• Tribology and Lubricants
• /
• v.27 no.5
• /
• pp.240-248
• /
• 2011

Mechanical face seal installed in primary heat transport pump used for heavy water reactor prevents leakage of working fluid using thin working fluid film between primary seal ring and mating ring. If the leakage of working fluid exceeds the allowable volume, serious accident can be happened by the trouble of primary heat transport pump. The thinner fluid film exists between primary seal ring and mating ring, the less working fluid leaks out. On the other hand, if the thickness of fluid film is not enough, the life of mechanical face seal will be reduced by friction and wear. Therefore appropriate design is necessary to maximize the performance and life of mechanical face seal. In this study, numerical analysis using finite volume method was conducted to investigate the performance of mechanical face seals which have same deep straight groove and 11 different net coning values. As results, equilibrium clearance between primary seal ring and mating ring, leakage volume of working fluid, friction torque on sealing surface and stiffness of working fluid film were obtained. With increasing net coning value, equilibrium clearance and leakage volume increase, and friction torque and stiffness of fluid film decrease.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.693-698
• /
• 1991

This paper describes a fuzzy rule-based assembly algorithm for precision parts mating, The difficulties in devising reliable assembly strategies result from the complexity of the assembly process and the uncertainty such as imperfect knowledge of the parts being assembled as well as the limitations of the devices performing the assembly. To cope with above problems, we propose an assembly algorithm utilizing fuzzy set theory. The presented method allows us to represent the uncertainty by using fuzzy membership function and treat nonlinear sapping from measured force/torque to corrective motions using rules. Finally, the performance of this method is evaluated through a series of experiments. Experimental results show that the proposed method can be effectively used for chamferless and precision parts mating.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.1072-1077
• /
• 1992

In ths paper a new active assembly algorithm for chamferless precision parts mating, is considered. The successful assembly task requires an extremely high position accuracy and a good knowledge of mating parts. However, conventional assembly mehtod alone makes it difficult to achieve satisfactory assembly performance because of the complexity and the uncertainties of the process and its environments such as imperfect knowledge of the parts being assembled as well as the limitation of the devices performing the assebled as well as the limitation of the devices performing the assembly. To cope with these problems, a self-learning rule-based assembly algorithm is proposed by intergaring fuzzy set theory and neural network. In this algortihm, fuzzy set theory copes with the complexity and the uncertainties of the assembly process, while neural network enhances the assembly schemen so as to learn fuzzy rules form experience and adapt to changes in environment of uncertainty and imprecision. The performance of the proposed assembly algorithm is evaluated through a series of experiments. The results show that the self-learning fuzzy assembly scheme can be effecitively applied to chamferless precision parts mating.

• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.419-424
• /
• 1986

A technique is developed which allows a designer to interactively create an assembly of components by specifying mating contions between the individual components. Once establishing the relationships between components via the mating conditions, each component's location and orientation in the final assembly is computed. The joint information for a kinematic and dynamic analysis can be derived from the mating conditions, therefore this work may be extended to incorporate this analysis. Thorugh this development it will no longer be necessary for a designer to specify cumbersome and error prone transformation matrices in order to create an assembly. The designer also will be able to perform a kinematic or a dynamic analysis directly from an assembly model if the joint information can be automatically derived.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.1
• /
• pp.48-58
• /
• 1989

An assembly modeling system, with which a designer can interactively create an assembly of components ready for the dynamic analysis, has been developed. In this system, an assembly model is created from the mating conditions between the components in the assembly, and then most information required for the dynamic or kinematic analysis packages are derived. For this development, the following problems have been solved; the creation of assembly data structure, the derivation of the joint information, the inference of each component's position, and the creation of the joint coordinate systems. Through this work, the designer can easily model an assembly by assigning mating conditions, and check the dynamic or kinematic performance with the automatic creation of inputs for the assembly analysis packages.

• Journal of Ecology and Environment
• /
• v.30 no.3
• /
• pp.225-229
• /
• 2007

The mating systems of natural populations of Potentilla freyniana in Korea were determined using allozyme analysis. The result suggests that P. freyniana is outcrossing as well as employing vegetative reproduction by stolon (self-fertilization rate, s < 0.5). The values of the inbreeding coefficient of eight populations in Korea varied from 0.244 to 0.331, with an average value of 0.274. For eight natural populations, multi-locus estimates of outcrossing (tm) was 0.603 across 13 polymorphic loci, with individual population values ranging from 0.530 to 0.652. The relatively low outcrossing rates of some populations could be attributed to extensive vegetative reproduction by stolon and the isolation of flowering mature plants. Although P. freyniana usually propagated by asexually-produced ramets, I could not rule out the possibility that sexual reproduction occurred at a low rate because each ramet may produce terminal flowers. Although heterozygote excess was observed in some natural populations, most populations exhibited varying degrees of inbreeding and a heterozygote deficit.

