• Applied Chemistry for Engineering
• /
• v.25 no.2
• /
• pp.181-187
• /
• 2014

In order to use the spherical atomizing reduction steel slag (ladle furnace slag, LFS) instead of the fine aggregate of polymer concrete composites, various specimens were prepared with various replacement ratios of atomizing reduction steel slag and the addition ratios of polymer binder. Physical properties of these specimens were investigated through the absorption test, the compressive strength test, the flexural strength test, the hot water resistance test, the pore analysis and the micro-structure using scanning electron microscope. Results showed that the compressive strength and flexural strength of specimens with 7.5% of polymer binders increased with the increase of replacement ratios of atomizing reduction steel slag, but those of the specimens with 8.0% or more of polymer binders showed a maximum strength at a certain replacement ratio due to the material segregation causing the increase of fluidity. By hot water resistance tests, the compressive strength, flexural strength, average pore diameter, and bulk density decreased but the total pore volume and pore diameter increased. It was concluded that the amount of polymer binders could be reduced by maximum 23.8%, because the workability of the polymer concrete was remarkably improved by using the atomizing reduction steel slag instead of fine aggregate. However, since the use of atomizing reduction steel slag decreased the resistance of the polymer concrete to hot water, further studies are required.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.5
• /
• pp.92-103
• /
• 2015

Box-Wilson experimental design method, known as central composite design, is the design of any information-gathering exercises where variation is present. This method was devised to gather as much data as possible in spite of the low design cost. This method was employed to model the effect of mixing factors on several performances of 60 MPa high strength self compacting concrete and to numerically calculate the optimal mix proportion. The nonlinear relations between factors and responses of HSSCC were approximated in the form of second order polynomial equation. In order to characterize five performances like compressive strength, passing ability, segregation resistance, manufacturing cost and density depending on five factors like water-binder ratio, cement content, fine aggregate percentage, fly ash content and superplasticizer content, the experiments were made at the total 52 experimental points composed of 32 factorial points, 10 axial points and 10 center points. The study results showed that Box-Wilson experimental design was really effective in designing the experiments and analyzing the relation between factor and response.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.46 no.1
• /
• pp.31-42
• /
• 2020

Horse fat is known to be an effective ingredient in Asia, and the horse fat itself, which is mixed with other ingredients at the additive level, is often sold as a finished product. In this case, physical properties of the horse fat raw material are important. Many horse fats produced in Korea (Jeju) have low temperature stability, so if not stored at low temperatures, segregation may occur. In the case of Japanese horse fat, it is partially hydrogenated or is used the solid phase as the horse fat by separating the liquid phase and the solid phase that is harder and more stable than the horse fat of Jeju. In this study, the physical properties were tested to improve the temperature stability even without the partial hydrogenation process of Jeju horse fat. Various oil gelling agents were used in the study. Results confirmed that the physical properties of the hydroxystearic acid added Jeju horse fat were improved. In addition, stability evaluations at temperatures of 25 ℃, 40 ℃, 45 ℃ and flow behavior evaluations at temperatures of 25 ℃, 30 ℃, 40 ℃ were performed for Jeju horse fat with hydroxystearic acid, 100% Jeju horse fat, and 100% Japanese horse fat. Results showed that the Jeju horse fat improved in flow behavior by adding hydroxystearic acid similar to that of Japanese horse fat. In addition, when the crystal state was observed under a microscope, the thermal stability was improved by decreasing the size of the needle-type crystals with the addition of hydroxystearic acid. Jeju horse fat containing hydroxystearic acid was found to have no physical problems even when stored at room temperature for a long time.

• Korean Journal of Heritage: History & Science
• /
• v.52 no.4
• /
• pp.170-183
• /
• 2019

Fiber scutching refers to the process of extracting fibers from plants by separating or extracting fibers from the raw materials. As the definition of the term implies, the "Fiber Scutching" is performed on plants with advanced bast fiber as the primary material processing technique performed on plant materials. Some of the most popular phosphorus plants are ramie, hemp, flax, and the paper mulberry, which have a long history of cultivation and a wide range of distribution, making them very universal as a material supporting human life and culture. This study was described in Oju-yeonmunjangjeon-sango but was designed to re-examine the method of breaking dried stalks, which is currently unused in Korea, to examine the feasibility and characteristics of the technology. As a result of sampling and experimenting with hemp bast using the method recorded in the literature, hemp fiber was actually produced. The criteria for removing the shell from the hemp stem were the degree of discoloration and drying, and only when the stalk was completely discolored to yellow could segregation of the stalk from the shell be performed. The amount of sunlight and temperature were conditions that accelerated drying. However, if exposed for a long time, it is confirmed that hemp bast will be in a suitable condition to process, regardless of the amount of sunlight and temperature. 'Breaking of dried stalks', which utilizes the physical power of 'threshing with a flail' is considered a core process of the fiber scutching technique in 'Yukjin' in Hamgyeong-do. The bark and the core of the hemp were separated by tapping, the bast was thinly split, and the shell was peeled off, making it suitable for collecting with thread. The method of collecting the fibers by applying physical power causes downing on the fibers, which is to be generally avoided in the manufacture of bast fabric woven hemp or ramie. However, Hamgyeong-do's fiber scutching method seems to have applied this principle to the method of making fragile fabrics by using it in reverse. This method is distinct from the steaming or boiling of the stalks' in Andong, Korea, and it is similar to the Western method of spinning fabrics.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.2
• /
• pp.1-10
• /
• 2014

