• Journal of the Korean Ceramic Society
• /
• v.29 no.4
• /
• pp.293-297
• /
• 1992

A proper combination of complex permeability and permittivity is necessary to produce the zero-reflection microwave absorber with an impedance matching. Increasing of dielectric permittivity and development of an impedance matching was investigated in ferrite-rubber composite specimens by addition of conducting materials. Graphite powder of high dielectric constant was added to the composite specimens to increase the permittivity. The precise estimation of graphite content to produce the matched-wave-impedance absorber at a given frequency can be made by using the numerically derived solution map of impedance matching. It was suggested that permittivity adjustment is an effective technique to obtained the microwave absorber with both good absorbing properties and small thickness as well.

• Journal of electromagnetic engineering and science
• /
• v.5 no.2
• /
• pp.97-103
• /
• 2005

This paper describes the measured results of sonobuoy transmitting antenna system for anti-submarine warfare (ASW). Since radiation pattern and power density depend on impedance matching between transmitting RF part and antenna with termination resistance, design of matching circuit is very important for sonobuoy system performance. Matching circuit is designed by Smith chart using control of L and C. In standing wave ratio(SWR) measurement using Network Analyzer, SWR of antenna with matching circuit observed 1.5 below at the assigned VHF band. It shows very excellent performance comparison with conversional product that is used for the same object. The measured vertical and horizontal radiation patterns are also shown the satisfaction of military specifications. A drop out of sonobuoy system on the sea is happened when angle of elevation direction is over 10 degrees, and it is conformed that it takes less than I second return to original signal level. The required electric power density is $83\;mW/m^2$ in the military specification, and measured electric power density is observed over average $110\;mW/m^2$ at all frequency bands.

• Journal of electromagnetic engineering and science
• /
• v.16 no.4
• /
• pp.241-247
• /
• 2016

This paper proposes the design and measurement of a 6-18 GHz front-end receiver module that has been combined into a one- channel output from a two-channel input for electronic warfare support measures (ESM) applications. This module includes a limiter, high-pass filter (HPF), power combiner, equalizer and amplifier. This paper focuses on the design aspects of reducing the noise figure (NF) and matching the phase and amplitude. The NF, linear equalizer, power divider, and HPF were considered in the design. A broadband receiver based on a combined configuration used to obtain low NF. We verify that our receiver module improves the noise figure by as much as 0.78 dB over measured data with a maximum of 5.54 dB over a 6-18 GHz bandwidth; the difference value of phase matching is within $7^{\circ}$ between ports.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.10
• /
• pp.24-31
• /
• 1997

A new design method of stable RF power amplifier using 3dB coupled line is proposed in this thiesis. The proposed method of broadband matching consist of resistive matching circuits at low frequency and lossless matching circuits at microwave band. This design method increase the stability of an amplifier and is suitable for interstage matching. When high power amplifier is designed using this method for PCS base transceiver station, the measured resutls show thst the gain of 18.5dB, and 9W (39.5dBm) output power. We use motorola's MRF6401 for medium power and MRF 6402 for large power and cascaded them.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.237-242
• /
• 2002

In this paper, active inverter bandpass filters using the impedance matching method are designed and fabricated. The designed active inverter bandpass filter is fabricated using microstrip-lines matching networks for IMT-2000 applications. Measured results show that the two-pole inverter bandpass filter for IMT-2000 application has its insertion gain of 14.1 ㏈, 75 MHz bandwidth at the center frequency 2.18 GHz and more than 23 ㏈ attenuation at fo $\pm$ 200 MHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.247-250
• /
• 1999

In this study, three kinds of Mn-Zn ferrite/Ni-Zn ferrite/$Ni_2Y$ ferroxplana prepared by the coprecipitation method was compounded with silicon rubber, and thereafter made ring-type specimens with various compositional ratio. The material constant of ferrite/rubber composite absorbers was obtaibed by the 2-port method. The material constants of the ferrite/rubber composite absorber with various compositional ratio of three kinds of ferrite were used to design the matching frequency and thickness with the impedance matching map. We were able to predict the matching condition from the design method.

• ETRI Journal
• /
• v.28 no.3
• /
• pp.393-396
• /
• 2006

This letter proposes a new impedance matching scheme of a traveling wave electro-absorption modulator (TWEAM) module for a 60 GHz band radio-over-fiber (ROF) link. A microstrip band pass filter (BPF) was used to achieve impedance matching at the 60 GHz band, and termination resistance was carefully designed to obtain an input impedance close to $50\;{\Omega}$. Also, a bias circuit for the device was designed in the module. The measured return loss and frequency response show that the modulator module observes the characteristics of a filter without the need of a further tuning process.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.6
• /
• pp.628-630
• /
• 2016

Compressive sensing can recover an original sparse signal from a few measurements. Its performance is affected by the number of non-zero elements in the signal. The knowledge of partial locations of non-zero elements can improve the recovery performance. In this paper, we apply the partial location knowledge to the multipath matching pursuit. The numerical results show it improves the signal recovery performance and the channel estimation performance in the ITU-VB channel.

• Journal of Multimedia Information System
• /
• v.5 no.2
• /
• pp.143-146
• /
• 2018

The eigen value problem of a coaxial cavity and a modified pill box cavity is investigated using the mode matching technique. The coaxial cavity has a cylindrical cavity with beam ports and center conductor. The pill box cavity is the same as a coaxial cavity without center conductor. The electric field and magnetic field are formulated in propagation region and resonance region. The boundary and orthogonal conditions are applied to the electric and magnetic fields. We derived the eigen value equation by the proposed procedure in a coaxial cavity and a modified pill box cavity. The electromagnetic field of the real structure is disturbed by the coaxial wire. The effect of the coaxial wire in pill box cavity with beam ports increase the dominant resonant frequency. The coaxial line method of the coupling impedance is not adequate for a cylindrical cavity. The results of the mode matching technique and simulation agree well. The results confirm the proposed formulation is valid.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.68 no.2
• /
• pp.304-309
• /
• 2019

This paper presents a CMOS RF-to-DC converter for video surveillance disposable IoT applications. It widely harvests RF energy of 3G/4G cellular low-band frequency range by employing a tunable impedance matching network. The proposed converter consists of the differential-drive cross-coupled rectifier and the matching network with a 4-bit capacitor array. The proposed converter is designed using 130-nm standard CMOS process. The designed energy harvester can rectify the RF signals from 700 MHz to 900 MHz. It has a peak RF-to-DC conversion efficiency of 72.25%, 64.97%, and 66.28% at 700 MHz, 800 MHz, and 900 MHz with a load resistance of 10kΩ, respectively.