• Animal cells and systems
• /
• v.13 no.1
• /
• pp.71-78
• /
• 2009

To clarify the reproductive function of vibration signals in Hynobius, which has externally fertilized eggs, we quantitatively analyzed the body and tail undulations of male Korean salamanders (Hynobius leechii) in sixteen mating events. One large and one small male, and one female were used in each mating event. We analyzed behaviors recorded over a total of 3 hrs for each mating event; 2 hrs before and 1 hr after female's oviposition. Males touched females using their snouts or body trunk throughout the entire mating periods, but females touched males increasingly more after approximately 1 hr before oviposition. Males conducted body undulations more than 50 times per 10 minutes at a mean frequency of 0.64 Hz. Large males conducted more body undulations than small males, particularly on the tree twig where females attached their egg sacs. Males responded to other males' body undulation throughout the mating period by orienting their head towards, approaching, and touching the undulating male. Females only responded for about 10-20 min before ovipositing, and most responses were directed to the large male's body undulation. Males conducted tail undulations 3.0 times per 10 min at a mean frequency of 1.7 Hz and most tail undulations occurred after one male bit the other male. These results suggest that body undulations function in both male-female and male-male interactions, while tail undulations mainly functions in male-male competition. Also, male H. leechii appear to actively attract females, while females respond to the males only at times close to oviposition.

• Animal cells and systems
• /
• v.2 no.4
• /
• pp.463-469
• /
• 1998

Hyla japonica males were observed to produce two distinctively different types of mating calls: advertisement call to attract conspecific females and encounter call to keep off potential competitor males. Whereas advertisement calls were organized in bouts of calls or notes, encounter calls were usually produced as separate calls. Encounter calls were much longer and had more pulses per call than advertisement calls. However dominant frequencies or pitches of the two calls did not differ significantly. Hyla Japonica males exhibited considerable plasticity in their calling behavior. They altered both qualitative and quantitative properties of their calls in response to other calling males. Sometimes, they even switched from producing advertisement calls to encounter calls. Advertisement calls produced by chorusing males were shorter in duration and thus move calls per bout than those produced by lone males. Males also produced much lower-pitched calls when calling together with other males. Considering that low pitch calls are often Highly correlated with body size, it is possible that H. japonica males may try to generate deceptive calls to indicate the size greater than the actual.

• Journal of Animal Science and Technology
• /
• v.59 no.12
• /
• pp.25.1-25.7
• /
• 2017

Background: Rabbit breeding with high performance imported ones would be of benefit for genetic diversity and improvement of performance in domestic rabbit breeds. The rearing of more productive rabbit breeds could be pathway to improve the productivity and reduce the production cost. Maternal nutritional status exert a great influence on reproductive functions of does, which may expand from conception, through gestation and parturition and development of kits to puberty. Methods: Four breeds of rabbit were evaluated for their parturition, weaning and pubertal differences among the rabbit population in Ibadan, Nigeria. The breed consist of Fauve De Bourgogne (FDB), Chinchilla (CHA), British Spot (BS) and New Zealand White (NZW) rabbits. A total of 60 bucks and 360 does consisting of 15 bucks and 90 does per breed were mated in 6 mating cycles, three each of natural mating and artificial insemination. All does were synchronized for estrus with 20 IU pregnant mare serum gonadotropin 48 h prior to mating. The does after parturition were assessed for milk yield (g) and kit survival rate (%) till weaning, weight changes of kits from birth to puberty. At puberty, the pubertal age (days) and weight (g) of the offspring were assessed. Result: Results obtained reveals that British Spot doe had highest milk yield among the breeds which significantly increased growth of kit and weight at weaning in British Spot rabbits. Survival rates of Chinchilla kits were significantly (p < 0.05) higher than Fauve de Bourgogne, British Spot and New Zealand White kits. Puberty attainment of the rabbits indicates that British spot does and Fauve de Bourgogne bucks are early maturing. Conclusion: Chinchilla shows high kit survivability and British spot has highest milk yield among the four breeds of rabbit.

• Proceedings of the Zoological Society Korea Conference
• /
• 1999.10b
• /
• pp.294.1-294
• /
• 1999

No Abstract, See Full Text