In this study, two different types of dredged fill injection methods are introduced and filling experiments were conducted to analyze the impact of each technique to the distribution and deposition of dredged soil fill and how it influence the final tube shape. Two transparent plastic tubes were fabricated to observe the deposition behavior of the deposited fill material. Both tubes measured 4.0 meters in length (L) and has vinyl tube diameters (D) of 0.5m and 0.7m. T-type and I-type inlet system are also introduced in this paper. The influence of this inlet systems to the distribution and deposition behavior of dredged soil fill inside the vinyl tubes were observed during the experiment. After the sedimentation of the slurry mixture, the water on top of the soil sediments are removed and the slurry mixture was re-injected into the vinyl tube, this process was carried out repeatedly. The shape changes of the vinyl tube, e.g. the changes in both tube height and width, are constantly monitored after each slurry injection and water draining phases. Crater formation was observed in the case of I-Type inlet system and a non-uniform sediment distribution occurred. For the diffusion deposit of soil particles to long distance are minimal shape technique using the T-Type inlet system. Therefore the undrain filling height ratio ($H/D_0$) was found to be around 0.54 to 0.64 and the horizontal strain ratio ($W/D_0$) ranges from 1.45 to 1.54. The filling soil height is proportional to dredged-material filling phases, but, horizontal strain ratio is constant or inversely reduced so that the center of tube body is raised in the upward direction.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.154-155
• /
• 2012

The promise of nano-crystalites (nc) as a technological material, for applications including display backplane, and solar cells, may ultimately depend on tailoring their behavior through doping and crystallinity. Impurities can strongly modify electronic and optical properties of bulk and nc semiconductors. Highly doped dopant also effect structural properties (both grain size, crystal fraction) of nc-Si thin film. As discussed in several literatures, P atoms or radicals have the tendency to reside on the surface of nc. The P-radical segregation on the nano-grain surfaces that called self-purification may reduce the possibility of new nucleation because of the five-coordination of P. In addition, the P doping levels of ${\sim}2{\times}10^{21}\;at/cm^3$ is the solubility limitation of P in Si; the solubility of nc thin film should be smaller. Therefore, the non-activated P tends to segregate on the grain boundaries and the surface of nc. These mechanisms could prevent new nucleation on the existing grain surface. Therefore, most researches shown that highly doped nc-thin film by using conventional PECVD deposition system tended to have low crystallinity, where the formation energy of nucleation should be higher than the nc surface in the intrinsic materials. If the deposition technology that can make highly doped and simultaneously highly crystallized nc at low temperature, it can lead processes of next generation flexible devices. Recently, we are developing a novel CVD technology with a neutral particle beam (NPB) source, named as neutral beam assisted CVD (NBaCVD), which controls the energy of incident neutral particles in the range of 1~300eV in order to enhance the atomic activation and crystalline of thin films at low temperatures. During the formation of the nc-/pm-Si thin films by the NBaCVD with various process conditions, NPB energy directly controlled by the reflector bias and effectively increased crystal fraction (~80%) by uniformly distributed nc grains with 3~10 nm size. In the case of phosphorous doped Si thin films, the doping efficiency also increased as increasing the reflector bias (i.e. increasing NPB energy). At 330V of reflector bias, activation energy of the doped nc-Si thin film reduced as low as 0.001 eV. This means dopants are fully occupied as substitutional site, even though the Si thin film has nano-sized grain structure. And activated dopant concentration is recorded as high as up to 1020 #/$cm^3$ at very low process temperature (＜ $80^{\circ}C$) process without any post annealing. Theoretical solubility for the higher dopant concentration in Si thin film for order of 1020 #/$cm^3$ can be done only high temperature process or post annealing over $650^{\circ}C$. In general, as decreasing the grain size, the dopant binding energy increases as ratio of 1 of diameter of grain and the dopant hardly be activated. The highly doped nc-Si thin film by low-temperature NBaCVD process had smaller average grain size under 10 nm (measured by GIWAXS, GISAXS and TEM analysis), but achieved very higher activation of phosphorous dopant; NB energy sufficiently transports its energy to doping and crystallization even though without supplying additional thermal energy. TEM image shows that incubation layer does not formed between nc-Si film and SiO2 under later and highly crystallized nc-Si film is constructed with uniformly distributed nano-grains in polymorphous tissues. The nucleation should be start at the first layer on the SiO2 later, but it hardly growth to be cone-shaped micro-size grains. The nc-grain evenly embedded pm-Si thin film can be formatted by competition of the nucleation and the crystal growing, which depend on the NPB energies. In the evaluation of the light soaking degradation of photoconductivity, while conventional intrinsic and n-type doped a-Si thin films appeared typical degradation of photoconductivity, all of the nc-Si thin films processed by the NBaCVD show only a few % of degradation of it. From FTIR and RAMAN spectra, the energetic hydrogen NB atoms passivate nano-grain boundaries during the NBaCVD process because of the high diffusivity and chemical potential of hydrogen atoms.

