• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 한국소성가공학회 2003년도 The 8th Asian Symposium on Precision Forging ASPF
• /
• pp.162-166
• /
• 2003

In combined forward-backward extrusion with controlled forward speed by a counter punch, accurate parts with forward rod can be formed. As an extension of this method, reverse extrusion is proposed, in which the extruded forward rod is pushed back while the main punch is kept at the final position after the forward-backward extrusion process. The experiment is carried out using lead as a model material. With the reverse extrusion method, longer forward rods can be formed without under-filling defect than that by combined extrusion with controlling extrusion speed.

• Transactions of Materials Processing
• /
• 제33권3호
• /
• pp.178-184
• /
• 2024

In this study, we investigated the effects of extrusion ratio and extrusion temperature on the microstructure and tensile properties of extruded Mg-6Al-0.3Mn-0.3Ca-0.2Y (SEN6) alloy. As the extrusion ratio and temperature increase, dynamic recrystallization during extrusion is promoted, leading to the formation of a fully recrystallized microstructure with increased grain size. Additionally, the increases in extrusion ratio and temperature lead to texture strengthening, exhibiting a higher maximum texture intensity. The extruded materials contain three types of secondary phases, i.e., Al₈Mn₄Y, Al₂Y, and Al₂Ca, with irregular or polygonal shapes. The quantity, size, distribution, and area fraction of the second-phase particles are nearly identical between the two materials. Despite its larger grain size, the tensile yield strength of the material extruded at 450 ℃ and an extrusion ratio of 25 (450-25) is higher than that of the material extruded at 325 ℃ and an extrusion ratio of 10 (325-10), which is mainly attributed to the stronger texture hardening effect of the former. The ultimate tensile strength is similar in the two materials, owing to the higher work hardening rate in the 325-10 extrudate. Despite differences in grain size and recrystallization fraction, numerous twins are formed throughout the specimen during tensile deformation in both materials; consequently, the two materials exhibit nearly the same tensile elongation.

• Transactions of Materials Processing
• /
• 제6권5호
• /
• pp.446-455
• /
• 1997

A Combined extrusion operation consists of forward and backward extrusion forming and it is possible to make the process be simple by employing it. But the metal flow pattern induced by the operation is hard to analyze accurately because the flows are non-steady, which have at least two directions dependent upon each other. So engineers in the industrial factories had conducted the two extrusion operations separately. A new process was designed by the industrial expert for forming of an alu-minum preform using the combined extrusion operation. In this study, experiments and finite element analysis was carried out to determine the process parameters. Through the preliminary experiment, it was shown that warm forming condition was more desirable than cold or hot ones. And optimal shape of initial billet could be also determined. From the compatibility test, bonde-lube was chosen as the optimal lubricant and 20$0^{\circ}C$ as the material temperature by the inspection of micro-structure. The operation was simulated by the rigid-plastic finite element method to examine the metal flow. Disap-pearing of dead metal zone was observed as the punch fell down and desirable shape was obtained from the one operation. As a result of this study, 7 operations could be reduced and 225% of material saved.

• Korean Journal of Materials Research
• /
• 제5권8호
• /
• pp.953-959
• /
• 1995

It was investigated that reinforced species, billet condition and extrusion variation in Al 6061 composite material effected on extrusion process of particulate reinforced composite material. The strength of composite material with reinforcement species revealed SiC$\sub$w/> A1$_2$O$\sub$3f/ > A1$_2$O$\sub$3f/ > A1$_2$O$\sub$3f/ orderly. K$\sub$w/ increased as volute fraction increased in all composite material. The composite materials reinforced by A1$_2$ $O_3$required the larger pressure in hot extrusion process than those by SiC$\sub$p/ at all condition. Extrusion process tended to decrease as the semi-angle of extrusion dies increased because larger contact area caused larger shear friction. Extrusion temperature went up about 50$^{\circ}C$ in low elevated deformation temperature. In extrusion temperature above 500$^{\circ}C$, severe tearing occurred on extrusion surface. More reinforcement in volume fraction, more hot tearing.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.125-130
• /
• 1999

In order to reduce the forming load of backward extrusion to a feasible level a new backward extrusion processes are proposed. In these process the shape of punch and die for conventional backward extrusion are change to open backward extrusion. To analyse the process numerical simulations by the finite element method has been performed, This simulation gave good results concerning the prediction of the forming load material flow and the corresponding shape of forged products, . These predictions set the limits of the preform shape and forming load depending on the punch and die geometry. The results show that the forming load is reduced significantly when the conventional backward extrusion change to open backward extrusion.

• Progress in Superconductivity
• /
• 제3권2호
• /
• pp.193-197
• /
• 2002

There are many problems in wire fabrication of long length Bi-2223 superconductor by using conventional extrusion method. They are mainly due to high surface resistance and inhomogeneous distribution of inner stress. Hydrostatic extrusion process will not only decrease the extrusion pressure but also enhance homogeneous deformation of material by reducing friction force between billet and container Hydrostatic extrusion method is considered to be useful fur fabrication of the homogeneous wire with high density. In this paper, hydrostatic extrusion process is introduced to fabricate Bi-2223 superconducting tape, and also discussed are the interface homogeneity and microstructural aspects of extruded BSCCO/Ag billet.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.261-264
• /
• 2003

Semi-solid processing is now becoming of great interest for the production of various parts by pressure die casting. Many advantages are associated with this forming process at the condition that the forming operation is performed under appropriate conditions. The thixoforming process, which needs a suspension of a globular, non-dendritic solid phase in the liquid phase, is characterized by three major steps. The first step is casting of billets with a microstructure suited for thixoforming. The second step is reheating of slugs cut from these billets. The third step is injection of the semi-solid slugs into a die. In this paper, the horizontal reheating machine to obtain the optimal conditions suitable for semiu-solid die casting process was used and applied to extrusion material. It is estimated the possibility of application on semi-solid die casting with extrusion material through various results.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.265-268
• /
• 2003

In the extrusion process, the working material is forced to flow through a die with the desired profile. In general, the width of an extruded section is limited to about an inch less than the diameter of the round billet. But through the lip die, material is spreaded to produce a wider extruded section than the diameter of round billet. In this study, the extrusion process of an aluminum plate using the lip die is investigated. The width of the extruded plate is 450mm that is formed from the round billet with a diameter of 250mm. The flow characteristic through the lip die is considered to produce the wide-extruded plate with a small billet using rigid plastic FE analysis. Based on the result of FE analysis, new designs of lip die are proposed.

• Journal of the Korean Society for Precision Engineering
• /
• 제14권3호
• /
• pp.130-136
• /
• 1997

The velocity distrubution at the exit of extrusion die depends on the width of bearing land very much. When uniform bearing land without flow guide is used, the material which is extended through the same die does not, deflect to the constant direction, but when the flow guide is equipped and then the volume compensation is done accurately, the material deflects to one constant direction. Therfore, the part of problem can be known exactly, and extrusion products of straight shape can be produced by the corrected bearing land width.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 한국소성가공학회 2002년도 제5회 압출 및 인발가공 심포지엄
• /
• pp.23-32
• /
• 2002

The torsional forward extrusion is the process that is executed by punch travel and die rotation. The advantages of having the die rotation on this process are that forming load can be reduced and optimal die angle can be increased. This provides a possibility to extrude cold-worded material where a large extrusion force and die angle are required. Also, this process can improve the material properties owing to the high deformation and uniform strain distribution. The forming load and optimal die angle of this process are determined by the upper bound analysis using stream function and the optimization technique. To verify the theoretical result, we have carried out experiments and FE simulations using DEFORM3D.