• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.11a
• /
• pp.144-148
• /
• 1993

This paper is a study on electromagnetic wave absorption properties for the composition ratio of Ni-Zn-Fe$_2$O$_4$. Li-Zn-Fe$_2$O$_4$was composed of Fe$_2$O$_3$ 48∼51mo1%, LiO 18 ∼22mo1%, ZnO 34∼27mo1%. and sintering was carried out at 1200$^{\circ}C$. Through the experiments, the resonance phenomenon occured at low frequence range for high permeability, and vice versa. Specialy, In the case of Fe$_2$O$_3$49mol%, NiO 20mo1%, ZnO 3lmol% ,and the matching thickness was 10mm , the absorbing bandwith was 0.35 ∼0.95GHz. Also, In the case of Fe$_2$O$_3$51mo1%. NiO 22mo1%, ZnO 27mol%, we could get the absorbing bandwith of 0.45∼1.2GHz when the matching thickness was 6mm. Therefore. it is proved that electromagnetic wave absorbers with the above bandwidth range can be fabricated successful1y.

• Journal of Powder Materials
• /
• v.25 no.5
• /
• pp.375-378
• /
• 2018

Conductive and dielectric SiC are fabricated using electroless plating of Ni-Fe films on SiC chopped fibers to obtain lightweight and high-strength microwave absorbers. The electroless plating of Ni-Fe films is achieved using a two-step process of surface sensitizing and metal plating. The complex permeability and permittivity are measured for the composite specimens with the metalized SiC chopped fibers dispersed in a silicone rubber matrix. The original non-coated SiC fibers exhibit considerable dielectric losses. The complex permeability spectrum does not change significantly with the Ni-Fe coating. Moreover, dielectric constant is sensitively increased with Ni-Fe coating, owing to the increase of the space charge polarization. The improvements in absorption capability (lower reflection loss and small matching thickness) are evident with Ni-Fe coating on SiC fibers. For the composite SiC fibers coated with Ni-Fe thin films, a -35 dB reflection loss is predicted at 7.6 GHz with a matching thickness of 4 mm.

• Korean Journal of Optics and Photonics
• /
• v.30 no.1
• /
• pp.15-22
• /
• 2019

$Si_3N_4$ rib-optical waveguides for evanescent-wave integrated-optical biosensors were analytically interpreted, to derive the single-mode propagation conditions. The integrated-optical biosensor structure based on two-mode interference was proposed, and the rib width and thickness and core thickness for a single-mode and two-mode waveguide (sensing region) were proposed to be $3{\mu}m$, 2 nm, and 150 nm and $3{\mu}m$, 20 nm, and 340 nm respectively. The optical characteristics of each guided-wave mode were investigated utilizing the film mode-matching (FMM) analysis.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.3
• /
• pp.104-108
• /
• 2014

To improve emission efficiency of organic light emitting devices (OLEDs), we fabricated the tandem OLED of ITO / 2-TNATA / NPB / SH-1: 3 vol.% BD-2 / Bphen / Liq / Al / $MoO_x$ (X nm) / 2-TNATA / NPB / SH-1: 3 vol.% BD-2 / Bphen / Liq / Al structure. And emission properties of single OLED and tandem OLED with $MoO_x$ thickness as charge generation layer (CGL) were measured. The current emission efficiency and quantum efficiency of tandem OLED with $MoO_x$ of 3 nm thickness were improved compare with single OLED from 7.46 cd/A and 5.39% to 22.57 cd/A and 11.76%, respectively. In case of thicker or thinner than $MoO_x$ of 3~5 nm, the current emission efficiency and quantum efficiency were decreased, because balance of electron and hole in emission layer was not matching. The driving voltage was increased from 8 V of single OLED to 15 V of tandem OLED by thickness increase of OLED. As a result, it was possible to improve the emission efficiency of OLEDs by optimized $MoO_x$ thickness.

