PVAc or MF. We concluded that blends the MF/PVAc blend ratios correlate during the adhesion process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.422-426
• /
• 2003

Cu thin films of $6000{\AA}$ thickness were deposited by Electron Beam Evaporation(EBE) method on the glass. The resistivity properties and adhesion of Cu thin films were investigated by various annealing and substrate temperature. Cu thin films were annealed in the air and vacuum condition for 10 min after the deposition. The resistivity and adhesion(the force required to separate films from substrates) was measured by 4-point probe and scratch testing. The resistivity of non-annealing Cu thin films was distinguished more substrate temperature loot than substrate temperature R.T, $200^{\circ}C$. In the case of air condition annealing, as heating temperature was increased, the resistivity was decreased. In the case of vacuum condition annealing, the resistivity was increased at heating temperature $200^{\circ}C$. The best resistivity($1.72\;{\mu}{\Omega}{\cdot}cm$) of Cu thin films was obtained by the air condition heating temperature $200^{\circ}C$ at the substrate heating temperature $100^{\circ}C$. As a result of scratch testing, adhesion was increased by annealing. And maximum adhesion had 600 gf.

• 대한건축학회논문집:구조계
• /
• 제35권11호
• /
• pp.147-154
• /
• 2019

The purpose of this study is to evaluate the effect of admixtures as blast-furnace slag(BF) and fly ash(FA) on tensile and adhesive properties of polymer cement mortar(PCM) with EVA emulsion. The test specimens are prepared with five polymer-cement ratio(P/C) and five admixture contents, and tested for tensile strength and adhesion in tension. From the test results, the tensile strength and adhesion in tension could be improved by an appropriate combination of P/C and admixture contents. In particular, the maximum of tensile strength of PCM with P/C 10% and BF content of 10% is 4.70MPa which is about 1.55 times higher than that of plain mortar, and about 1.22 times that of PCM that does not contain any mixture. The ratio of adhesion in tension to tensile strength of PCM with admixtures averaged 55.8%. It is also apparent that admixture contents of 5% or 10% could be proposed for improvement of tensile strength and adhesion in tension of PCM.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2022년도 가을 학술논문 발표대회
• /
• pp.83-84
• /
• 2022

Zero-energy construction is being emphasized due to environmental pollution. However, in the case of external insulation using organic insulation with good insulation performance, there are many studies on inorganic insulation as it shows limitations on fire stability. In addition, as the demand for stone for exterior walls increases, Cellular Light -weight Concrete(CLC) with polymer is used to supplement fire stability and insulation performance, and the construction of stone is complemented by combining organic insulation, inorganic insulation, and stone. In this study, the compressive strength and adhesion in tension of CLC are studied. As a result of the experiment, the compressive strength of 28 days according to the polymer addition rate did not change. The adhesion in tension according to the polymer addition rate tends to increase as the addition rate increases. The target adhesion in tension is 0.8 MPa, but the maximum value of the experiment did not reach the target value, and further research was needed to combine to maintain the density and improve the adhesion in tension.

• The Journal of Advanced Prosthodontics
• /
• 제9권5호
• /
• pp.335-340
• /
• 2017

PURPOSE. Bacterial adhesion on provisional crown materials retained for a long time can influence the duration for which permanent prosthetic restorations can be healthily worn in the oral cavity. The aim of this study was to compare seven different commonly used provisional crown materials with regard to Streptococcus mutans and Candida albicans surface adhesion. MATERIALS AND METHODS. For each group, twenty specimens of the provisional fixed prosthodontic materials TemDent ($Sch{\ddot{u}}tz$), Imident (Imicryl), Tab 2000 (Kerr), Structur Premium (Voco), Systemp (Ivoclar Vivadent), Acrytemp (Zhermack), and Takilon-BBF (Takilon) were prepared (diameter, 10.0 mm; height, 2.0 mm). Surface roughness was assessed by atomic force microscopy. Each group was then divided into 2 subgroups (n=10) according to the microbial suspensions used: S. mutans and C. albicans. The specimens were incubated at $37^{\circ}C$ with S. mutans or C. albicans for seven days. Bacterial adherence on surfaces was assessed using the 2,3-bis[2-methyloxy-4-nitro-5-sulfophenyl]-2H-tetrazolium-5-carboxanilide (XTT) assay. RESULTS. S. mutans showed maximum adhesion to Structur, followed by Systemp, Acrytemp, Takilon, Tab 2000, Imident, and TemDent (P<.05). The highest vital C. albicans adhesion was noted on Takilon, followed by Imident and Tab 2000; the lowest adhesion was noted on Systemp (P<.05). CONCLUSION. The materials showed significant differences in the degree of bacterial adhesion. C. albicans showed higher surface adhesion than S. mutans on provisional crown and fixed partial denture denture materials.

• Archives of Plastic Surgery
• /
• 제36권5호
• /
• pp.543-547
• /
• 2009

Purpose: Adhesion is the most common and troublesome complication after repair of flexor tendon injury. Recently, use of sodium hyaluronate derivatives for adhesion prevention is increasing. A commercial product, Guardix$^{(R)}$, sodium hyaluronate(NaHe) combined with carboxymethylcellulose(CMC) has been newly developed as a preventive material for adhesion. We have investigated its effect in rabbits. Methods: Twenty seven male New Zealand white rabbits were operated under ketamine anesthesia. After tendon repair in zone II of the hind paw, Guardix$^{(R)}$(experimental group) or normal saline(control group) was administered. Biomechanical tests were performed to estimate adhesion formation at 2, 4, 8, and 12 weeks after the operation. Maximum tensile load to flex the distal interphalangeal joint 50 degree from its resting state(MTL50) was measured, depicting the amount of adhesion formed. Subsequently, breaking strength was assessed. Results: There were no postoperative complications such as infection, wound dehiscence, or hematoma. MTL50 was significantly lower in the experimental group than in the control group at 4, 8, 12 weeks (p<0.05). Mean value of MTL50 was 6.64N in the experimental group and 28.53N in the control group at 12 weeks after surgery. There were no significant differences in breaking strength. Conclusion: Our results indicate that Guardix$^{(R)}$ is helpful in reducing adhesion formation and does not interfere with normal healing processes of the tendon.

• Journal of Welding and Joining
• /
• 제4권3호
• /
• pp.50-57
• /
• 1986

In this study, the experiments were earried out for the purpose of the clarifying the optimum metal arc spraying conditions, such as spraying distance, wire feed speed, arc current, etc, by using the stainless steel wire ER 308L. Main results obtained are as follows: 1. Optimum spraying distance is closely related to the equilibrium temperature of base material in back surface. 2. The size fused metal particles is increased according to the temperature of fused metal. 3. The maximum adhesion strength of coatings is obtained under the optimum spraying conditions of which the temperature of fundamental is maximum.