• Microbiology and Biotechnology Letters
• /
• v.41 no.2
• /
• pp.228-235
• /
• 2013

Radish (Raphanus sativus) is a common cruciferous vegetable, and its aerial parts, called Mu-chung in Korean, have plentiful nutritional components such as vitamins, minerals and dietary fibers. Mu-chung has been used as a kimchi, a traditional Korean fermented dish, and dried Mu-chung is an important component of soups commonly consumed during winter in Korea. Since the advent of the mass production of radish in Korea, with the segregation of farm areas and towns and changing diets, Mu-chung has mostly been discarded instead of utilized. In addition, studies concerning the efficient utilization and useful bioactivities of Mu-chung are still lacking worldwide. In this study, we prepared the ethanol extract of Mu-chung and its subsequent solvent fractions. Antimicrobial, antioxidation, and anticoagulation activities were then evaluated in the hopes of developing a functional biomaterial from Korean radishes' aerial parts. The ethanol extraction yield for hot-air dried Mu-chung was 5.6%, and the fraction yields of n-hexane (H), ethylacetate (EA), butanol (B) and water residue were 25.3, 3.6, 19.4, and 51.7%, respectively. Analysis of total polyphenol and total flavonoid contents showed that the EA fraction had the highest content (97.57 and 152.91 mg/g) amongst the fractions. In antimicrobial activity assays, the H and EA fractions were effective against gram positive bacteria (Staphylococcus aureus, Listeria monocytogenes, and Bacillus subtilis), but not effective against gram negative bacteria (Escherichia coli and Pseudomonas aeruginosa). The B fraction also exhibited moderate antibacterial activity, suggesting that the extract of Mu-chung has various antibacterial components. In antioxidation activity assays, the EA fraction showed strong DPPH, ABTS and nitrite scavenging activities ($69-222{\mu}g/ml$ of $IC_{50}$), including reducing power. In anticoagulation activity assays, the EA fraction demonstrated strong inhibition activity against human thrombin and prothrombin. Prominent anticoagulation activity was found in aPTT assays; the aPTT of the EA fraction was extended 15-fold compared than that of the solvent control. Our results suggest that Mu-chung is an attractive nutritional food material possessing useful bioactivities, and the EA fraction of Mu-chung could be developed as a functional food ingredient.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.66 no.3
• /
• pp.248-255
• /
• 2021

This study was conducted to obtain basal information for the development of perilla cultivars with improved quality. The F₇ population of recombinant inbred lines (RILs) from a cross between the parents of Daesil for seeds and Ipdeulkkae1 for vegetables was used as the material. We evaluated several agricultural characteristics and seed quality. Variations were observed in most of the measurements; for example, stem length (ranging from 66.0 to 150.0 cm), number of branches (from 5 to 23), flower cluster length (ranging from 5.1 to 10.5 cm), number of flower clusters (from 17 to 131), a-linolenic acid content (from 54.2 to 64.1%), and functional compound content (rosmarinic acid 869.5~3,508.1 ㎍/g; luteolin 47.4~864.3 ㎍/g; apigenin 57.1~296.7 ㎍/g) all showed variation. Significant correlations between stem length and the number of branches (0.561) and number of branches versus number of flower clusters (0.638) were detected in the RIL F₇ population. Most agricultural characteristics and seed qualities showed a normal distribution with large variation, and transgressive segregation was observed in many descendants with characteristics to those of their parents. Daesil/Ipdeulkkae1 RIL F₇ populations could be useful for future QTL analysis as well as for intermediate breeding lines for high-quality perilla cultivars.