• Journal of Advanced Navigation Technology
• /
• v.18 no.4
• /
• pp.371-375
• /
• 2014

In this paper, the solutions of TE(transverse electric) scattering problems by a resistive strip grating over a grounded dielectric layer are analyzed by applying the PMM(point matching method) known as a numerical method of electromagnetic fileld. The boundary conditions are applied to obtain the unknown field coefficients and the resistive boundary condition is used for the relationship between the tangential magnetic field and the induced surface current density on the resistive strip. The induced surface current density of resistive strip is obtained by difference of the up and down of the magnetic field in two boundary areas of the resistive strip. The numerical results for reflected power of zeroth order mode analyzed by according as the resistivity, the width and spacing of resistive strip, the relative permittivity and thickness of dielectric layer, and incident angles. The numerical results shown in good agreement compared to those of the existing papers using FGMM(fourier galerkin moment method).

• Journal of the Korean Magnetics Society
• /
• v.3 no.2
• /
• pp.115-120
• /
• 1993

The relationship between magnetic parameter and microwave absorbing performance evaluation factor of electomagnetic wave absorber such as matching frequency, matching thickness were investigated for Ni-Zn ferrite composites. It was identified that the maximum value of ${\mu}_{r}$" is shift to low frequency with decrese Ni/Zn ratio and the value of ${\mu}_{r}$" is maximum in the case of Ni/Zn=1. All Ni-Zn ferrite composites in this study have two matching frequencies in 1-12 GHz frequency. It can be suggested that $f_{m1}$ is proportional to resonance frequency and $f_{m2}$ is proportional to the saturation magnetization.

• Korean Journal of Optics and Photonics
• /
• v.24 no.5
• /
• pp.256-261
• /
• 2013

Power conversion efficiency of the red and green phosphors was measured and analyzed. Two different samples of phosphors of thickness 50 ${\mu}m$ were prepared: one was the phosphor layer coated on the transparent substrate and the other was prepared on the reflective substrate. The 445 nm blue laser diode beam was used as the exciting beam. The conversion efficiencies of the red and green phosphor layers were 41.4% and 46%, respectively. The quantum efficiencies of the red and green phosphors were 60.4% and 53.5%, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.4
• /
• pp.270-274
• /
• 2019

In this paper, we analyze a planar electromagnetic absorber by using the mode matching technique(MMT). The proposed electromagnetic absorber has a periodic structure composed of a perfect conductor and ferrite, and the transmitted and reflected powers in response to the incident wave with parallel polarization are calculated according to the thickness of the plate. The proposed absorber shows a high absorption compared to the cases of periodic slits with vacuum or the ferrite plate itself. The solution to the reflected and transmitted powers by MMT is also verified with the results from a commercial simulator.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.652-655
• /
• 2003

In this paper, step-down piezoelectric transformer is studied. The piezoelectric transformer, made of lead zirconate titanate solid solution ceramic, is operated by a fundamental contour-extensional vibration mode. The transformer of 14mm length, 14mm width and 4.5mm thickness was made up two shape(Type I and II). The resonant frequency (fr) is 144kHz and 128kHz at the load resistant of $7.5{\Omega}$ that is a similar to calculating matching impedance. The gain (G) obtained 0.19 and 0.08 at each resonant frequency, when applied input voltage is 25V. The temperature difference with the variation of load resistant was increased with increasing load resistant and was the lowest at $7.5{\Omega}$ near the matching of output impedance.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.506-509
• /
• 2008

Mathematical models have been developed to calculate hydrodynamic characteristics of perforated-wall structures. Most of the models separate the fluid regions into front and back of the wall, assume the solution in each region, and calculate the solution by using the matching condition at the wall. The matching condition involves the permeability parameter, which can be calculated by the methods proposed by Mei et al. or Sollitt and Cross. In this study, we compare these two methods. The former is advantageous because all the related variables are known, but it gives wrong result in the limit of long waves, i.e. zero transmission and perfect reflection of very long waves. In deep water, the latter predicts smaller transmission and larger reflection than the former, and vice versa in shallow water. In the latter method, the friction coefficient decreases as the wall thickness or the porosity of the wall increases.