• Korean Journal of Chemical Engineering
• /
• 제35권11호
• /
• pp.2321-2326
• /
• 2018

We evaluated the optimal conditions for fluidization of nickel oxide (NiO) and its reduction into high-purity Ni during hydrogen reduction in a laboratory-scale fluidized bed reactor. A comparative study was performed through structural shape analysis using scanning electron microscopy (SEM); variance in pressure drop, minimum fluidization velocity, terminal velocity, reduction rate, and mass loss were assessed at temperatures ranging from 400 to $600^{\circ}C$ and at 20, 40, and 60 min in reaction time. We estimated the sample weight with most active fluidization to be 200 g based on the bed diameter of the fluidized bed reactor and height of the stocked material. The optimal conditions for NiO hydrogen reduction were found to be height of sample H to the internal fluidized bed reactor diameter D was H/D=1, reaction temperature of $550^{\circ}C$, reaction time of 60 min, superficial gas velocity of 0.011 m/s, and pressure drop of 77 Pa during fluidization. We determined the best operating conditions for the NiO hydrogen reduction process based on these findings.

• 한국결정성장학회지
• /
• 제14권2호
• /
• pp.50-57
• /
• 2004

Mercurous Bromide ($Hg_2Br_2$) crystals hold promise for many acousto-optic and opto-electronic applications. This material is prepared in closed ampoules by the physical vapor transport (PVT) growth method. We investigate the effects of solutal convection on the crystal growth rate in a horizontal configuration for diffusive-convection conditions and purely diffusion conditions achievable in a low gravity environment. Our results show that the growth rate is decreased by a factor of one-fourth with a ten reduction of gravitational acceleration near y = 2.0 cm. For 0.1 $g_O$ the growth rate pattern exhibits relatively flat which is intimately related to diffusion-dominated processes. The growth rate nonuniformity is regardless of aspect ratio across the interfacial positions from 0 to 1.5. Also, the effect of a factor of the ten reduction in the gravitational acceleration is same to both Ar = 5 and 2. The enlargement in the molecular weight of B from 50 to 500 by a factor 4 causes a decrease in the maximum growth rate by the same factor, indicative of the effect of solutal gradients.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.112-116
• /
• 2000

This paper presents anisotropic ethcing characteristics of single-crystal silicon in tetramethylammonium hydroxide(TMAH):isopropyl alcohol(IPA) solutions containing pyrazine. With the addition of IPA to TMAH solutions, etching characteristics are exhibited that indicate an improvement in flatness on the etching front and a reduction in undercutting, but the etch rate on (100) silicon is decreased. The (100) silicon etch rate is improved by the addition of pyrazine. An etch rate on (100) silicon of $0.8\;{\mu}m/min$, which is faster by 13 % than a 20 wt.% solution of pure TMAH, is obtained using 20 wt.% TMAH:0.5 g/100 ml pyrazine solutions, but the etch rate on (100) silicon is decreased if more pyrazine is added. With the addition of pyrazine to a 25 wt.% TMAH solution, variations in flatness on the etching front were not observed and the undercutting ratio was reduced by 30 ~ 50 %.

• Agricultural and Biosystems Engineering
• /
• 제3권2호
• /
• pp.59-64
• /
• 2002

Odor generated during composting of livestock manure is mainly due to ammonia emission. Biofiltration is a desirable method to control composting odor. This study was conducted to analyze the efficiency of using fresh compost as a biofilter. A mixture of cattle manure and recycled compost was composted in a bin equipped with a suction-type blower. The exhaust gas was filtered through the fresh compost. Residence time was controlled by the flow rate of exhaust gas and the depth of filtering materials. At the aeration rate of 30 L/min(experiment I), ammonia reduction rate varied from 100% to -15% for biofilter A(residence time 56.5 s) and almost 100% for biofilter B(residence time 113 s). At the aeration rate of 30 L/min, the cumulative ammonia reduction rate was 80.5% for biofilter A and 99.9% for biofilter B. At the aeration rate of 50 L/min(experiment II), the lowest reduction rate showed a negative value of -350% on the 8th and 9th day for biofilter A(residence time 33.9 5), and 50% on the loth day for biofilter B(residence time 67.8s). At the aeration rate of 50 L/min, the cumulative ammonia reduction rate was 82.5% fur biofilter A and 97.4% for biofilter B. Filtering efficiency was influenced by residence time. The moisture content(MC) and total nitrogen(T-N) of the filtering material were increased by absorbing moisture and ammonia included in the exhaust gas, while pH was decreased and total carbon(T-C) remained unchanged during the filtering operation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.461-464
• /
• 2004

The reduction effect of floor impact noise depends on the various factors such as stiffness and thickness of the concrete slab, finishing If ceiling materials and the composition method. Among the rest it is well known that floating floor system is more effective. Standard floating floor(SFF) type-2 consisted of 50mm lightweight aerated concrete(LAC) and 20mm damping material has been widely used. But LAC construction problem on dry damping material occurred and the reduction effect of floor impact noise has bare minimum qualifications. Thus the aim of this study is to develop 40mm composite damping material(Soundzero Plus) for SFF type-5 which substitute LAC and damping material. 'Soundzero Plus' is satisfied with quality requirement for damping material for SFF. The heat transition rate, $0.45W/m^2{\cdot}K$ is more effective 55% about than the regulation. The test results of floor impact noise by using 'Soundzero Plus' are showed good improvement about 12dB (tested by tapping machine) and 4dB (tested by bang machine) between before and after.

• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2012년도 제46차 학술발표회
• /
• pp.55-55
• /
• 2012

To improve the deodorizing and antibacterial performance of various fabrics (cotton, silk and wool) dyed with pomegranate(Punica granatum L.) extract without mordants, natural colorant solutions, which were extracted from pomegranate using water as an extractant at $90^{\circ}C$ for 90 min with a various liquor ratio (solid natural colorant material/solvent water, weight ratio) from 1:100 to 1:5 were used. To achieve the highest K/S and the deodorizing and antibacterial performance, the best liquor ratio, dyeing bath ratio, dyeing temperature and dyeing time were found to be 1:10, 1:50, $80^{\circ}C$ and 60 min, respectively. The deodorizing performance of dyed cotton, silk and wool fabrics against acetic acid vapor were found to be95,70,90%,respectively. However, all the dyed fabrics displayed outstanding deodorizing performance(99%) against ammonia gas and antibacterial performance(bacteriostatic reduction rate:99.9%) against Staphylococcu aureus and Klebsiella pneumonia(bacteriostatic reduction rate: 99.9%). It is worth noting that pomegranate (Punica granatum L.) colorants notably enhanced the deodorizing and antibacterial performance of cotton, silk and wool fabrics.

• 한국산학기술학회논문지
• /
• 제21권6호
• /
• pp.672-678
• /
• 2020

국내에서 생산중인 대구경 탄약은 대부분 Ogive 부를 제조하는 방법으로 Press Nosing 공법을 적용하고 있다. Press Nosing 공법은 프레스 공정 전 후 윤활처리 등의 추가적인 공정이 필요한 단점이 있다. 본 연구에서는 이러한 단점을 개선할 수 있는 점진성형 공법 중 하나인 Swaging 공법의 대구경 탄약 적용 가능성을 제시하고자 하였다. 대구경 탄약인 155MM K307 탄체는 Press Nosing 공정을 적용하는 대표적인 제품으로, 본 연구에서는 K307 탄체의 Sub-scale 시험품을 제작하여 Swaging 공정을 적용한 소성가공 실험을 실시하였다. 최종 성형 치수를 만족하는 단면감소율 75 % 까지 소성가공이 가능한지 여부 및 Swaging 성형으로 제작된 제품의 치수만족 여부, 제품 결함 발생 여부, 단면감소율에 따른 경도 변화, 두께의 증가 등을 고찰하였다. 시험을 통해 단면적 감소율에 따라 비례적으로 경도가 증가하여 단면적 감소율 75 %에서 경도는 HV 335 이상 증가하는 것을 확인하였다. 소재두께 변화량은 이론적 계산값과 유사한 경향을 보였으며 단면 감소율 75 %에서 두께 증가율은 65.4 %로 비례함을 확인하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.136-138
• /
• 2003

Strain states of clad sheets consisted of AL3003 and SUS430 were studied by FEM simulation. Main simulation parameters include roll size, reduction, material properties, material temperature, and friction between roll and material (or friction between materials). To investigate the effect of friction on the evolution of strain states, the friction coefficient between roll and material (or fraction coefficients between materials) was varied. Components of strain rate, strain were compared according to the variation of friction coefficients. And strain states during cladding were compared with those induced by simple rolling process.

• 대한방사선기술학회지:방사선기술과학
• /
• 제41권6호
• /
• pp.611-616
• /
• 2018

Lead apron is harmful to the human body because it is made at heavy metals, and when worn for long periods of time, it causes pain. Therefore, this paper intended to improve the defects of lead apron by using new material shields. For the comparative evaluation of lead and new material shieldes, the shielding rate and weight were measured and tested based on lead 0.5 mmPb. The rate of shielding was 97% based on lead at 0.5 mm thickness, while The new material shield T3 showed similar shielding rates as lead in 8 layers, and in T2 these values were measured in 11 layers. In addition, similar shielding rate was measured in 12 layers at B2, and 8 layers in BF, and 4 layers in $BF_2$. Comparing the weight of cases when commercialized with apron, T3, T2 and B2 were heavier than lead apron. But BF, $BF_2$ were lighter than the lead apron. Based on the results of the experiment, T3 and T2 can be used as an alternative to lead if human or environmental hazards are considered a priority. However, BF and $BF_2$ should be used if the reduction of external exposure is considered a priority.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.24-31
• /
• 2002

An experimental study was conducted to investigate the effects of EGR (Exhaust Gas Recirculation) variables on performance and emission characteristics in a 2-liter 4-cylinder spark-ignition LPG fuelled engine. The effects of EGR on the reduction of thermal loading at exhaust manifold were also investigated because the reduced gas temperature is desirable for the reliability of an engine in light of both thermal efficiency and material issue of exhaust manifold. The steady-state tests show that the brake thermal efficiency increased and the brake specific fuel consumption decreased with the increase of EGR rate in hot EGR and with the decrease of EGR temperature in case of cooled EGR, while the stable combustion was maintained. The increase of EGR rate or the decrease of EGR temperature results in the reduction of NOx emission even in the increase of HC emission. Furthermore, decreasing EGR temperature by $180^{\circ}C$ enabled the reduction of exhaust gas temperature by $15^{\circ}C$ in cooled EGR test at 1600rpm/370kPa BMEP operation, and consequently the reduction of thermal load at exhaust. The optimization strategy of EGR application is to be discussed by the investigation on the effect of geometrical characteristics of EGR-supplying pipe line.